Advertisement
Make sure that each stand is securely located under a strong point on the vehicle; consult the vehicle manufacturer's
9
handbook for guidance. Ensure that height adjust locking mechanism is fully located before applying any load
to the axle stand.
Ensure that the load is located centrally on the saddle, and that the weight is directed through the vertical axis of
9
the stand. Exercise extra care when using with a three wheeled vehicle or a trailer. Refer to vehicle manufacturer's
instructions.
Once vehicle is supported, ensure that the vehicle and stands are stable before starting work. Ensure that it is not
9
possible for the vehicle to move before commencing any work.
Inspect stands before each use. DO NOT use if they show signs of damage. DO NOT use if it is suspected that they
9
have been overloaded.
Before commencing any work or going beneath the vehicle, undertake a risk assessment. Ensure that a responsible
9
person is aware of the work about to be undertaken.
Replace any labels on the axle stand should they become unreadable. This applies in particular to any warning or operation
9
instruction labels. If replacement labels are required, contact your Sealey stockist.
DO NOT use axle stands on the highway, or anywhere else if it is deemed to be unsafe.
8
DO NOT push or twist the vehicle/load whilst it is supported on stands.
8
DO NOT mix components between stands. Use only as supplied.
8
DO NOT allow children or animals in the vicinity of a vehicle supported on axle stands.
8
DO NOT leave a vehicle on axle stands in an area that could be considered a hazard to others or property.
8
FOLLOW STEPS 1, 2, AND 3 TO CORRECTLY PLACE VEHICLE / LOAD ONTO AXLE STANDS.
9
2. INTRODUCTION
Single-piece hydraulic unit with heavy chassis design and large jacking saddle (Pad available as optional extra - Model No. JP17). Universal joint
release mechanism allows safer, more controlled lowering of the jack. Twin piston Super Rocket Lift feature brings lifting arm straight into contact
with the jacking point. Polyurethane wheels for smoother maneuverability and helps prevent damage to workshop floor. Fitted with safety overload
valve and pump-through valve to prevent handle locking at maximum ram extension. Ideal for loaded vans up to 3.5tonne GVW. Supplied with Pin
Type Axle Stands, 3tonne (3000kg) capacity per stand (6tonne (6000kg) per pair).
3. SPECIFICATION
Model No ......................................................... 3015CXHV.V2
Jack
Min. saddle height ...................................................... 120mm
Max. saddle height ..................................................... 456mm
Max. chassis height .................................................... 162mm
Length ........................................................................ 680mm
Consumable parts: Jack pad ..........................................JP17
Axle stands:
Min. working height .................................................... 290mm
Max. working height ................................................... 435mm
4. OPERATION - JACK
4.1.
BEFORE FIRST USE
4.1.1.
Assemble the handle by pushing two halves together and turn until button engages.
4.1.2.
Loosen location bolt at the back of the handle base. Insert the jack handle and tighten the bolt.
4.1.3.
Before using jack, purge the hydraulic unit in order to eliminate any air in the system. Open the valve by turning the handle
anti-clockwise (fig.1), and pumping 8 or 9 times. When complete, close the release valve by turning the handle fully clockwise (fig.1).
4.1.4.
Place a few drops of hydraulic jack oil onto the pump piston and pump the handle several times to distribute the oil. Thoroughly
lubricate all moving parts.
GENERAL JACKING
WARNING! Before lifting ensure Section 1 Safety Instructions are read and understood.
‰
4.1.5.
Prepare the vehicle as mentioned in the safety instructions ensuring the ground on which the jack is to stand is level and solid (not
tarmacadam) and use chocks under wheels of vehicle.
4.1.6.
Position the jack saddle under the vehicle manufacturer's recommended lifting point.
4.2.
JACKING THE VEHICLE
4.2.1.
Turn the handle clockwise to close the release valve (fig.1) and commence pumping handle up and down until the jack saddle reaches
the vehicle jacking point. Check the jacking point is centrally located on the saddle and continue to pump the handle to raise the vehicle.
4.2.2.
Should the jack become overloaded, a safety excess pressure valve will open and stop the jack from lifting.
© Jack Sealey Limited
Original Language Version
S
3015CXHV.V2 Issue 1 28/01/21
Advertisement
