Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for HIKVISION DS-K1107 Series
Summary of Contents for HIKVISION DS-K1107 Series
- Page 1 DS-K1107 Series Card Reader User Manual...
- Page 2 LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA OR DOCUMENTATION, IN CONNECTION WITH THE USE OF THIS PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF...
- Page 3 DS-K1107 Series Card Reader THE POSSIBILITY OF SUCH DAMAGES. REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF PRODUCT SHALL BE WHOLLY AT YOUR OWN RISKS. HIKVISION SHALL NOT TAKE ANY RESPONSIBILITES FOR ABNORMAL OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER ATTACK, HACKER ATTACK, VIRUS INSPECTION, OR OTHER INTERNET SECURITY RISKS;...
- Page 4 DS-K1107 Series Card Reader Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
- Page 5 DS-K1107 Series Card Reader subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. EU Conformity Statement This product and - if applicable - the supplied accessories too are marked with "CE"...
- Page 6 DS-K1107 Series Card Reader lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to your supplier or to a designated collection point. For more information see: www.recyclethis.info. Industry Canada ICES-003 Compliance This device meets the CAN ICES-3 (A)/NMB-3(A) standards requirements.
- Page 7 DS-K1107 Series Card Reader All the electronic operation should be strictly compliance with the electrical safety regulations, fire prevention regulations and other related regulations in your local region. Please use the power adapter, which is provided by normal company.
- Page 8 DS-K1107 Series Card Reader The device cover for indoor use shall be kept from rain and moisture. Exposing the equipment to direct sun light, low ventilation or heat source such as heater or radiator is forbidden (ignorance can cause fire danger).
- Page 9 DS-K1107 Series Card Reader power supply, which is nonswitched and linear. To guarantee the communication between the controller and the card reader, you must use RVVP cable above 0.5 to connect them. If the card reader is installed outside or in environment easy to permeable, it is advisable to install a waterproof shield.
-
Page 10: Table Of Contents
DS-K1107 Series Card Reader Content Chapter 1 Introduction ............10 Over View ..............10 Indicator and Component ..........11 Chapter 2 Installation ............12 Introduction for DIP Switch ......... 12 Definition of Cable ............13 Wiring Cables .............. 13 Installing Card Reader ..........15 Chapter 3 Sound Prompt and Indicator ...... -
Page 11: Chapter 1 Introduction
Chapter 1 Introduction 1.1 Over View Figure 1-1 DS-K1107 Series Card Reader DS-K1107 series card reader is a kind of high-performance product, with a 32 bit high-speed processor. It communicates with access controller via either RS-485 protocol (AES encrypted) or Wiegand protocol. -
Page 12: Indicator And Component
DS-K1107 Series Card Reader 1.2 Indicator and Component Figure 1-2 2.2 Indicator and Component... -
Page 13: Chapter 2 Installation
DS-K1107 Series Card Reader Chapter 2 Installation 2.1 Introduction for DIP Switch The DIP switch module is shown below. The No. of DIP switch from left to right is 1 ~ 8. Figure 2-1 DIP Switch Module Table 2-1 Description of DIP Switch... -
Page 14: Definition Of Cable
DS-K1107 Series Card Reader Description DIP Switch Status protocol. 0: RS-485 protocol. 1: Wiegand protocol Wiegand Protocol of 26-bit; (available when No. 6 is 1) 0: Wiegand protocol of 34-bit. Matched Resistance 1: Enable; (available for RS-485 protocol) 0: Disable. - Page 15 DS-K1107 Series Card Reader establish the communication between them. Steps for RS-485 communication mode: Set the DIP switch of No. 6 as 0. Set the DIP switch of No. 1 ~ 4 for RS-485 address and reading card mode. For details, please refer to 2.1 Introduction for DIP Switch.
-
Page 16: Installing Card Reader
DS-K1107 Series Card Reader shown below. Controller eader Card Reader Card Reader Figure 2-4 Wiring for Wiegand Communication Mode 2.4 Installing Card Reader Before you start: Set the DIP switch. For details, refer to 2.1 Introduction for DIP Switch. -
Page 17: Chapter 3 Sound Prompt And Indicator
DS-K1107 Series Card Reader Installation for DS-K1101/ 02/ 03/ 04 series card reader Steps: 1. Fix the plate on the wall or other places by using two screws (PA4×25-SUS). Make sure the arrows on the plate are upwards. 2. Check whether the plate is fixed and in the right direction. - Page 18 DS-K1107 Series Card Reader times. At last the buzzer will send out a beep sound indicating the starting up process is completed. When using the card reader, it will send out different sounds prompt and the LED indicator to indicate different statuses. You can refer to tables below for detailed information.
- Page 19 DS-K1107 Series Card Reader Table 1-2 Description of LED Indicator LED Indicator Status Description Green (blink for 1 time), and red (blink The card reader is power on. for 3 times) For Card + Fingerprint authentication: prompt for pressing the fingerprint after swiping the card.
- Page 20 DS-K1107 Series Card Reader UD05519B-A...
Need help?
Do you have a question about the DS-K1107 Series and is the answer not in the manual?
Questions and answers