Table of Contents
Advertisement
2-1-4. LENS SECTION-2
169
165
(Note 5)
(Note 3)
169
(Note 5)
(Bosses)
169
169
(Note 5)
(Note 5)
#289
#278
(Note 1)
(Note 1)
152
169
(Note 5)
#278
#289
(Bosses)
(Note 1)
(Note 1)
#289
(Bosses)
169
M901
(Note 1)
151
(Note 5)
#290
#290
169
#289
(Note 1)
155
#289
(Note 1)
(Claw)
164
A
Ref. No.
Part No.
Description
151
4-436-061-01
SHEET METAL B (0020A)
152
4-439-875-01
MECHA_STOP RUBBER (0020A),
153
A-1903-090-A
CM-1004 BOARD, COMPLETE (Note 2)
154
4-436-438-01
BEARING (FLANGE NON), BALL
155
4-436-060-01
SHEET METAL A (0020A)
156
8-848-901-01
DEVICE, LENS LSV-1610B
157
4-436-733-01
RUBBER (1610), SEAL (Note 4)
158
4-436-063-01
SHEET METAL D-SUB (0020A)
159
4-436-065-01
FRAME E-SUB-A (0020A)
160
4-436-068-01
FRAME F-SUB-A (0020A)
161
1-889-183-11
FP-2189 FLEXIBLE BOARD (Note 3)
162
4-436-066-01
FRAME E-SUB-B (0020A)
163
4-436-069-01
FRAME F-SUB-B (0020A)
HDR-CX530E/CX535/CX610E/PJ530E/PJ540/PJ540E/PJ610E_L2
169
(Note 5)
#288
(Note 1)
167
166
(Note 3)
152
#278
(Note 1)
#278
A
(Note 1)
153
(including CP001 (CMOS
M902
imager)) (Note 2)
157
(Note 4)
#172
168
156
(Boss)
158
159
(Boss)
169
#278
(Note 1)
(Note 5)
161
#290
(Note 3)
154
162
169
#278
(Note 5)
(Note 1)
154
163
(Boss)
(Boss)
Ref. No.
Part No.
Description
164
4-436-070-01
ORNAMENT (0020A), FRONT
165
A-1919-696-A
FP-2125 FLEXIBLE BOARD, COMPLETE (Note 3)
166
A-1919-697-A
FP-2126 FLEXIBLE BOARD, COMPLETE (Note 3)
167
4-436-062-01
SHEET METAL C (0020A)
168
1-856-432-21
FILTER BLOCK, OPTICAL
169
4-441-672-01
SHEET, ADHESIVE (Note 5)
M901
1-855-222-11
MOTOR-A (0020A)
M902
1-855-223-11
MOTOR-B (0020A)
#172
2-178-410-01
TITE (UB TITE) 1.4
#278
4-423-712-01
SCREW, 0+P2 M2 NEW TRU-STAR (Note 1)
#288
2-187-345-21
SCREW (M1.7), P2 (Note 1)
#289
4-448-683-01
SCREW, 0+P2 M1.7 NEW TRU-STAR (Note 1)
#290
4-300-106-11
BTITE (1.4 (CH))
Screw
#172: M1.4 X 4.0 (Tapping)
(Black)
2-178-410-01
4.0
Note
Note 1: Machining for preventing screws from loosening is applied
to this screw.
If this screw is turned a few times or more, do not reuse it
and use a new one.
Note 2: Be sure to read "Precautions for Replacement of Imager"
on page 6-1 of Level 3 when changing the imager.
Note 3: When any of these Flexible Boards is peeled off and
decreased adhesive force of the Adhesive Part or wrinkle or
break of the Flexible Board is found, replace the defective
Flexible Board with a new one.
Note 4: Refer to "Assembly-3: How to distinguish the side of Optical
Filter Block facing to Lens Device".
Note 5: Cut the SHEET, ADHESIVE (4-441-672-01) as shown in the
balloon in the figure and use it.
160
#278
169
(Note 1)
(Note 5)
2-6
#288: M1.7 X 2.5
#278: M2.0 X 3.0
(Black)
(Pink)
2-187-345-21
4-423-712-01
1.4
1.7
2.0
2.5
3.0
Note 1: このねじは緩み防止加工が施されています。
Note 2: イメージャの交換時はLevel 3の6-1ページ，"イメージャ交
Note 3: これらのフレキシブル基板を剥がした場合に，粘着部の粘
Note 4: "Assembly-3: How to distinguish the side of Optical Filter
Note 5: SHEET, ADHESIVE (4-441-672-01) は図中の吹き出しのよう
#289: M1.7 X 2.5
#290: M1.4 X 5.0 (Tapping)
(Green)
(Black)
4-448-683-01
4-300-106-11
1.7
1.4
2.5
5.0
2 〜 3回以上外した場合は，再利用せず新品のねじを使用
してください。
換時の注意"を必ずお読みください。
着力の低下，フレキシブル基板のしわ，折れが認められた
場合は新品に交換してください。
Block facing to Lens Device"を参照してください。
に切って使用すること。
Advertisement
Table of Contents
