OPERATING INSTRUCTIONS
Please read the following instructions carefully before connecting this timer to electrical appliances.
WARNING!
For indoor use only.
Do not connect after each other.
To disconnect voltage pull the plug.
Don't plug in an appliance where the load exceeds 16 Amp. Always ensure the plug of any appliance is fully inserted into the timer outlet. If cleaning
of the timer is required, remove from mains power and wipe timer with a dry cloth.
DO NOT IMMERSE TIMER IN WATER OR ANY OTHER LIQUID.
Heaters and similar appliances should never be left unattended during operation. The manufacturer recommends such appliances not be connected
to timers.
1. R: Clear all data in memory including current time and all programs.
2. PROG/+: Set current time combined with buttons SET, —; Set programs combined with buttons SET, —; Set CD combined with buttons SET,
—; Press PROG/+ and — buttons simultaneously to enter CLOCK mode under Program setting mode or CD setting mode.
3. SET: Set current time combined with buttons PROG/+, —; Set programs combined with buttons PROG/+, —; Set CD combined with buttons
PROG/+, —;
4. —: Set current time combined with buttons SET, PROG/+; Set programs combined with buttons SET, PROG/+; Set CD combined with buttons
SET, PROG/+;
5. RND: Set or cancel RANDOM function.
6. CD (COUNT DOWN): Set or cancel CD function.
7. MANUAL: Select operating modes (ON, AUTO, OFF) of timer; Override programs or recall the overridden programs in setting programs.
1. Power LED indicator
2. 10 ON/OFF programs with 1 minute step.
3. MANUAL ON/AUTO/MANUAL OFF selectable.
5. LCD display with second.
6. Summer time function available.
8. 16 combinations of day or blocks of days available as follows:
MO
TU
WE
MO, TU, WE, TH, FR, SA
9. Maximum of 99 hours 59 minutes 59 seconds CD (COUNT DOWN) function.
: Backlight.
10.
1. Plug the timer into a regular 230 Volts power outlet and turn the power on. Leave for approximately 10 minutes to charge the Memory Back -up
battery.
2. Clear all current information by pressing R button with a sharp object such as a pen or pencil after charging.
3. The timer is now ready to be set up for use.
1. Press PROG/+ button or — button until the CLOCK displays in LCD.
2. Press SET button 2 seconds at least until "MO" for Monday begin to flash, press PROG/+ or — button to select the day of the week.
3. Press SET button again to advance to the hour setting. The "HOUR" will begin to flash, press PROG/+ or — button to select the current hour.
4. Press SET button again to advance to the minute setting. The minutes will begin to flash, press PROG/+ or — button to select the current
minute.
5. Press SET button one more time to complete the setup.
6. To reset current time, repeat above steps.
1. While the timer is at clock display status, press PROG/+ button once to display the first ON setting 1
2. Press SET button once, the "MO" will begin to flash, press PROG/+ or — button to select the day of the week or combination of days for this
program.
3. Press SET button again to advance to the hour setting. The "HOUR" will begin to flash, press PROG/+ or — button to select the ON hour for
this program.
4. Press SET button again to advance to the minute setting. The minute will begin to flash, press PROG/+ or — button to select the ON minute
for this program.
5. Press the SET button one more time to complete the program's ON setting.
6. Press PROG/+ button again to advance to the first OFF setting 1
7. Repeat the procedure 2-5 to create the OFF setting.
8. If necessary, repeat steps 1-7 for additional 9 ON/OFF settings
9. Press PROG/+ and — button simultaneously to exit program setting mode and come back CLOCK mode.
Note:
TH
FR
SA
SU
MO, WE, FR
TU, TH, SA
IMPORTANT
KEYB0ARD DEFINITION
GENERAL FEATURES
MO, TU, WE, TH, FR, SA, SU
MO, TU, WE
TH, FR, SA
INITIAL OPERATION
SETTING CURRENT TIME
SETTING PROGRAMS
OFF
--:--.
Solight DT33
MO, TU, WE, TH, FR
MO, WE, FR, SU
ON
--:--.
SA, SU
Need help?
Do you have a question about the DT33 and is the answer not in the manual?
Questions and answers