Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Fanmaster PERH2400
Summary of Contents for Fanmaster PERH2400
- Page 1 FA NM A ST E R cooling heating ventilation extraction INSTRUCTION MANUAL ELECTRIC PEDESTAL/WALL RADIANT HEATER MODEL: PERH2400 FOR INDUSTRIAL USE ONLY TO PREVENT SERIOUS INJURY, READ & UNDERSTAND ALL WARNINGS & INSTRUCTIONS BEFORE USE. PLEASE KEEP THIS DOCUMENT FOR YOUR RECORDS...
-
Page 2: For Your Information
FOR YOUR INFORMATION Thank you for purchasing a Fanmaster electric radiant heater. Please read this instruction manual carefully before using this heater. Disclaimer: Fanmaster reserves the right to make alterations to specifications, quantities, dimensions, for production or other reasons, subsequent to publication. - Page 3 ALWAYS CHECK THE POWER CABLE BEFORE USING THE APPLIANCE. IT MUST NOT BE BENT, TAUT, STRETCHED, CRUSHED OR ANY WAY DAMAGED. • IF THE POWER CORD AND/OR PLUG IS DAMAGED, IT MUST BE REPLACED BY FANMASTER, A SERVICE AGENT OR A QUALIFIED PERSONS. •...
-
Page 4: Product Description And Specifications
2. PRODUCT DESCRIPTION & SPECIFICATIONS PRODUCT DESCRIPTION Industrial electric pedestal or wall radiant heater. SPECIFICATIONS MODEL PERH2400 2400 W Heat Output 6,824 BTU Element Type Quartz Lamp 1 x Heat settiings Control settings Adjustable thermostat Settings (W) 2400 Voltage (V/Hz) -
Page 5: Getting To Know Your Heater
3. GETTING TO KNOW YOUR HEATER SWITCH HEATING ELEMENT BRACKET CABLE SAFETY BAR COVER/GRILLE BASE LOWER TUBE ADJUSTMENT HEIGHT KNOB TOP TUBE FIXED SLEEVES/ ADJUSTMENT ANGLE KNOBS SPACER LOCATED BUTTON FIXED AXLE PIN... - Page 6 4. ASSEMBLING & OPERATING INSTRUCTIONS Remove the heater from the carton. If the heater is damaged, please contact Fanmaster or where you purchased the heater from. How to assemble Pedestal stand 1. Using 4 x 20F head screws, fix the balance weights to the bottom of the base.
- Page 7 4. ASSEMBLING & OPERATING INSTRUCTIONS Adjust the height as required by tightening the plastic collar (110cm to 180cm) (1) Loosen the screws on the back of the heater head. (2) Fix brackets to the back of the heater head. (3) Loosen the knobs (5) (4) Attached brackets to knob (5) Tighten adjustment knob and screws.
- Page 8 4. ASSEMBLING & OPERATING INSTRUCTIONS Wall Mount installation: 1. There are 4 brackets & fasteners used with the heater. Furthermore, in the channel on the backside of the heater, there are 4 square fastener washers 25x25mm. Relieve the square washers (Fig 7.1) and fasten 2 brackets to the channel on the backsoide of the heater with the screws (Fig 7.2) 2.
-
Page 9: Cleaning, Maintenance And Storage
4. ASSEMBLING & OPERATING INSTRUCTIONS • Position the heater so it stands upright & is on a firm surface (when used as a pedestal) and at a safe distance from wet environments and flammable objects. • Connect the plug to the relevant power source. Set the thermostat knob to the MAX &... -
Page 10: Troubleshooting
7. TROUBLESHOOTING PROBLEM CAUSE SOLUTION The heater does not operate, even Disconnect the plug, check The plug is loose, bad when it is plugged the connection of the plug & connection in & the switch, socket. Try another socket thermostat is ON Element is not Power or Voltage Surge Replace Element... -
Page 11: Warranty
To make a claim under the warranty, take the product (with proof of purchase) to the store where you purchased the product or go to https://www.fanmaster.com.au/warranty-claims-returns. This warranty is given by Fanmaster Pty Ltd ABN: 45 353 934 457 Unit 1/6-8 Yalgar Rd, KIRRAWEE NSW 2232 P: 1300 900 345 E: warranties@fanmaster.com.au... - Page 12 FA NM A ST E R cooling heating ventilation extraction Fanmaster Pty Ltd | 1/6-8 Yalgar Road, KIRRAWEE NSW 2232 1300 900 345 | sales@fanmaster.com.au | www.fanmaster.com.au N11664 MADE IN CHINA...