Sony DR-CX530E Service Manual page 31

2-1-7. LCD SECTION-2
(Projector Model)
Refer to page 2-11 about Non Projector Model.
302
(Note 2)
303
(Claws)
(Claws)
301
312
313
Ref. No. Part No. Description
301 4-476-669-01 COVER (C (4531)), HINGE (BLACK)
301 4-476-669-11 COVER (C (4531)), HINGE (BROWN)
301 4-476-669-21 COVER (C (4531)), HINGE (WHITE)
302 1-889-187-11 FP-2193 FLEXIBLE BOARD (Note 2)
303 X-2585-820-2 HINGE (P) (Y (4071)) ASSY
304 1-471-573-11 MAGNET (Note 3)
305 4-476-554-01 COVER (M (4531)), HINGE
306 4-476-547-01 CABINET (M (4531)), P
307 4-476-551-01 KNOB (4531), FOCUS
308 4-476-548-01 PLATE (4531), PANEL GROUND
HDR-CX530E/CX535/CX610E/PJ530E/PJ540/PJ540E/PJ610E_L2
305
(Note 1)
#288
306
#2
304
(Note 3)
314
(Note 4)
(14 x 4.5 mm)
LCD901
309
310
311
Ref. No. Part No. Description
309 4-476-549-01 CUSHION (4531), LCD
310 4-527-288-01 SHEET (4531), PJ RADIATION
311 4-476-550-01 RETAINER (4531), LCD
312 4-476-552-01 INSULATING SHEET (4531), PD
313 A-2011-101-A PD-1031 BOARD, COMPLETE (SERVICE)
314 4-274-987-01 TAPE (AS 1/2) (C) (Note 4)
315 4-535-448-01 P CABINET M SHEET (4531)
LCD901 A-1992-237-A TP-LCD BLOCK ASSY (SZ814D)
#2 2-635-562-31 SCREW (M1.7)
#288 2-187-345-21 SCREW (M1.7), P2 (Note 1)
Screw
#2: M1.7 X 4.0 #288: M1.7 X 2.5
(Black)
2-635-562-31
1.7
4.0
Note
Note 1: This screw cannot be reused. Discard the screw removed
once in servicing.
Instead, use a new screw.
307
Note 2: Refer to "Assembly-1: The Method of attachment of FP-
2192/2193 Flexible Board".
Note 3:
Install the magnet with
the marking oriented
as shown below.
315
308 Marking
Note 4: Cut the TAPE (AS 1/2) (C) (Ref.No. 314) for specified size
and use it.
2-9
(Black)
2-187-345-21
1.7
2.5
Note 1: このねじは再利用することができません。
サービス対応時に一度でも外した場合は新品のねじと交換
してください。
Note 2: "Assembly-1: The Method of attachment of FP-2192/2193
Flexible Board" を参照してください。
Note 3: マグネッ トを取付ける
際は， マ−キング面を
図の位置にあわせて
ください。
マーキング
Note 4: TAPE (AS 1/2) (C) (Ref.No. 314) は, 指定の寸法にカットして
使用してください。