Sony HDR-CX220 Service Manual page 27

2-1-9. CABINET (R) SECTION
(CX3[][] Model)
Refer to page 2-9 about PJ3[][] Model.
Refer to page 2-10 about PJ2[][] Model.
Refer to page 2-12 about CX2[][] Model.
#288
(Note 1)
411
412
(Claws)
413
(Note 3)
#11
#11
401
#2
(Claws)
402
403
(Claws)
(Claws)
Ref. No. Part No. Description
401 4-447-000-01 CABINET (C (415)), P (CX380/CX380E)
401 4-447-000-11 CABINET (C (415)), P (CX390 (BROWN))
401 4-447-000-21 CABINET (C (415)), P (CX390 (WHITE))
401 4-447-000-31 CABINET (C (415)), P (CX390 (PINK))
401 4-447-000-41 CABINET (C (415)), P (CX320/CX320E)
401 4-447-000-51 CABINET (C (415)), P (CX390 (BLACK)/CX390E)
402 4-274-987-01 TAPE (AS 1/2) (C)
403 A-1903-098-A PD-1013 BOARD, COMPLETE
404 4-446-971-01 INSULATING SHEET (4071)
405 4-446-972-01 RETAINER (415), LCD
406 4-446-976-01 CUSHION (415), LCD
407 4-446-967-01 PLATE (415), PANEL GROUND
408 4-446-964-01 CABINET (M (415)), P
409 4-446-960-01 COVER (M (409)), HINGE
HDR-CX220/CX220E/CX230/CX230E/CX280/CX280E/CX290/CX290E/CX320/CX320E/CX380/CX380E/CX390/CX390E/PJ220/PJ220E/PJ230/PJ230E/PJ320E/PJ380/PJ380E/PJ390/PJ390E_L2
414
#288
(Note 1)
409
#2
410
(Note 2)
LCD901
406
405
404
Ref. No. Part No. Description
410 1-471-573-11 MAGNET (Note 2)
411 X-2585-819-1 HINGE (Y (409)) ASSY, T TYPE
412 4-446-995-01 COVER (C (415)), HINGE (BLACK)
412 4-446-995-11 COVER (C (415)), HINGE (BROWN)
412 4-446-995-21 COVER (C (415)), HINGE (WHITE)
412 4-446-995-31 COVER (C (415)), HINGE (PINK)
413 1-887-312-11 FP-2068 FLEXIBLE BOARD (Note 3)
414 A-1909-320-A CABINET (R) ASSY (415)
LCD901 A-1910-211-A TP-LCD BLOCK ASSY (SZ814D)
#2 2-635-562-31 SCREW (M1.7)
#11 3-078-890-11 SCREW, TAPPING
#288 2-187-345-21 SCREW (M1.7), P2 (Note 1)
Screw
#2: M1.7 X 4.0 #11: M1.7 X 4.0 (Tapping)
(Black)
2-635-562-31
1.7
4.0
Note
Note 1: This screw cannot be reused. Discard the screw removed
408
once in servicing. Instead, use a new screw.
Note 2: Install the magnet with
the marking oriented
as shown below.
Marking
407
Note 3: Refer to "Assembly-1: Installation Method of FP-2055/FP-
2068.".
2-11
#288: M1.7 X 2.5
(Silver) (Black)
3-078-890-11 2-187-345-21
1.7 1.7
2.5
4.0
Note 1: このねじは再利用することができません。サービス対応時に
一度でも外した場合は新品のねじと交換してください。
Note 2: マグネットを取付ける
際は，マ−キング面を
図の位置にあわせて
ください。
マーキング
Note 3: "Assembly-1: Installation Method of FP-2055/FP-2068." を
参照してください。