Table of Contents

Advertisement

Available languages

Available languages

Quick Links

AP-876 用バーコード読み取り装置(オプション)
Bar code reader for AP-876 (optional)
AP-876 用条码阅读器(选购项目)
取扱説明書  
INSTRUCTION MANUAL
使用说明书
安全に使用していただくために使用前に、必ずこの取扱説明書をお読みください。
また、いつでもすぐに読めるように、この取扱説明書を保管してください。
・バーコード読み取り装置のレーザ一光を直接覗かないでください。目に障害を及ぼす場合
があります。
警告
・人の目に向けてレーザ光を射出させないでください。目に障害を及ぼす場合があります。
・光学機器で直接レーザ光を覗き込まないでください。目に障害を及ぼす場合があります。
当製品を装着する際は、必ずミシンの電源スイッチを切ってください。
注意
また、ミシンの取扱説明書をあわせてお読みください。
Be sure to read this instruction manual before using the product for safe use of the product.
Furthermore, keep this instruction manual close by so that it is available whenever needed.
WARNING :
• Do not look directly into the laser beam of the bar code reader. The laser beam can damage eyes.
• Do not emit laser beam toward human eyes. The laser beam can damage eyes.
• Do not look into the laser beam directly using an optical device. The laser beam can damage eyes.
CAUTION :
When installing this product, be sure to turn OFF the power of the sewing machine.
Furthermore, read the instruction manual of the sewing machine as well.
为了安全地使用,请您在使用之前一定阅读本使用说明书。
另外,请您注意保管本使用说明书,以便随时查阅。
· 请不要直接用眼睛去看条码阅读器的激光光线。有可能伤害眼睛。
警告
· 请不要对着人的眼睛放射激光。有可能伤害眼睛。
· 请不要用光学仪器直接窥看激光光线。有可能伤害眼睛。
注意
安装本产品时,请一定关掉缝纫机的电源开关。
另外,请同时参阅缝纫机的使用说明书。
No.00
40119166

Advertisement

Table of Contents
loading

Summary of Contents for JUKI AP-876

  • Page 1 AP-876 用バーコード読み取り装置(オプション) Bar code reader for AP-876 (optional) AP-876 用条码阅读器(选购项目) 取扱説明書   INSTRUCTION MANUAL 使用说明书 安全に使用していただくために使用前に、必ずこの取扱説明書をお読みください。 また、いつでもすぐに読めるように、この取扱説明書を保管してください。 ・バーコード読み取り装置のレーザ一光を直接覗かないでください。目に障害を及ぼす場合 があります。 警告 ・人の目に向けてレーザ光を射出させないでください。目に障害を及ぼす場合があります。 ・光学機器で直接レーザ光を覗き込まないでください。目に障害を及ぼす場合があります。 当製品を装着する際は、必ずミシンの電源スイッチを切ってください。 注意 また、ミシンの取扱説明書をあわせてお読みください。 Be sure to read this instruction manual before using the product for safe use of the product.
  • Page 3 日本語...
  • Page 4: Table Of Contents

    目 次 1. 取り付け手順  ...........................1 2. バーコードの貼付け .......................2 3. バーコード機能について  ......................2 4. バーコード機能の設定 ......................3 5. 使用方法  ...........................4 6. バーコード構成  ........................5 7. バーコードリーダーの動作不良について  ................6...
  • Page 5: 取り付け手順

    注意 不意の起動による事故を防ぐため、必ず電源を切ってから行ってください。 1. 取り付け手順 1)   バーコードリーダー 1 を付属の ねじ 2 、座 金 3 で取付板 4 に取り付けます。    (2 箇所) 2)   一時停止スイッチ 5 に付属の取付板止めね じ 6 で固定します。 3)   電装ボックスを開けて、 MAIN基板の CN50  7 に中継ケーブル 8   を接続します。 CN50 9P 白 – 1 –...
  • Page 6: バーコードの貼付け

    ・バーコード読み取り装置のレーザ一光を直接覗かないでください。目に障害を及ぼす場合 があります。 警告 ・人の目に向けてレーザ光を射出させないでください。目に障害を及ぼす場合があります。 ・光学機器で直接レーザ光を覗き込まないでください。目に障害を及ぼす場合があります。 注意 ・ミシンの使用温度範囲内および使用温度湿度内で使用してください。 ・電源を供給した状態でコネクタの抜き差しをしないでください。 2. バーコードの貼付け バーコードは取扱説明書の巻末に添付されたものをコピーして使用してください。 3. バーコード機能について バーコード機能とは、カセット識別等の用途で、 バーコードを読み取り、対応した縫製パターンに 切り替えて縫製できる機能です。 バーコードの読み取りにより、ミシンメモリ内に 保存されたユーザパターン 999 個、パターンボ タンに登録されている縫製データ 50 個に切り替 えることが可能です。 使用するためには、AP-876 バーコードオプショ ンが必要になります。 バーコードリーダー仕様 クラス 2 レーザー製品 最大出力:1.0mW 波長:650nm 安全規格 JIS C 6802:2005 IEC60825-1+A2:2007 – 2 –...
  • Page 7: バーコード機能の設定

    4. バーコード機能の設定 4-1. バーコード機能の設定 メモリスイッチ K130 では、バーコードモードを選択します。メモリスイッチ K130( レベル 2) の 選択方法は、サービスマニュアルを参照ください。 設定 内容 説明 標準モード バーコードを使用しません。 バーコードモード バーコードを使用します。 4-2. バーコード種別の選択 メモリスイッチ K142 では、 バーコード種別を選択します。初期状態では Code39 のみ読み取ります。 付録のバーコードを印刷して使用する場合、K142 の変更は不要です。 設定 内容 説明 Code39 Code39 のみ読み取ります。 全規格 バーコードリーダーの対応する 全規格を読み取ります。 JAN、EAN、UPC-A/E、 EAN-8/13 Add-on、UPC-A/ E Add-on、Industrial2of5、 IATA、Interleaved2of5、 NW-7(Codabar)、Code39、 Code93、Code128、...
  • Page 8: 使用方法

    5. 使用方法 バーコードによる縫製パターン No 読込み動作は「型交換モード時のみ有効です。 」 1)   型交換モードの起動   モードキー   を押すと、画面上に型交換モードボタン    A  が表示されます。このボタンを押すと、 型交換モー ド画面が表示されます。 2)   バーコードモードの時は、バーコードモード表示  B が画面に表示されます。   型交換モード画面を表示しているときのみ、バーコード リーダから読み取りレーザが発光され、バーコードを読む ことができます。   バーコードを正常に読み取るとバーコードリーダから読み 取りレーザが消えます。 型交換モード画面 エラーコード一覧 エラーコード ピクト エラー内容 表示メッセージ 復帰方法 復帰場所 E010 バーコードで指定されたパターンが 指定されたパ リセット 前画面...
  • Page 9: バーコード構成

    6. バーコード構成 巻末の付録にあるバーコードシートを読み取ることで、対応する縫製パターンに切り替えることがで きます。切り離してお使いください。バーコードシートは Code39 の規格に対応しています。 Code39 以外の規格でバーコードを作成する場合、下記フォーマットに従って作成してください。 ・4 バイト ASCII コード ・" パターン種別 "、" 百の位 "、" 十の位 "、" 一の位 " D 0 0 1 パターン種別 パターン No. パターン種別   U または 0:ユーザパターンに対応します。   D または 1:パターンボタンに登録されている縫製データに対応します。 パターン No.   ユーザパターン:No.001 〜 No.999  ...
  • Page 10: バーコードリーダーの動作不良について

    7. バーコードリーダーの動作不良について バーコードリーダーが読み取りを行わない場合、バーコードリーダー側面にある SCAN ボタンを押し て、レーザーが発光することを確認してください。 SCAN ボタンを押しても発光しない場合、バーコードリーダーが故障している恐れがあります。 発光する場合には、 下記のバーコードを  1  →  2  →  3  の順で読み取り、 ミシンを再起動してください。 設定開始 Z Z 初期化 U 2 設定終了 Z Z – 6 –...
  • Page 11 ENGLISH...
  • Page 12 CONTENTS 1. Installation procedure ....................1 2. Attaching the bar code ....................2 3. Bar code function ......................2 4. Setting of the bar code function ................... 3 5. How to use ........................4 6. Bar code confi guration ....................5 7.
  • Page 13: Installation Procedure

    CAUTION : Turn OFF the power before starting the work so as to prevent accidents caused by abrupt start of the sewing machine. 1. Installation procedure Install the bar code reader 1 onto the mounting plate 4 using the screws 2 and the washers 3 (two locations) which are included as the accessories.
  • Page 14: Attaching The Bar Code

    50 sewing data registered in the pattern button can be made. To use this function, AP-876 bar code option will be required. Specifi cations for the barcode reader Class 2 laser product Maximum output: 1.0mW...
  • Page 15: Setting Of The Bar Code Function

    4. Setting of the bar code function 4-1. Setting of the bar code function On memory switch K130, select the bar code mode. Refer to the engineer’s manual for the selection method of the memory switch K130 (level 2). Setting Content Explanation Standard mode...
  • Page 16: How To Use

    5. How to use Pattern number reading by means of the bar code is "only enabled under the pattern replacement mode". 1) Activating the pattern change mode When the MODE key is pressed, the pattern change A is displayed on the screen. When this mode button button is pressed, the pattern change mode screen is dis- played.
  • Page 17: Bar Code Confi Guration

    6. Bar code confi guration By reading the bar code sheet attached at the end of this manual, the sewing pattern can be switched to the one corresponding to the selected bar code. Separate the attached bar code sheet for your use. This bar code sheet is compatible to Code39.
  • Page 18: Malfunction Of The Bar Code Reader

    7. Malfunction of the bar code reader When the bar code reader does not work, push the SCAN button on the side of the bar code reader to check if there is laser emission or not. If there is no laser emission even if the SCAN button is pushed, the bar code reader may be defective. If the laser is emitted, read the following bar codes in the order of 1 →...
  • Page 20 目 录 1. 安装顺序 .................................1 2. 条形码的粘贴 ................................2 3. 关于条形码功能 ..............................2 4. 条形码功能的设定...............................3 5. 使用方法 .................................4 6. 条形码的构成 ................................5 7. 关于条形码阅读器的动作故障 ........................6...
  • Page 21: 安装顺序

    注意 为了防止突然的起动造成的事故,请一定关掉电源之后再进行操作。 1. 安装顺序 CN50 9P 白色 – 1 –...
  • Page 22: 条形码的粘贴

    · 请不要直接用眼睛去看条码阅读器的激光光线。有可能伤害眼睛。 警告 · 请不要对着人的眼睛放射激光。有可能伤害眼睛。 · 请不要用光学仪器直接窥看激光光线。有可能伤害眼睛。 注意 · 请在缝纫机的使用温度范围内以及使用温度湿度内使用。 · 在供给了电源的状态下,请不要拔插连接器。 2. 条形码的粘贴 3. 关于条形码功能 条形码阅读器规格 – 2 –...
  • Page 23: 条形码功能的设定

    4. 条形码功能的设定 4-1. 条形码功能的设定 设定 内容 说明 4-2. 条形码种类的选择 设定 内容 说明 – 3 –...
  • Page 24: 使用方法

    5. 使用方法 型更换模式的起动 异常代码一览 异常代码 图标 异常内容 显示信息 复位方法 复位位置 – 4 –...
  • Page 25: 条形码的构成

    6. 条形码的构成 ·4 比特 ASCII 代码 ·“图案种类” 、 “百位” 、 “十位” 、 “个位” D 0 0 1 图案种类 图案 No. 图案种类 图案 No. 如果条形码两侧的空白小的话,有可能发生读取异常。因此,请把两侧的空白尽可能留得大一点。 – 5 –...
  • Page 26: 关于条形码阅读器的动作故障

    7. 关于条形码阅读器的动作故障 开始设定 初期化 设定结束 – 6 –...
  • Page 27 BARCODE SHEET...
  • Page 29 両サイドの余白が小さいと、読取り不良の原因になります。切り取り線に沿って切り離してください。 If the margin on both sides of the bar code is small, it may cause a reading error. Cut the bar codes along the dotted lines. ユーザーパターン No. 001 〜 050 / User pattern No. 001 to 050. / 用户图案 No.001 〜 No.050 –...
  • Page 30 ユーザーパターン No. 051 〜 100 / User pattern No. 051 to 100. / 用户图案 No.051 〜 No.100 – 2 –...
  • Page 31 ユーザーパターン No. 101 〜 150 / User pattern No. 101 to 150. / 用户图案 No.101 〜 No.150 – 3 –...
  • Page 32 ユーザーパターン No. 151 〜 200 / User pattern No. 151 to 200. / 用户图案 No.151 〜 No.200 – 4 –...
  • Page 33 ユーザーパターン No. 201 〜 250 / User pattern No. 201 to 250. / 用户图案 No.201 〜 No.250 – 5 –...
  • Page 34 ユーザーパターン No. 251 〜 300 / User pattern No. 251 to 300. / 用户图案 No.251 〜 No.300 – 6 –...
  • Page 35 ユーザーパターン No. 301 〜 350 / User pattern No. 301 to 350. / 用户图案 No.301 〜 No.350 – 7 –...
  • Page 36 ユーザーパターン No. 351 〜 400 / User pattern No. 351 to 400. / 用户图案 No.351 〜 No.400 – 8 –...
  • Page 37 ユーザーパターン No. 401 〜 450 / User pattern No. 401 to 450. / 用户图案 No.401 〜 No.450 – 9 –...
  • Page 38 ユーザーパターン No. 451 〜 500 / User pattern No. 451 to 500. / 用户图案 No.451 〜 No.500 – 10 –...
  • Page 39 ユーザーパターン No. 501 〜 550 / User pattern No. 501 to 550. / 用户图案 No.501 〜 No.550 – 11 –...
  • Page 40 ユーザーパターン No. 551 〜 600 / User pattern No. 551 to 600. / 用户图案 No.551 〜 No.600 – 12 –...
  • Page 41 ユーザーパターン No. 601 〜 650 / User pattern No. 601 to 650. / 用户图案 No.601 〜 No.650 – 13 –...
  • Page 42 ユーザーパターン No. 651 〜 700 / User pattern No. 651 to 700. / 用户图案 No.651 〜 No.700 – 14 –...
  • Page 43 ユーザーパターン No. 701 〜 750 / User pattern No. 701 to 750. / 用户图案 No.701 〜 No.750 – 15 –...
  • Page 44 ユーザーパターン No. 751 〜 800 / User pattern No. 751 to 800. / 用户图案 No.751 〜 No.800 – 16 –...
  • Page 45 ユーザーパターン No. 801 〜 850 / User pattern No. 801 to 850. / 用户图案 No.801 〜 No.850 – 17 –...
  • Page 46 ユーザーパターン No. 851 〜 900 / User pattern No. 851 to 900. / 用户图案 No.851 〜 No.900 – 18 –...
  • Page 47 ユーザーパターン No. 901 〜 950 / User pattern No. 901 to 950. / 用户图案 No.901 〜 No.950 – 19 –...
  • Page 48 ユーザーパターン No. 951 〜 999 / User pattern No. 951 to 999. / 用户图案 No.951 〜 No.999 – 20 –...
  • Page 49 ダイレクトパターン No. 001 〜 050 / Direct pattern No. 001 to 050. / 直接图案 No.001 〜 No.050 – 21 –...
  • Page 50 – 40 –...
  • Page 52 この製品の使い方について不明な点がありましたらお求めの販売店又は当社営業所にお問い合わせください。 ※この取扱説明書は仕様改良のため予告なく変更する事があります。 Copyright C 2012 JUKI CORPORATION Please do not hesitate to contact our distributors or agents in your area for further information when necessary. • 本書の内容を無断で転載、複写することを * The description covered in this instruction manual is subject to change for improvement of the 禁止します。...

Table of Contents