Page 1
SERVICE MANUAL EU MT SERIALS 1. Caution…………………………………………………………………………2 2. Specification …………………………………………………………………6 3. Block Diagram....................7 4 . Alignment Procedure…………………………………………………………8 5. Scheme Diagram…………………………………………………………… 18 This manual is the la test a t the time of p rinting, an d does not include the modificatio n which may be made after the pr inting, by the constant improvement of product...
Page 2
SCHNEIDER ELECTRONICS GMBH-GERMANY 1. CAUTION CA UTION: Use of controls, adjustments or procedures other than those specified herein may result in hazardous radiation exposure. CA UT ION : T O RE DUCE TH E RIS K OF CA U T ION ELECTR ICA L SHOCK, DO NOT RE MOVE COVER (OR BACK).
Page 3
SCHNEIDER ELECTRONICS GMBH-GERMANY IMPORTANT SAFETY INSTRUCTIONS CAUTION: Read all of these instructions. Sa ve these instructions for later use . Follo w all W arnings and Instructions marked on the audio equipment. 1. Read Instructions-All the safety and operating instructionsshouldbe read before the productis operated. 2.
Page 4
SCHNEIDER ELECTRONICS GMBH-GERMANY PROTECTION AND LOCATION OF YOUR SET Do not use this television set near water ... for example, near a bathtub, washbowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, etc. Never expose the set to rain or water. If the set has been exposed to rain or water, unplug the set from the wall outlet and refer servicing to qualified service personnel.
Page 5
SCHNEIDER ELECTRONICS GMBH-GERMANY OPERATION OF YOUR SET 18. This television set should be operated only from the type of power source indicated on the marking label.If you are not sure of the type of power supply at your home, consult your television dealer or local power company. For television sets designed to operate from battery power, refer to the operating instructions.
Key Features Update:2010/04/7 V:1.1 机芯号 Model # 备注 MT23H 使用范围: TCL/中国大陆 ★低成本模拟电视 ★USB多媒体(图片、音乐) ★HDMI1.3接口*2 主要功能特点 ★睡眠定时 1.切台或换信源黑屏. 主要芯片 Main IC 处理芯片 型号 Module MT8223H 功能定义: 图像 动态背光 动态对比度 色温调整 Adjustable Color Temperature 4:3、全屏(16:9)、宽屏、16:9字幕 自适应 共 比例模式 Format Control 五种 背光调节 Backlight Adjust 梳状滤波Comb Filter...
Page 8
Factory Alignment Specification of normal SIACP TCL WW R&D FPD CENTER Factory Alignment Specification of normal SIACP For MT8223 serial Version:V0.1 For the following Chassis: MT8223L: MT8223H: PREPARED BY : LiuShuBiao DATE : 2010-05-13 APPROVED BY : DATE : Page 1 of 10...
Factory Alignment Specification of normal SIACP Disclosure The information contained in this document is proprietary to TCL SZ FPD lab and shall not be disclosed by the recipient to third persons without the written permission of the team leader or GM of R&D.
Page 10
Factory Alignment Specification of normal SIACP These chassises are designed for ALL GLOBE LCD TV. The main chip is from Mediatec (MT8223 series) and supports below inputs and outputs: class item MT8223L MT8223H √ √ ( PAL B/G D/K I) (DVB-T,DVB-C,DVB-S) HDMI (480i/p, 576i/p, 720p up to...
Page 11
Factory Alignment Specification of normal SIACP All final tests have to be done on a complete set including LCD panel in a room with temperature of 25+/-7°C The White Balance (color temperature) has to be performed into subdued lighted room after at least 1 hour of warm-up/burn-in.
Page 12
Factory Alignment Specification of normal SIACP following inputs require an ADC calibration for the time being. VGA(skip this step if no VGA input on the chassis) Provide a test signal 1024×768@60Hz with WhiteBlack squares. Select the corresponding FactoryMenu-> -> Auto ADC , then press ”OK” key on RemoteControl to start.
Page 13
Factory Alignment Specification of normal SIACP - Select “Picture” and press “OK” key to enter the picture submenu - Select “Contrast” item - press the subsequence RemoteControl keys “9”, “7”, “3” and “5” Press RemoteControl key “Return” To pop-up the Factory Menu in case of “HotKey” is enable.(TBD) The status of “HotKey”...
Page 14
Factory Alignment Specification of normal SIACP matching Safety Electrical requirements (ei: xxxx) High Voltage Withstanding requirements - “Voltage” 3500 VAC - “Max Leakage Current” 10 mA - “Test Time” 5 sec Insulating Resistance requirements - “Voltage” DC500V - “Threshold Max” - “Threshold Min”...
Page 15
Factory Alignment Specification of normal SIACP B GAIN R OFFSET G OFFSET B OFFSET WB Init DO / WAIT / OK Auto ADC DO / WAIT / OK Pattern Off / On PATTERN LUMA 0-255 5).Shop Init Item Sub-item Shop Init DO / WAIT / OK 6).NVM Reset Item...
Page 16
Factory Alignment Specification of normal SIACP DBC_BP 10).DesignMenu2 Item Sub-item DesignM Panel Control On/Off enu2 Panel Freq 0-255 Panel Percent 0-255 BlueMute On/Off OtherCTI On/Off On/Off FleshTone LumaControl On/Off Hotel Menu On/Off USB UPG USB download software BackIT On/Off 11).Sound Curve Item Sub-item Sound...
Page 17
Factory Alignment Specification of normal SIACP 2. Provide the a correct voltage to the board 3. Start “MTKTOOL.exe” application under MTKxx folder, and set the parameters as below picture(notice:select MT8223 chassiss): 4. Press “Browse” button to select the corresponding SW bin file to upload 5.
Page 18
332mA LDO #6 5V-TUNER SBU : MT22/21/20 MAIN SCHEMATIC 80mA AS1117 TCLNO: ..... TCL Thomson Electronics Singapore Pte. Ltd. 8 Jurong Hall Road #28-01/06 The JTC Summit SINGAPORE 609434 DESIGNATION Tel (65) 63092900 Fax (65) 63092999 Index-Lab DATE NAME DESCRIPTION...
Page 19
For 19&22 Model C167 0.1U 0.1U SBU : MT23H MAIN SCHEMATIC TCLNO: ..... TCL Thomson Electronics Singapore Pte. Ltd. 8 Jurong Hall Road #28-01/06 The JTC Summit SINGAPORE 609434 DESIGNATION Tel (65) 63092900 Fax (65) 63092999 Index-Lab DATE NAME DESCRIPTION...