Comcast Platco TV Remote 2020 Quick Start Manual
Comcast Platco TV Remote 2020 Quick Start Manual

Comcast Platco TV Remote 2020 Quick Start Manual

Advertisement

ACTIVATING RF  
 
QuickSet 
This product shall support the following features:
 Auto Setup
 Manual Setup
 Optimized Setup Maps (OSM)
The following are descriptions of the Quickset features:
Auto Setup: Quickset allows for auto setup of the RCU by identifying devices connected through the
HDMI network. The RCU is programmed automatically over the RF link.
Manual Setup: Quickset allows for manual selection of a Brand for programming of devices without
having to go through Auto Detection and Programming. The RCU is programmed automatically over the
RF link.
Optimized Setup Maps: OSM assists the user with a UI flow to program a TV or Audio device in the
RCU. After the user selects brand through the UI, the RCU software and Quickset allows for the testing of
functions and by the user. The RCU is programmed over the RF link after the appropriate feedback is
observed by the user.
Comcast Platco TV Remote 2020 
Comcast Quick Start Guide 

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Platco TV Remote 2020 and is the answer not in the manual?

Questions and answers

Summary of Contents for Comcast Platco TV Remote 2020

  • Page 1 Comcast Platco TV Remote 2020  Comcast Quick Start Guide  ACTIVATING RF     QuickSet  This product shall support the following features:  Auto Setup  Manual Setup  Optimized Setup Maps (OSM) The following are descriptions of the Quickset features: Auto Setup: Quickset allows for auto setup of the RCU by identifying devices connected through the HDMI network.
  • Page 2 4 RED blinks before reboot   Unbind BLE  4 blinks if successful  2 blinks if unsuccessful      Features:    ‐ UE878NMEH (512K Flash/64K RAM)  ‐ BLE  ‐ Voice with single digital MEMs microphone   ‐ QS Cloud  o Same cloud Comcast accesses today, and implemented by Comcast  ‐ Tri‐color (RGB) feedback LED for user feedback    o Same tri‐color LED used in XR15 and XR16 remotes  o Charge pump circuit to support blue color  ‐ Option in battery compartment for 10 pin tag connection and 10 pin header  o Follow latest Sky EC302 design  ‐ Buzzer/Piezo for Remote Finder feature (OWMB‐9045HS‐27‐16) – optional install  ‐ SMT IR diode (Paralight L‐S15CAIR1C‐HD/ Bright LED Electronics Corp. BIR‐HMC33M‐2‐TRCA‐UEI)  ‐ PCB: Double Sided, CEM‐1, Carbon Thru Hole, Wet Film  ‐ Rubber keypad with carbon ink  ‐ ABS plastic housing ...
  • Page 3     Customer Marking Label            COMPLIANCE WITH FCC RULES AND REGULATIONS  This equipment has been tested and found to comply with the limits for a Class B digital device,  pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection  against harmful interference in a residential installation. This equipment generates, uses and can  radiate radio frequency energy and if not used in accordance with the instructions, may cause  harmful interference to radio communications.    However, there is no guarantee that interference will not occur in a particular installation. If this  equipment does cause harmful interference to radio or television reception, the user is  encouraged to try to correct the interference by one or more of the following measures:  • Reorient or relocate the receiving antenna.  • Increase or decrease the separation between the equipment and receiver.  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ...
  • Page 4 equipment without the approval of manufacturer could void the user's authority to operate this  equipment.    FCC Authorization Label  This device complies with part 15 of the FCC Rules. Operation is subject to the following two  conditions:  1. This device may not cause harmful interference.  2 This device must accept any interference received, including interference that may cause  undesired operation.  FCC ID: MG3‐R34010  Mexico  “La operación de este equipo está sujeta a las siguientes dos condiciones: (1) es posible que este equipo o dispositivo no cause interferencia perjudicial y (2) este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operación no deseada.”...

This manual is also suitable for:

Cmf v2

Table of Contents

Save PDF