Cabinet (R) Section - Sony HDR-CX220 Service Manual

2-1-5. CABINET (R) SECTION

(PJ3[][] Model)
Refer to page 2-8 about PJ2[][] Model.
Refer to page 2-11 about CX3[][] Model.
Refer to page 2-12 about CX2[][] Model.
ns: not supplied
#288
(Note 1)
206
#11
#2
(Claws)
203
(Claws)
201
(Claws)
202
Ref. No. Part No. Description
201 4-447-015-01 ORNAMENT (4071), PJ WINDOW (BLACK)
201 4-447-015-11 ORNAMENT (4071), PJ WINDOW (WHITE)
201 4-447-015-31 ORNAMENT (4071), PJ WINDOW (RED)
201 4-447-015-41 ORNAMENT (4071), PJ WINDOW (BROWN)
202 4-447-001-01 CABINET (C (4151)), P (PJ380/PJ380E (BLACK))
202 4-447-001-11 CABINET (C (4151)), P (PJ380/PJ380E (RED))
202 4-447-001-21 CABINET (C (4151)), P (PJ390/PJ390E (WHITE))
202 4-447-001-31 CABINET (C (4151)), P (PJ390 (BROWN))
202 4-447-001-41 CABINET (C (4151)), P (PJ320E)
202 4-447-001-51 CABINET (C (4151)), P (PJ380/PJ380E (WHITE))
202 4-447-001-61 CABINET (C (4151)), P (PJ390E (BLACK))
202 4-447-001-71 CABINET (C (4151)), P (PJ390E (RED))
203 4-272-357-01 GASKET (P (389))
204 4-460-223-01 SHEET (4151), PD PROTECTION
205 4-272-354-01 SHEET, P RADIATION
HDR-CX220/CX220E/CX230/CX230E/CX280/CX280E/CX290/CX290E/CX320/CX320E/CX380/CX380E/CX390/CX390E/PJ220/PJ220E/PJ230/PJ230E/PJ320E/PJ380/PJ380E/PJ390/PJ390E_L2
215
(Claws)
214
ns
211
(Note 2, 3)
210
213
(Note 2, 3)
(Note 2, 3)
207
212
Adjust the position.
(Note 2, 3)
209
(Note 2, 3)
208
(Claws)
#30
205
204
Ref. No. Part No. Description
206 4-446-978-01 HEAT SINK (4151), P
207 4-272-358-01 CUSHION, P
208 A-1903-100-A FP-2106 BOARD, COMPLETE
209 A-1847-133-A LSV-1580A (Note 2, 3)
210 4-298-764-01 COVER GLASS FRAME (1580) (Note 2, 3)
211 4-298-761-01 COVER GLASS (1580) (Note 2, 3)
212 4-298-774-01 F LEVER (1580) (Note 2, 3)
213 4-414-148-01 +Z TAPPING B1.2 (Note 2, 3)
214 A-1903-099-A PJ-1003 BOARD, COMPLETE
215 A-1909-321-A CABINET (R) ASSY (4151)
#2 2-635-562-31 SCREW (M1.7)
#11 3-078-890-11 SCREW, TAPPING
#30 3-086-156-11 SCREW B1.2
#288 2-187-345-21 SCREW (M1.7), P2 (Note 1)
Screw
#2: M1.7 X 4.0
(Black)
2-635-562-31
1.7
4.0
Note
LCD Section
(PJ3[][] model)
(See Page 2-9)
Note 1: This screw cannot be reused. Discard the screw removed
once in servicing. Instead, use a new screw.
Note 2:
PRECAUTIONS WHEN HOLDING THE PROJECTOR UNIT
Very weak
(Don't hold)
Lens part
Sheet
The projector unit (copper plate in particular) becomes hot after it is used.
When replacing a part of the projector unit, wait until it is cooled down.
Note 2:
プロジェクターユニットを持つ際の注意
非常に弱い
(持ってはいけない)
レンズ部
シート
プロジェクターを使用した後は，プロジェクターユニットが熱くなっています。
特に銅板の部分は高温になります。
部品を交換する時は，温度が下がってから作業を行なってください。
Note 3: When this part is replaced, adjustment values must be
written.
Perform Projector Data Input from the Adjust manual.
2-7
#11: M1.7 X 4.0 (Tapping) #30: M1.2 X 3.5 (Tapping) #288: M1.7 X 2.5
(Silver) (White)
3-078-890-11 3-086-156-11
1.7 1.2
3.5
4.0
Note 1: このねじは再利用することができません。サービス対応時
に一度でも外した場合は新品のねじと交換してください。
Have to wear
Weak
finger stall
(Handling attention)
Contact area of
Lever
Copper Plate
Flexible Board
Terminal of
Copper Plate
Connector
弱い 指サック着用
(取り扱い注意) のこと
レバー
フレキ接点
銅板
コネクタ部
銅板
Note 3: この部品を交換した場合、調整値の書き込みが必要です。
Adjust manualからProjector Data Inputを実施してくださ
い。
(Black)
2-187-345-21
1.7
2.5