Page 2
INTRODUCTION The D-Link DES-1005P 5-Port 10/100Mbps Unmanaged Desktop PoE Switch is capable of feeding power to Power over Ethernet (PoE) devices such as network cameras. The DES- 1005P has 5 ports operating at 10/100 Mbps with 4 PoE+ ports (Ports 1 to 4) with a total PoE budget of 60W, making it ideal for home and small office use.
BEFORE SETTING UP THE DES-1005P Please follow the steps below to set up the switch: 1. Install the DES-1005P in a cool and dry place. Refer to the Technical Specifications for the acceptable operating temperature and humidity ranges. 2. Install the switch in a site free from strong electromagnetic source, vibration, dust, and direct sunlight.
Page 4
Plug the AC power cord into a free outlet or surge protector, then plug the other end of the DC power jack into the power port of the DES-1005P. The Power LED will illuminate confirming that the device has powered up successfully.
Page 5
Port power is not activated Amber Solid light Total power consumption is above 53W. PoE Max. Blinking Output power to PoE devices has exceeded the maximum power budget (60W). Light off Total power consumption is below Power Guard Band (53W). DES-1005P...
- Ensure the Port LED is illuminated or flashing. If not, try using a new Ethernet cable. 3. WHAT SHOULD I DO IF A POE DEVICE IS NOT POWERED BY THE DES-1005P? - Ensure that the PoE device is connected to one of the four PoE enabled ports (1 to 4) and the connected PoE devices do not exceed the maximum power budget of 60 W.
INTRODUCTION Le D-Link DES-1005P est un commutateur PoE de bureau non géré à 5 ports 10/100 Mbps qui permet d'alimenter des dispositifs Power over Ethernet (PoE, alimentation électrique par câble Ethernet) comme des caméras réseau. Le DGS-1005P possède 5 ports fonctionnant à 10/100 Mbits/s dont 4 ports PoE (Ports 1 à...
DU PRODUIT AVANT DE CONFIGURER LE DES-1005P Procédez comme suit pour configurer le commutateur : 1. Installez le DES-1005P dans un endroit frais et sec. Reportez-vous aux caractéristiques techniques pour trouver les plages acceptables de température et d'humidité de fonctionnement.
Page 12
Branchez le cordon d'alimentation secteur sure prise libre ou un parasurtenseur, puis branchez l'autre extrémité de la prise d'alimentation CC sur port d'alimentation du DES-1005P. Le voyant d'alimentation s'allumera pour confirmer que le dispositif a été correctement mis sous tension.
Page 13
PoE Max. allumé à 53 W. Clignote La sortie d'alimentation vers les dispositifs PoE a dépassé le budget de puissance maximale (60 W). Éteint Éteint La consommation d'énergie totale est inférieure à la bande garde de la puissance (53 W). DES-1005P...
- Assurez-vous que le voyant du port est allumé ou qu'il clignote. Sinon, essayez d'utiliser un nouveau câble Ethernet. 3. QUE FAIRE SI UN DISPOSITIF POE N'EST PAS ALIMENTÉ PAR LE DES-1005P ? - Assurez-vous que le dispositif PoE est connecté à un des quatre ports PoE (1 à 4) et que les dispositifs PoE connectés ne dépassent pas le budget de puissance maximale de 60 W.
ASSISTANCE TECHNIQUE Vous avez des difficultés à installer votre nouveau produit ? Le site Web de D-Link contient la toute dernière documentation utilisateur et les mises à jour logicielles des produits D-Link. Les clients américains et canadiens peuvent contacter l'assistance technique de D-Link par le biais de notre site Web.