Honeywell Voyager 1452g Series Quick Start Manual

Voyager™ 1452g Series
Cordless Area-Imaging Scanner
Quick Start Guide
Aller à www.honeywellaidc.com pour le français.
Vai a www.honeywellaidc.com per l'italiano.
Gehe zu www.honeywellaidc.com für Deutsch.
Ir a www.honeywellaidc.com para español.
Para Português, acesse www.honeywellaidc.com.br.
Перейти на русскоязычный сайт www.honeywellaidc.com.
Pro češtinu jdi na www.honeywellaidc.com.
Pre slovenčinu choď na
www.honeywellaidc.com
日本語 : www.honeywellaidc.com をご覧ください。
中文 （简体） ，请访问 :www.honeywellaidc.com。
中文 （繁体） ，请访问 :
www.honeywellaidc.com。
한글 로 이동합니다 .
www.honeywellaidc.com
1452-QS Rev (a)
Reading Techniques
The view finder projects an aiming
beam that should be centered over
the bar code, but it can be
positioned in any direction for a
good read.
Hold the scanner over the bar code,
pull the trigger, and center the
aiming beam on the bar code.
The aiming beam is smaller when
the scanner is closer to the code and larger when it is farther from the
code. Hold the scanner close to smaller bar codes, and farther away
from large bar codes to get a proper read.
If the bar code is highly reflective (e.g., laminated), you may need to
tilt the scanner at an angle so the bar code can be scanned.
Note: If the scanner razzes when scanning a bar code, the link has
not been established. If the scanner beeps once, the link has
been established.
Standard Product Defaults
The following bar code resets all standard product default settings.
Standard Product Defaults
Note: PDF and 2D bar codes can only be read by Voyager model
1452g2D and cannot be read by model 1452g1D.
All manuals and user guides at all-guides.com
Note: Refer to your user's guide for information about cleaning your
device.
For localized language versions of this document, go to
www.honeywellaidc.com.
Getting Started
Turn off the computer's power before connecting the base, then
power up the computer once the base is fully connected. When the
base is connected and powered up, put the scanner in the base to
establish a link. The green LED on the base flashes to indicate the
scanner's battery is charging.
Power Supply Assembly (if included)
Note: The power supply must be ordered separately, if needed.
11/14
RS485 Interface
The RS485 interface defaults to port 5B. If you have an IBM POS
terminal using port 9B, scan the appropriate code below to program
the terminal, then power cycle the cash register.
IBM Port 9B HHBCR-1
Interface
IBM Port 9B HHBCR-2
Note: For additional RS485 interface selections, see the User's
Guide for your product at our website,
www.honeywellaidc.com.
USB Serial
Scan the following code to program the scanner to emulate a regular
RS232-based COM Port. If you are using a Microsoft® Windows®
PC, you will need to download a driver from the Honeywell website
(www.honeywellaidc.com). The driver will use the next available
COM Port number. Apple® Macintosh computers recognize the
scanner as a USB CDC class device and automatically use a class
driver.
USB Serial
Note: No extra configuration (e.g., baud rate) is necessary.
USB Connection:
Keyboard Wedge Connection:
USB PC Keyboard
Scan the following code to program the scanner for a USB PC
Keyboard.
USB PC Keyboard
Keyboard Country
Scan the Program Keyboard Country bar code below, then scan
the numeric bar code(s) from page
program the keyboard for your country. As a general rule, the
following characters are not supported by the scanner for countries
other than the United States:
Interface
@ | $ # { } [ ] = / ' \ < > ~
Program Keyboard Country
Country Code Scan
Belgium 1
Denmark 8
Finland 2
France 3
Germany/Austria 4
Great Britain 7
Note: For a complete list of country codes, see the User's Guide for
your product at our website,
RS232 Serial Port Connection:
RS485 Connection:
Locked Link
If you link a scanner to a base using the Locked Link Mode, other
scanners are blocked from being linked if they are inadvertently
placed into the base. If you do place a different scanner into the
base, it will charge the scanner, but the scanner will not be linked.
2, then the Save bar code to
To use a different scanner, you need to unlink the original scanner by
scanning the Unlink Scanner bar code.
Override Locked Scanner
If you need to replace a broken or lost scanner that is linked to a
base, scan the Override Locked Scanner bar code with a new
scanner, and place that scanner in the base. The locked link will be
overridden; the broken or lost scanner's link with the base will be
removed, and the new scanner will be linked.
Country Code Scan
Italy 5
Norway 9
Spain 10
Unlinking the Scanner
Switzerland 6
USA (Default) 0
If the base has a scanner linked to it, that scanner must be unlinked
before a new scanner can be linked. Once the previous scanner is
unlinked, it will no longer communicate with the base. Scan the
Unlink Scanner bar code to unlink a scanner.
Save
www.honeywellaidc.com.
Locked Link Mode
(Single Scanner)
Override Locked Scanner
Unlink Scanner