Table of Contents
Advertisement
Out of range or no pwr at base shows on the handset screen.
•
The handset may be out of range. Move it closer to the telephone base.
•
Make sure the power cord is securely plugged into the telephone base. Use a working
electrical outlet not controlled by a wall switch.
•
Reset your telephone by unplugging the power adapter from the telephone base.
Disconnect the battery from the cordless handset. Wait for 15 seconds, then plug in the
power adapter and install the battery again. Place the handset in the telephone base and
allow up to one minute for the handset and telephone base to synchronize.
•
Other electronic products such as HAM radios and other DECT phones can cause
interference with your cordless phone. Try installing your phone as far away as possible
from these types of electronic devices.
I subscribe to a nontraditional telephone service that uses my computer
to establish connections, and my telephone doesn't work.
•
Make sure your computer is powered on.
•
Make sure your Internet connection is working properly.
•
Make sure that the software is installed and running for your nontraditional
telephone service.
•
Make sure to plug your USB telephone adapter into a dedicated USB port on your
computer. Do not plug into a multiple port USB hub (USB splitter) that is not powered.
•
In a few rare instances, the USB port on your computer may not have enough power. In
these instances, try using a USB hub with its own external power supply.
•
If you are using a firewall, it may prevent access to your nontraditional telephone service.
Contact your service provider for more information.
Common cure for electronic equipment.
•
If the telephone is not responding normally, put the cordless handset in the
telephone base. If it does not respond, try the following (in the order listed):
1. Disconnect the power to the telephone base.
2. Disconnect the battery on the cordless handset.
3. Wait a few minutes before connecting power to the telephone base.
4. Install the battery again and place the cordless handset in the telephone base.
5. Wait for the cordless handset to synchronize with the telephone base. Allow up to
one minute for this to take place.
Important safety instructions
When using your telephone equipment, basic safety precautions should always be followed to reduce
the risk of fire, electric shock and injury, including the following:
1.
Read and understand all instructions.
2.
Follow all warnings and instructions marked on the product.
3.
Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use
a damp cloth for cleaning.
4.
Do not use this product near water such as near a bath tub, wash bowl, kitchen sink, laundry tub or
a swimming pool, or in a wet basement or shower.
5.
Do not place this product on an unstable table, shelf, stand or other unstable surfaces.
6.
Slots and openings in the back or bottom of the telephone base and handset are provided for
ventilation. To protect them from overheating, these openings must not be blocked by placing the
product on a soft surface such as a bed, sofa or rug. This product should never be placed near
or over a radiator or heat register. This product should not be placed in any area where proper
ventilation is not provided.
7.
This product should be operated only from the type of power source indicated on the marking
label. If you are not sure of the type of power supply in your home or office, consult your dealer or
local power company.
8.
Do not allow anything to rest on the power cord. Do not install this product where the cord may be
walked on.
9.
Never push objects of any kind into this product through the slots in the telephone base or handset
because they may touch dangerous voltage points or create a short circuit. Never spill liquid of any
kind on the product.
10.
To reduce the risk of electric shock, do not disassemble this product, but take it to an authorized
service facility. Opening or removing parts of the telephone base or handset other than specified
access doors may expose you to dangerous voltages or other risks. Incorrect reassembling can
cause electric shock when the product is subsequently used.
11.
Do not overload wall outlets and extension cords.
12.
Unplug this product from the wall outlet and refer servicing to an authorized service facility under
the following conditions:
A.
When the power supply cord or plug is damaged or frayed.
B.
If liquid has been spilled onto the product.
C.
If the product has been exposed to rain or water.
D.
If the product does not operate normally by following the operating instructions. Adjust only
those controls that are covered by the operation instructions. Improper adjustment of other
controls may result in damage and often requires extensive work by an authorized technician to
restore the product to normal operation.
E.
If the product has been dropped and the telephone base and/or handset has been damaged.
F.
If the product exhibits a distinct change in performance.
13.
Avoid using a telephone (other than cordless) during an electrical storm. There is a remote risk of
electric shock from lightning.
14.
Do not use the telephone to report a gas leak in the vicinity of the leak. Under certain
circumstances, a spark may be created when the adapter is plugged into the power outlet, or
when the handset is replaced in its cradle. This is a common event associated with the closing
of any electrical circuit. The user should not plug the phone into a power outlet, and should
not put a charged handset into the cradle, if the phone is located in an environment containing
concentrations of flammable or flame-supporting gases, unless there is adequate ventilation. A
spark in such an environment could create a fire or explosion. Such environments might include:
medical use of oxygen without adequate ventilation; industrial gases (cleaning solvents; gasoline
vapors; etc.); a leak of natural gas; etc.
15.
Only put the handset of your telephone next to your ear when it is in normal talk mode.
16.
The power adapters are intended to be correctly oriented in a vertical or floor mount position. The
prongs are not designed to hold the plug in place if it is plugged into a ceiling, under-the-table or
cabinet outlet.
SAVE THESE INSTRUCTIONS
10
Advertisement
Table of Contents
