To connect the DHW output........34 ▪ Installation instructions 7 Configuration ▪ Format: Paper (in the box of the indoor unit) Overview: Configuration ............35 7.1.1 To access the most used commands ......35 Installation manual EBSH/X(B)11+16P30+50DF Daikin Altherma 3 R ECH₂O 4P663483-1A – 2021.11...
WARNING Daikin website (publicly accessible). ▪ Do NOT pierce or burn refrigerant cycle parts. ▪ The full set of latest technical data is available on the Daikin ▪ Do NOT use means to accelerate the defrosting Business Portal (authentication required).
WARNING The backup heater MUST have a dedicated power supply and MUST be protected by the safety devices required by the applicable legislation. Installation manual EBSH/X(B)11+16P30+50DF Daikin Altherma 3 R ECH₂O 4P663483-1A – 2021.11...
Otherwise the installation manual of the Backup Heater. unit may be damaged or in extreme cases catch fire. 360° ≥100 ≥500 a ≥100 a+b ≥600 b ≥300 Screw plug EBSH/X(B)11+16P30+50DF Installation manual Daikin Altherma 3 R ECH₂O 4P663483-1A – 2021.11...
WARNING Make sure installation, servicing, maintenance and repair comply with instructions from Daikin and with applicable legislation and are executed ONLY by authorised persons. NOTICE ▪ Pipework shall be protected from physical damage.
=1.90 m + Chimney height release Installation with chimney connected to the outside. The release height is not relevant. There are no requirements to the minimum floor area. Not applicable EBSH/X(B)11+16P30+50DF Installation manual Daikin Altherma 3 R ECH₂O 4P663483-1A – 2021.11...
Page 10
1× O-ring Flat gasket ▪ Socket's connection point for the chimney = 1" male thread. Use a compatible counterpart for the chimney. ▪ Make sure the connection is airtight. Installation manual EBSH/X(B)11+16P30+50DF Daikin Altherma 3 R ECH₂O 4P663483-1A – 2021.11...
Page 11
▪ Must be a permanent opening that cannot be closed. ▪ Must be ≥50% of A (minimum bottom opening area). nv-min Min. 50% ▪ Must be ≥1.5 m from the floor. of A nv-min (≥A nv-min EBSH/X(B)11+16P30+50DF Installation manual Daikin Altherma 3 R ECH₂O 4P663483-1A – 2021.11...
Page 12
Ventilation openings must comply with A and with nv-min "Conditions ventilation openings" on previous page). Min. 50% Min. 50% ΔH1 of A of A nv-min nv-min (≥A (≥A nv-min nv-min Installation manual EBSH/X(B)11+16P30+50DF Daikin Altherma 3 R ECH₂O 4P663483-1A – 2021.11...
Example: If the refrigerant charge is 4.3 kg, use the row of 4.4 kg. Total refrigerant charge (kg) (dm²) nv-min 10.1 10.4 10.6 10.9 11.1 11.3 11.5 11.8 EBSH/X(B)11+16P30+50DF Installation manual Daikin Altherma 3 R ECH₂O 4P663483-1A – 2021.11...
You must connect the drain hoses to an appropriate drain according to the applicable legislation. 1 Open the screw plug. 1× Installation manual EBSH/X(B)11+16P30+50DF Daikin Altherma 3 R ECH₂O 4P663483-1A – 2021.11...
▪ with a heat resistance of at least 120°C ▪ Insulation thickness Pipe outer diameter Insulation inner Insulation thickness (Ø diameter (Ø 9.5 mm (3/8") 12~15 mm ≥13 mm 15.9 mm (5/8") 17~20 mm ≥13 mm Ø Ø Ø Ø EBSH/X(B)11+16P30+50DF Installation manual Daikin Altherma 3 R ECH₂O 4P663483-1A – 2021.11...
▪ Water temperature. All installed piping and piping accessories See the recommended procedure as described in "8.2 Checklist commissioning" [ 4 44]. (valve, connections,…) MUST withstand following during temperatures: Installation manual EBSH/X(B)11+16P30+50DF Daikin Altherma 3 R ECH₂O 4P663483-1A – 2021.11...
Do NOT exceed the maximum tightening torque (Thread size 1", 25-30 N•m). To avoid damage, apply the necessary countertorque with a suitable tool. ≤Ø7 mm EBSH/X(B)11+16P30+50DF Installation manual Daikin Altherma 3 R ECH₂O 4P663483-1A – 2021.11...
1 m water column = 0.1 bar). Make sure that the pressure relief valve does not open. 6 Close the manual air vent valves as soon as water emerges free of bubbles. Installation manual EBSH/X(B)11+16P30+50DF Daikin Altherma 3 R ECH₂O 4P663483-1A – 2021.11...
1 Open the shut-off valve for the cold water supply. 2 Open all hot water taps in the system to make sure that the tapped water flow is as high as possible. EBSH/X(B)11+16P30+50DF Installation manual Daikin Altherma 3 R ECH₂O 4P663483-1A – 2021.11...
"6.3.12 To connect the safety least 20 mm to prevent condensation on the surface of the thermostat (normally closed insulation. contact)" [ 4 31]. Smart Grid "6.3.13 To connect a Smart Grid" [ 4 32]. Installation manual EBSH/X(B)11+16P30+50DF Daikin Altherma 3 R ECH₂O 4P663483-1A – 2021.11...
Wires: 2×0.75 mm² account adequately. The cable routing in normal position is longer than in service position. [9.B.1]=2 (External sensor = Room) [1.7] Room sensor offset EBSH/X(B)11+16P30+50DF Installation manual Daikin Altherma 3 R ECH₂O 4P663483-1A – 2021.11...
2 Connect the main power supply. In case of normal kWh rate power supply Interconnection Wires: (3+GND)×1.5 mm² cable Power supply Wires: 1N+GND indoor unit Maximum running current: 6.3 A — Installation manual EBSH/X(B)11+16P30+50DF Daikin Altherma 3 R ECH₂O 4P663483-1A – 2021.11...
MUST be protected by the safety devices required by the applicable legislation. CAUTION To guarantee the unit is completely earthed, ALWAYS connect the backup heater power supply and the earth cable. EBSH/X(B)11+16P30+50DF Installation manual Daikin Altherma 3 R ECH₂O 4P663483-1A – 2021.11...
Page 26
Connect the backup heater power supply as follows: 1N~, 50 Hz 230 V AC Model (power Connections to backup heater power supply) supply *3V (3V: 1N~ 230 V) SWB2 Q1DI 1N~, 50 Hz 230 V AC Installation manual EBSH/X(B)11+16P30+50DF Daikin Altherma 3 R ECH₂O 4P663483-1A – 2021.11...
2 Switch box 3 Switch box cover 4 Top cover 2 Connect both connection cables from the backup heater EKECBU* to the appropriate connectors as shown in the illustration below. EBSH/X(B)11+16P30+50DF Installation manual Daikin Altherma 3 R ECH₂O 4P663483-1A – 2021.11...
3 Switch box cover terminals as shown in the illustration below. 4 Top cover 2 Connect the electricity meters cable to the appropriate terminals as shown in the illustration below. Installation manual EBSH/X(B)11+16P30+50DF Daikin Altherma 3 R ECH₂O 4P663483-1A – 2021.11...
2 Connect the alarm output cable to the appropriate terminals as 4 Top cover shown in the illustration below. 2 Connect the space cooling/heating ON/OFF output cable to the appropriate terminals as shown in the illustration below. EBSH/X(B)11+16P30+50DF Installation manual Daikin Altherma 3 R ECH₂O 4P663483-1A – 2021.11...
4 Top cover 2 Install the switch box metal insert. 2 Connect the changeover to external heat source cable to the appropriate terminals as shown in the illustration below. Installation manual EBSH/X(B)11+16P30+50DF Daikin Altherma 3 R ECH₂O 4P663483-1A – 2021.11...
8H-03 will occur. Safety thermostat contact: 16 V DC detection (voltage supplied by PCB). The voltage-free contact shall ensure the minimum applicable load of 15 V DC, 10 mA. EBSH/X(B)11+16P30+50DF Installation manual Daikin Altherma 3 R ECH₂O 4P663483-1A – 2021.11...
Jumper (factory-mounted). If you also connect a safety thermostat (Q4L), replace the jumper with the safety thermostat wires. Smart Grid pulse meter 1 Install the switch box metal insert. Installation manual EBSH/X(B)11+16P30+50DF Daikin Altherma 3 R ECH₂O 4P663483-1A – 2021.11...
Page 33
3 Install the components of the Smart Grid relay kit as follows: 9 10 X 5M.10 X 5M.9 X 5M 2× 2× 5 Connect the high voltage wiring as follows: EBSH/X(B)11+16P30+50DF Installation manual Daikin Altherma 3 R ECH₂O 4P663483-1A – 2021.11...
4 Top cover 2 Connect the DHW signal cable as shown in the illustration below. 6.3.15 To connect the solar input Wires: 0.5 mm² Solar input contact: 5 V DC (voltage supplied by PCB) Installation manual EBSH/X(B)11+16P30+50DF Daikin Altherma 3 R ECH₂O 4P663483-1A – 2021.11...
(via the unit), the configuration wizard starts to help you configure the system. The Advanced user pin code is 1234. Additional menu items for the user are now visible. EBSH/X(B)11+16P30+50DF Installation manual Daikin Altherma 3 R ECH₂O 4P663483-1A – 2021.11...
When confirmed, the system will restart and recent changes will be applied. Installation manual EBSH/X(B)11+16P30+50DF Daikin Altherma 3 R ECH₂O 4P663483-1A – 2021.11...
Page 37
NOTICE An overpressure bypass valve can be integrated in the system. Keep in mind that this valve might not be shown on the illustrations. EBSH/X(B)11+16P30+50DF Installation manual Daikin Altherma 3 R ECH₂O 4P663483-1A – 2021.11...
If the storage temperature setpoint is higher than 50°C and 0: Underfloor Maximum 55°C Variable no auxiliary boiler is installed, Daikin recommends NOT to heating disable the backup heater second step because it will have 1: Fancoil unit Maximum 55°C...
Influence of the LWT setpoint mode [2.4] is as follows: ▪ In Fixed LWT setpoint mode, the scheduled actions consist of desired leaving water temperatures, either preset or custom. EBSH/X(B)11+16P30+50DF Installation manual Daikin Altherma 3 R ECH₂O 4P663483-1A – 2021.11...
ON/OFF condition. 7.4.2 Additional zone Thermostat type Only applicable in external room thermostat control. For more info zone" [ 4 42]. about the functionality, see "7.4.1 Main Installation manual EBSH/X(B)11+16P30+50DF Daikin Altherma 3 R ECH₂O 4P663483-1A – 2021.11...
Add zone pump fixed PWM Main zone pump fixed PWM Mixing valve turning time Only applicable in Swedish language. INFORMATION Depending on the selected installer settings and unit type, settings will be visible/invisible. EBSH/X(B)11+16P30+50DF Installation manual Daikin Altherma 3 R ECH₂O 4P663483-1A – 2021.11...
The power supply voltage matches the voltage on the commissioning checklist is also available on the Daikin identification label of the unit. Business Portal (authentication required). There are NO loose connections or damaged electrical The general commissioning checklist is complementary to components in the switch box.
1 Set the user permission level to Installer. See "To — level" [ 4 35]. change the user permission 2 Go to [A.2]: Commissioning > Actuator test run. EBSH/X(B)11+16P30+50DF Installation manual Daikin Altherma 3 R ECH₂O 4P663483-1A – 2021.11...
▪ Show the user what to do for the maintenance of the unit. ▪ Explain the user about energy saving tips as described in the operation manual. Installation manual EBSH/X(B)11+16P30+50DF Daikin Altherma 3 R ECH₂O 4P663483-1A – 2021.11...
10 Technical data Technical data A subset of the latest technical data is available on the regional Daikin website (publicly accessible). The full set of latest technical data is available on the Daikin Business Portal (authentication required). 10.1 Piping diagram: Indoor unit...
(1) Main power connection (1) Main power connection SWB1 Main switch box Outdoor unit Outdoor unit SWB2 Backup heater switch box SWB1 Switch box (2) User interface (2) User interface Installation manual EBSH/X(B)11+16P30+50DF Daikin Altherma 3 R ECH₂O 4P663483-1A – 2021.11...
Page 49
Smart Grid contacts Smartgrid feed-in Smart Grid feed-in Solar input Solar input Space C/H On/OFF output Space cooling/heating On/OFF output SWB1 Switch box (4) Option PCBs (4) Option PCBs EBSH/X(B)11+16P30+50DF Installation manual Daikin Altherma 3 R ECH₂O 4P663483-1A – 2021.11...
Page 50
2 core Power limitation demand input 4 Only for remote user interface 2 core A8P: X801M: 4-5 signal 2×0.75 X 5M: 11-12 A14P: P1-P2 user interface communication 4D135453 Installation manual EBSH/X(B)11+16P30+50DF Daikin Altherma 3 R ECH₂O 4P663483-1A – 2021.11...
Page 52
4P663483-1 A 00000000 4P663483-1A 2021.11 Verantwortung für Energie und Umwelt...