Sony DR-CX530E Service Manual page 12

(5) Set the Plate of the Motor A in the state shown in the figure and
install the Motor A matching it with the two bosses on the Sheet
Metal A, and then tighten three screws in the order shown in the
figure below.
Screw (A)
Tightening torque = 0.12 ± 0.02N · m (1.2 ± 0.2kg f · cm)
Screw (B)
Tightening torque = 0.18 ± 0.02N · m (1.8 ± 0.2kg f · cm)
Boss
T O
P
Motor A
Boss
2
Sheet Metal A
Screws
1
(B)
Screws
(A)
3
Screw
(B)
(6) Attach the Edge of Mechanical Rubber to the Sheet Metal B and
install the Sheet Metal B while matching it with the two bosses.
Tighten three screws in the order shown in the figure below.
Tightening torque = 0.18 ± 0.02N · m (1.8 ± 0.2kg f · cm)
P
T O
Sheet Metal B
Boss
Boss
Mecha Stop Rubber
1
HDR-CX530E/CX535/CX610E/PJ530E/PJ540/PJ540E/PJ610E_L2
(7) Stick the Adhesive Part of the Motor A Flexible Board while
matching it with the two bosses.
If the adhesive force is lowered, cut the Adhesive Sheet as shown
in the figure in the frame and then stick it.
Adhesive part
P
T O
Flexible Board of
the Motor A
Shape and sticking position
of Adhesive Sheet
Flexible Board of
the Motor A
(8) Install the Frame (E-SUB-A), Frame (E-SUB-B), and Ball Bear-
ing while matching the six bosses and the shaft with the holes, and
then tighten six screws in the order shown in the figure below.
Bosses
P
T O
Shaft
2
6
Bosses
3
5
Screws
Hole
Frame (E-SUB-B)
(9) Stick the Adhesive Part of the FP-2189 Flexible Board and the
Radiation Sheet while attaching the four bosses and connecting
the connector.
If the adhesive force is lowered, cut the Adhesive Sheet as shown
in the figure in the frame and then stick it.
Bosses FP-2189
Flexible Board
Adhesive
part
Adhesive part
FP-2189 Flexible Board
Bosses
T O
P
Frame (E-SUB-A),
Ball Bearing
2
Screws
1
4
Screws
3
1-8
(10) Set the Plate of the Motor B to the state shown in the figure and
attach the two bosses of the Motor B while matching them with
the holes in the Sheet Metal B, and then tighten three screws in
the order shown in the figure below.
Tightening torque = 0.18 ± 0.02N · m (1.8 ± 0.2kg f · cm)
T O
P
CM Radiation Sheet
Bosses
Connector
Shape and sticking position
of Adhesive Sheet
FP-2189 Flexible Board
Adhesive
part
(11) Install the Frame (F-SUB-A), Frame (F-SUB-B), and Ball Bear-
ing while attaching the four bosses and the shaft, and then tighten
Adhesive five screws in the order shown in the figure below.
part
Tightening torque = 0.18 ± 0.02N · m (1.8 ± 0.2kg f · cm)
Connector
Motor B
Boss
Shaft
Frame (F-SUB-B),
Ball Bearing
– ENGLISH –
2
Screws
1
Motor B 3
Bosses
P
T O
Screws
P
4
T O
5
Boss
Bosses
Frame (F-SUB-A)
Boss 3
2
1
Screws