Table of Contents
Advertisement
Options and functions
OPTIONS can be selected directly by pressing the corresponding button (see CONTROL PANEL).
If an option is not compatible with the selected program see PROGRAMS TABLE, the corresponding LED flashes rapidly 3 times
and beeps will sound. The option will not be enabled.
MULTIZONE
If there are not many dishes to be washed, a half loading may
be used in order to save water, electricity and detergent.
Select the program and then press the MULTIZONE button:
the symbol of the chosen rack will appear on the display.
By default the appliance washes dishes in all racks.
To wash only the specific rack, press this button repeatedly:
shown on the display (only lower rack)
shown on the display (only upper rack)
shown on the display (only cutlery rack)
shown on the display (option is OFF and the appliance will
wash dishes in all racks).
Remember to load the upper or lower rack only,
and to reduce the amount of detergent accordingly.
If upper rack is removed, please apply detergent directly
to tub instead of detergent dispenser.
DELAY
The start time of the program may be delayed for a period
of time between 1 and 12 hours.
1. Press the DELAY button: the corresponding «h» symbol
appears on the display; each time you press the button,
the time (1h, 2h, etc. up to max. 12h) from the start
of the selected wash cycle will be increased.
2. Select the wash program, press the START/PAUSE button
and within 4 seconds close the door: the timer will begin
counting down.
3. Once this time has elapsed, the indicator light «h» switches
off and the wash cycle begins.
To adjust the delay time and select a shorter period of time,
press the DELAY button. To cancel it, press the button
repeatedly until the selected delayed start indicator light «h»
switches off.
The DELAY function cannot be set once a wash cycle has
been started.
BOOST
The boost option delivers a cut 25%-67% of the duration for
main cycles, while ensuring an optimal level of washing and
drying. In order to do that it will require more water and energy
consumption compared to the regular full-lenght cycle. The
option can be selected on programs: Eco 50°, Dynamic Sensor
50-60°, Glass 45°.
DYNAMIC CLEAN
Thanks to the additional power jets this option provides
a more intensive and powerful wash in the lower rack,
in the specific area. This option is recommended for washing
pots and casseroles. Press this button to activate DYNAMIC
CLEAN (the indicator lights up).
TABLET (Tab)
This setting allows you to optimize the performance
of the program according to the type of detergent used.
Press the START/PAUSE button for 3 seconds (the correspon-
ding symbol will light up) if you use combined detergents
in tablet form (rinse aid, salt and detergent in 1 dose).
If you use powder or liquid detergent, this option should
be off.
OPERATION INDICATOR
A LED light projected on the floor indicates that the dishwasher
is working. One of the following operating modes can
be selected:
a) Disabled function.
b) When the cycle starts the light goes on for few seconds,
stays off during the cycle and flashes at the end of the cycle.
c) The light stays on during the cycle and flashes at the end
of the cycle (default mode).
If the delayed start was set, the light goes on either for the first
few seconds or the entire duration of the countdown, based
on whether mode b) or c) was set.
The light goes off every time the door is opened. To select
the mode you prefer, switch on the machine, hold down
button P until one of the three letters appears on the display,
press button P until you reach the desired letter (or mode),
hold down button P to confirm the selection.
Note: If Auto Door Opening is active and it opens the door,
then Operation Indicator will not flash at the end of cycle.
Auto Door Opening
Auto Door Opening is a convection drying system which automatically
opens the door during/after drying phase to ensure exceptional
drying performance every day. Door opens at the temperature that
is safe to your kitchen furniture, thus door will not be opened when
the option of BOOST is on.
As additional steam protection, special designed protection foil is added
together with the dishwasher. To see how to mount protection foil
please refer to (INSTALLATION GUIDE).
Auto Door Opening functionality could be disabled by the user
as follows:
1. Go to the Dishwasher software menu pressing and holding P button
(6 sec).
2. You are currently in Light Control Menu (please refer to OPERATION
INDICATOR description), if you don't want to change anything
please press and hold P button (until one of the two letters appears
on the display).
3. You switched to Auto Door Opening Control Menu, you could change
status of Auto Door Opening functionality by pressing P button:
E – enabled
d – disabled
To confirm the change and exit from the Control Menu please press
and hold P button (3 sec).
9
Advertisement
Table of Contents
