Subscribe to Our Youtube Channel
Related Manuals for Dante DLW5600
Summary of Contents for Dante DLW5600
- Page 1 DLW56-57-58-5900 Digital Video Recorder Installation and Operations Manual Model Number: DLW5600-DLW5700-DLW5800-DLW5900 Description: Digital Video Recorder...
- Page 2 Digital Video Recorder User Manual CAUTION Please read this user manual carefully to ensure that you can use the device correctly and safely This manual is suitable for 4-channel, 8-channel and 16-channel series DVR. In this book, we take 200FPS 8-channel DVR as a sample.
-
Page 3: Table Of Contents
Digital Video Recorder User Manual Table of Contents CHAPTER 1 Introduction ................................. 1 1.1 DVR Introduction ................................1 1.2 Main Features ..................................1 CHAPTER 2 Hardware Installation ............................4 2.1 Install Hard Drive &DVD Writer ............................4 ... - Page 4 Digital Video Recorder User Manual 4.2 Main Menu Setup................................43 4.2.1 Basic Configuration ......................................45 4.2.2 Live Configuration ......................................46 4.2.3 Record Configuration ....................................... 47 4.2.4 Schedule Configuration ....................................49 4.2.5 Alarm Configuration ......................................49 ...
- Page 5 Digital Video Recorder User Manual 7.1 By Phones with WinCE ..............................88 7.2 By Phones with Symbian ..............................92 FAQ ................................... 96 Appendix A Appendix B Calculation of Recording Capacity ........................100 Compatible Devices ............................
- Page 6 HDD installation DLW5400-5500-5600-5700AL 1. Loosen the screws and open the top case. 2. Loosen the power and SATA cables.
- Page 7 3. If you have 3 or 4 HDD, please install HDD on the lower layer of the HDD stand as below first. Notice: It is not necessary to remove the top bracket. There are the related holes for screwdriver on the upper stand. 4.
- Page 8 5. Then install other HDD on the upper layer as above. 6. Place the top cover back and tighten the screws. 7. Power on the unit. If it detect the HDD, it will show below information on the screen once entering the system.
- Page 9 8. Enter Menu---System---TOOLS---Disk manager. Choose the HDD one by one and click...
-
Page 10: Chapter 1 Introduction
Digital Video Recorder User Manual Introduction CHAPTER 1 1.1 DVR Introduction This model DVR (Digital Video Recorder) is designed specially for CCTV system. It adopts high performance video processing chips and embedded Linux system. Meanwhile, it utilizes many most advanced technologies, such as standard H.264 with low bit rate, Dual stream, SATA interface, VGA output mouse supported, IE browser supported with full remote control, mobile view(by phones), etc., which ensure its powerful functions and high stability. - Page 11 Digital Video Recorder User Manual BACKUP • Support USB 2.0 devices to backup • Support built-in SATA DVD writer to backup • Support saving recorded files with AVI standard format to a remote computer through internet RECORD & PLAYBACK • Record modes: Manual, Schedule, Motion detection and Sensor alarm recording •...
- Page 12 Digital Video Recorder User Manual SECURITY • Two level user group management: advance and normal, rights authorized by administrator • Support 1 administrator and 15 users. • Support event log recording and checking, events unlimited NETWORK • Support TCP/IP, DHCP, PPPoE, DDNS protocol •...
-
Page 13: Chapter 2 Hardware Installation
Digital Video Recorder User Manual Hardware Installation CHAPTER 2 Notice: Check the unit and the accessories after getting the DVR. Please disconnect the power before connected to other devices. Do not hot plug in/out 2.1 Install Hard Drive &DVD Writer 2.1.1 Install Hard Drive Notice: 1. - Page 14 Digital Video Recorder User Manual Fig 2.1 Front Panel Item Name Function Multi-screen button Change screen display like single, 4, 8 ,and 16 screens Input number 10 and the above number together with other digital keys. MENU Enter menu in live BACKUP Enter backup mode in live P.T.Z...
-
Page 15: Rear Panel Instructions
Digital Video Recorder User Manual Fast forward IR receiver For remote controller SEARCH Enter search mode Record manually Power Power on/off To connect external USB devices for backup or update firmware（Can not USB port connect to mouse） Digital keys Input digital number or select the number of camera Indicators Working indicators of power and network, etc. - Page 16 Digital Video Recorder User Manual Item Name Description Connect to monitor as an AUX output channel by channel. Only video display, no SPOT OUT menu show AUDIO OUT Audio output, connect to the sound box S-VIDEO S-Video output, connect to monitor PS/2 port Connect to PS/2 mouse USB MOUSE...
- Page 17 Digital Video Recorder User Manual Fig 2.3 Rear Panel (2) for 8-channel DVR Item Name Description Connect to monitor as an AUX output channel by channel. Only video display, no menu Spot out show Audio out Audio output, connect to the sound box S-VIDEO S-Video output, connect to monitor MIC IN...
- Page 18 Digital Video Recorder User Manual Item Name Description ALARM OUT Relay output1-4. Connect to external alarm. +5V and GND +5 V and Grounding AUDIO IN Audio input form 1-8 channels For cooling the device POWER INPUT AC 110Vor 110V POWER SWITCH Switch on/off LOOP OUT For outputting each channel’s image independently...
-
Page 19: Remote Controller
Digital Video Recorder User Manual Item Name Description Connect to monitor as an AUX output channel by channel. Only video display, no menu Spot out show Audio in 16 CH Audio input Audio out Audio output, connect to the sound box S-video S-Video output, connect to monitor MIC IN... - Page 20 Digital Video Recorder User Manual Notice: Frequently defect checking as following 1. Check batteries poles 2. Check the remaining charge in the batteries 3. Check IR controller sensor is mask If it doesn't still work, Please change a new remote controller to try, or contact your dealers The interface of remote controller is shown in Fig 2.5 Remote Controller.
-
Page 21: Control With Mouse
Digital Video Recorder User Manual Item Name Function Power Button Soft switch off to stop firmware running. Do it before power off. INFOR Button Get information about the DVR like firmware version, HDD information REC Button To record manually Digital Button Input digital or choose camera Multi Screen Button To choose multi screen display mode... - Page 22 Digital Video Recorder User Manual In setup: Click left button to enter. Click right button to cancel setup, or return to the previous. If want to input the value, move cursor to the blank and click. A input window will appear as Fig. 12. It supports digitals, letters and symbols input.
-
Page 23: Chapter 3 Basic Function Instructions
Digital Video Recorder User Manual Basic Function Instructions CHAPTER 3 3.1 Power On/Off Notice: Before you power on the unit, please make sure all the connection is good. 3.1.1 Start There are two ways to start this DVR. One way is to Connect with the source power, switch on the power button near the power port in the rear panel, and the system will be loaded. - Page 24 Digital Video Recorder User Manual Fig 3.2 Preview...
- Page 25 Digital Video Recorder User Manual Symbol Meaning Symbol Meaning Enable audio in live Disable audio in live Manual record Timer record (green) (blue) Motion detection record Alarm record (yellow) (red) Current working HDD Space Size of current HDD Free Free space of current USB devices connected HDD full 3.1.2 Close...
-
Page 26: Login &User Management
Digital Video Recorder User Manual Choose OK to enter. The unit will power off automatically after a while STEP2 Disconnect the power STEP3 By front panel or mouse: Press ENTER button or click right mouse to show menu bar, referring to Fig 4.1 Control Bar. STEP1 Click Shut down button, referring to Fig 3.3 Shut down STEP2... - Page 27 Digital Video Recorder User Manual Notice: The default is admin and 123456. Change password: Every one can change his own password. In login state, click Log in/out on the control bar. A window will appear with two options. One is for logout, STEP1 another for password modification.
- Page 28 Digital Video Recorder User Manual Press right mouse to show the control bar. Enter Menu---->System. Enter USER configuration. Click Add button, please see Fig 3.6 Add User. STEP1 Fig 3.6 Add User Input user name and password. Choose the user group. STEP2 Click OK button to add a new user STEP3...
-
Page 29: Recording
Digital Video Recorder User Manual Click OK button to delete the user STEP6 Notice: illumination of users’ rights Administrator: have all rights to do every thing. Advance: do others except entering USER to manage users Normal: do others except entering SYSTEM to change the settings. The user name and password are the combination of digitals, letters, or symbols. -
Page 30: Manual Recording
Digital Video Recorder User Manual Fig 3.7 Record Setup Set Video quality, Frame rate, and Resolution. STEP2 Have Audio checked if you input audio and want to record. Check Time stamp to record. STEP3 Enable recording function for cameras in Record option. STEP4 Notice: If having camera unchecked here, it will not record in any recording mode. -
Page 31: Schedule Recording
Digital Video Recorder User Manual 3.3.3 Schedule Recording Users can set different schedule time for every day in one week. If you want a special schedule for one day, you can use Holiday function. Enter SCHEDULE configuration. Select Channel and Schedule; please see Fig 3.8 Schedule Setup. STEP1 Fig 3.8 Schedule Setup The volume means the 7 days of one week. -
Page 32: Motion Detection Recording
Digital Video Recorder User Manual Fig 3.9 Calendar Select the date and set the schedule time. If want to delete this special schedule, click Delete button STEP4 Click OK button to finish STEP5 Then the DVR will auto record once it goes to the time you set. 3.3.4 Motion Detection Recording This unit supports recording channels and PTZ linking. - Page 33 Digital Video Recorder User Manual Fig 3.10 Motion Detection Setup Enable Detection first. Enter Area to set Sensitivity and detection Area. In detection area, red means unchecked, STEP2 transparence means available, see Fig 3.10 Motion Detection Area Setup. Due to the sensitivity is influenced by the color and time (day or night), users can adjust its value according to the practical condition.
- Page 34 Digital Video Recorder User Manual Fig 3.10 Motion Detection Area Setup Enter Trigger configuration, see Fig 3.11 Alarm Out Setup STEP3 Fig 3.11 Alarm Out Setup...
-
Page 35: Alarm Recording
Digital Video Recorder User Manual Select alarm out and recording channels. It can trigger any alarm out and cameras to record once motion STEP4 detected. Enable or disable Buzzer on board. Select speed dome and enable preset or auto cruise. Press OK to save STEP5 Set Hold time. -
Page 36: Playback
Digital Video Recorder User Manual Fig 3.12 Sensor Alarm Setup Enable Detection first. Set Device type. STEP2 Enter Trigger configuration. Set alarm out, recording cameras and linked PTZ, referring to 3.3.4 Motion STEP3 Detection Recording STEP4-5 Set Alarm in hold time. It is the interval time between the two adjacent efficient alarms. This is similar with Hold STEP4 time in MOTION configuration. - Page 37 Digital Video Recorder User Manual Fig 3.13 Search Menu Time search: Enter Search configuration, select Time search. A window will appear as Fig 3.14 Calendar Search. If it STEP1 recorded in a day, the date will show highlight.
- Page 38 Digital Video Recorder User Manual Fig 3.14 Calendar Search Choose a day to time search interface, as Fig 3.15 Time Search. STEP2...
- Page 39 Digital Video Recorder User Manual Fig 3.15 Time Search This unit has full and 4 screen playback. Select the screen display mode and the channels. STEP3 If want to change the date, press Date button. Set hour and minutes of start time. If it recorded at that time, the STEP4 boxes will show green.
- Page 40 Digital Video Recorder User Manual Fig 3.16 Playback Event search: Enter Search---->Event search. The calendar window will appear as that of time search STEP1...
-
Page 41: Backup &View
Digital Video Recorder User Manual Choose a day in event search interface, as Fig 3.17 Event Search STEP2 Fig 3.17 Event Search Choose camera and event type, motion or sensor. STEP3 Double click one video file to play. STEP4 3.5 Backup &View This unit supports backup by built-in SATA DVD Writer with USB Flash, through the USB port on the front panel. - Page 42 Digital Video Recorder User Manual Fig 3.18 Backup Setup Choose the channel, and set the start and end time. Click Date button to change the date. STEP2 Enable “Attach record player,” it will save a special player simultaneously when backup. With this player, users STEP3 can make time search and event search when checking the backup.
- Page 43 Digital Video Recorder User Manual Fig 3.19 Backup Information Notice: If users install built-in DVD writer and USB device, it will show USB device in previous. It will show CD-ROM even though users install DVD writer Press OK button. It will begin to write video from HDD inside DVR to backup device, and show the process as STEP5 below.
- Page 44 Digital Video Recorder User Manual Check &View: The steps to view the backup with the special software are as following: Remove the backup device to a computer. Enter the backup folder and open video play。The backup viewer as STEP1 shown as Fig 3.20 Click Browse to choose the folder, which contains the video backup, as Fig 3.21 Choose Backup Folder.
- Page 45 Digital Video Recorder User Manual Fig 3.20 Backup Player...
- Page 46 Digital Video Recorder User Manual Fig 3.21 Choose Backup Folder Set the date and channels. It will show the recorded video in below area with green light at the bottom as shown STEP4 in Fig 3.22 Backup Data Search. Fig 3.22 Backup Data Search It supports AVI converter.
- Page 47 Digital Video Recorder User Manual Drag the slide bar to the start time point, click play button to view. STEP6 Click icon a conversion AVI window will appear as shown as Fig 3.23. Click Conversion button, it will STEP7 Start converting the files and the process will show at the bottom. Fig 3.23 Conversion AVI Select the files.
- Page 48 Digital Video Recorder User Manual The function and definition of buttons as shown as Table 3.1 Fig 3.24 Play backup file...
-
Page 49: Ptz Control
Digital Video Recorder User Manual Index Definition Index Definition Index Definition Index Definition Index Definition ① Open file ② Open disk ③ Full ④ Snap picture Convert video ⑤ screen file into AVI Pause Stop Play Forward/Rewind Screen mode ⑥ ⑦... - Page 50 Digital Video Recorder User Manual Select a preset and click Save to a preset. Users can set 128 presets totally. Fig 3.24 Set Presets Click Set button at right of Cruise. Here users can set cruise track, as Fig 3.25 Set Cruise. Choose the preset, STEP4 set stay time of every preset.
- Page 51 Digital Video Recorder User Manual Select a preset in left preset list, click – button to delete the preset. Click ↑,↓,↑,↓ to adjust the sequence of STEP5 the presets in the auto cruise. Click Save to save and return to the previous interface. Click button to save and exit.
-
Page 52: Menu Setup Guide
Digital Video Recorder User Manual Menu Setup Guide CHAPTER 4 4.1 Menu Navigation Menu Option Menu Option Device name &ID Camera name Video format Camera mask Language Basic Live Name &time switch Date &time setup SPOT out switch Live audio switch Color adjustment Authorization check switch Video quality... -
Page 53: Main Menu Setup
Digital Video Recorder User Manual Recorded cameras and PTZ linking Recorded cameras and PTZ linking HTTP &server ports Protocol, baud rate and address IP address setup Speed setup Network PPPoE Presets setup Network video setup Cruise setup DDNS Add users Disk manager User Delete users... - Page 54 Digital Video Recorder User Manual Fig 4.2 Up-listed Menu Select System. A graphic user interface will show as Fig 4.3 System Setup. Fig 4.3 System Setup...
-
Page 55: Basic Configuration
Digital Video Recorder User Manual Press MENU button on the front panel or remote controller. The interface above will also appear. Notice: Only administrator and advance user can enter system setup and do setup. It need reboot after some parameters changed, like video format. 4.2.1 Basic Configuration Click BASIC to enter basic configuration as Fig. -
Page 56: Live Configuration
Digital Video Recorder User Manual this. Audio: enable audio in live. Users can choose a random channel. Date format: three formats, YY-MM-DD, DD-MM-YY, MM-DD-YY. System time: set the time. If the unit is recording, users cannot change the time. When recording, click Adjust button, a security window will appear. -
Page 57: Record Configuration
Digital Video Recorder User Manual auto dwell and spot out. SPOT enable: enable spot output. Color: Click Set button, a window will appear as Fig 4.6 Color Adjustment. Fig 4.6 Color Adjustment Adjust Brightness, Hue, Saturation, and Contrast in live here. Default: set the color to the default value. - Page 58 Digital Video Recorder User Manual Fig 4.7 Record Configuration Here users can set record quality, frame rate, resolution, and recycle. The following are the definitions of every option. Video quality: it has five options from lowest to highest. The higher the value is, the clearer the recorded picture is. Frame rate: set recorded frame rate.
-
Page 59: Schedule Configuration
Digital Video Recorder User Manual 4.2.4 Schedule Configuration Click SCHEDULE to enter schedule configuration as Fig 4.8 Schedule Configuration. Fig 4.8 Schedule Configuration Here users can set schedule for timer, motion detection, and sensor alarm respectively. The following are the definitions of every option Always, Motion and Sensor: refer to record schedule, motion schedule and alarm schedule respectively. - Page 60 Digital Video Recorder User Manual Fig 4.9 Alarm Configuration Here users can set sensor type, alarm trigger and alarm time. The following are the definitions of every option. Device type: NC and NO (Normal Close and Normal Open). Set the value according to the alarm signal level of the sensors.
-
Page 61: Motion Configuration
Digital Video Recorder User Manual Fig 4.10 Alarm Out Configuration Alarm out: set relay alarm out channel. You can select any alarm channels. To record: set recording channels. You can select any record channels. It will record the cameras you choose here when alarm triggered. - Page 62 Digital Video Recorder User Manual Fig 4.11 Motion Configuration Here users can set motion sensitivity, detection area, and alarm out. The following are the definitions of every option. Enable: enable motion detection. Trigger: setup similar with that of sensor alarm. Nevertheless, linked speed domes must be different front current channel. I.e.
-
Page 63: Network Configuration
Digital Video Recorder User Manual Fig 4.12 Detection Area Configuration Sensitivity: set detection sensitivity from 1-8. The default is 4. Exit: quit without saving Holding time(S): the interval time between the two adjacent efficient motions, similar with that of sensor alarm. 4.2.7 Network Configuration Click NETWORK to enter network configuration as Fig 4.13 Network Configuration. - Page 64 Digital Video Recorder User Manual Fig 4.13 Network Configuration This unit supports DHCP, PPPoE, and DDNS. Users enable network function, and configure IP address, DDNS, transmission video parameters here. The following are the definitions of every option. HTTP port: the default is 80. If users change the value, they need add the port number when typing IP address in IE address blank.
-
Page 65: Configuration
Digital Video Recorder User Manual User name, Password: account information of PPPoE. Input what you get from your ISP. Click DDNS, a window will appear as Fig 4.14 DDNS Configuration. Now it supports DNS2P and 88IP. Users need register at www.dns2p.com www.88IP.net or www.meibu.com then input registers ID and password here. - Page 66 Digital Video Recorder User Manual Fig 4.15 Network Video Configuration Video quality: network picture quality. Frame rate: it has 3 options, 1, 2 and 3 fps. Resolution: now it only has CIF. Time stamp: Time displayed in the image. 4.2.8 P.T.Z Configuration Click P.T.Z to enter PTZ configuration as Fig 4.16 PTZ Configuration.
- Page 67 Digital Video Recorder User Manual Fig 4.16 PTZ Configuration Here users can set protocol, baud rate, address, presets, and auto cruise track here. The following are the definitions of every option. Protocol, Baud rate, Address: please set the value according to the settings of the speed dome. Speed: set the speed of speed domes.
-
Page 68: User Configuration
Digital Video Recorder User Manual Fig 4.17 Set Presets Cruise, Name: select a cruise track and rename it. Click Set in Cruise row. A window will appear as 3.6 PTZ Control. Notice: It has 128 presets and 32 cruise tracks totally 4.2.9 User Configuration Click USER to enter user management interface as Fig 4.18 User Configuration. -
Page 69: Tools Configuration
Digital Video Recorder User Manual Administrator can add, delete users, and change their authorization. Please refer to 3.2 Login &User Management. Notice: It supports one administrator and max 15 users. 4.2.10 Tools Configuration Click TOOLS to enter tools configuration as Fig 4.19 Tools Manager. Fig 4.19 Tools Manager Disk manager: please refer to 5.1 Format Hard Disk. -
Page 70: Chapter 5 Manage Dvr
Digital Video Recorder User Manual CHAPTER 5 Manage DVR 5.1 Format Hard Disk If wanting to record, it is necessary to format the hard disk at first. If not being formatted, it will show the position of the disk, free space, and total space show 0M at the bottom of screen. Enter TOOLS configuration, referring to 4.2.10 Tools Configuration. -
Page 71: Update Firmware
Digital Video Recorder User Manual If a disk has never been formatted, Status will show “new”. Select hard disks, press Format button to begin. STEP2 A security window will remind user that this will delete all data on HDD. Press OK to continue. A process will STEP3 display on the screen as below. -
Page 72: Check System Information
Digital Video Recorder User Manual Fig 5.2 Reset Blocks Enter TOOLS configuration, referring to 4.2.10 Tools Configuration. STEP1 Click Load default. Select setup blocks; please refer to Fig 5.2 Reset Blocks. STEP2 Press OK to do default. It will return to TOOLS interface after finished. STEP3 5.4 Check System Information Users can check system information like firmware version, IP address, etc. - Page 73 Digital Video Recorder User Manual Fig 5.3 Status Interface Click System, the window below will display. Check firmware version, recording parameters here. STEP3 Fig 5.4 System Information.
-
Page 74: Check System Log
Digital Video Recorder User Manual Return to the previous interface, and click Network. The window below will display. Check IP address, DVR Mac STEP4 address, network video quality. Fig 5.5 Network Information. 5.5 Check System Log This unit supports system log. It records its working state and operation automatically. Moreover, it divides the record into two groups: events and operation. - Page 75 Digital Video Recorder User Manual Fig 5.6 Events LOG Click Date to change date by a calendar. Click Type to select the event type. Then click Search button. It will STEP2 refresh the event list. Click ←, ←, →, → to do pgdn or pgup STEP3 Click right mouse to return to the previous interface.
-
Page 76: Check On-Line Network Users
Digital Video Recorder User Manual The operating is similar with searching events log. STEP5 Notice: The log files saved to the HDD inside. If HDD not installed, it will not record any thing. The number of log files is unlimited. 5.6 Check On-line Network Users Press right mouse to show the control bar. - Page 77 Digital Video Recorder User Manual Fig 5.9 File Manager Click Date to change date by a calendar, click Search to refresh the list. The files found will be listed in the file STEP3 area of file manager at bottom. It shows the details of every file, like start/end time, lock state. Select the files and click Lock, it will lock the selected files.
-
Page 78: Chapter 6 Remote Surveillance
Digital Video Recorder User Manual CHAPTER 6 Remote Surveillance 6.1 Accessing DVR If making remote view, the DVR must connect with LAN or internet. Then enable network server in the unit. Please refer to 4.2.7 Network Configuration. This unit supports IE browser, not any client software installed. In addition, it supports XP and Vista. 6.1.1 On LAN Input IP address, Subnet, Gateway. - Page 79 Digital Video Recorder User Manual Fig 6.1 View with IE browser...
-
Page 80: On Wan
Digital Video Recorder User Manual Notice: If HTTP port is not 80, other number instead, need add the port number after IP address. For example, set HTTP port as 82, need input IP address like 192.168.0.25:82. User name and password here are the same with that used on the DVR. The default is admin and 123456. 6.1.2 On WAN There are two ways that the DVR is connected to internet. - Page 81 Digital Video Recorder User Manual Fig 6.2 Remote Preview Interface...
- Page 82 Digital Video Recorder User Manual ① Full screen, 1/4/8 screens display mode. ② Camera indicators: ③ Picture snapshot ④ Remote preview: adjust the color of cameras and control PTZ. ⑤ Remote playback and backup: make remote playback and backup, check system log and journal. Please refer to 6.3 Remote Playback &Backup.
- Page 83 Digital Video Recorder User Manual Fig 6.3 Preview Snap Select frames captured one time. Enable Title and Time, it will capture title and time simultaneously. STEP2 Click Snap to capture pictures. STEP3 Click Browse to set saving path. Click Save to save pictures to HDD on the computer. And the saving folder STEP4 window will pop up.
- Page 84 Digital Video Recorder User Manual PTZ control: Click P.T.Z to enter the interface as below. Click on a channel to select the speed dome. Fig 6.4 Remote PTZ control...
- Page 85 Digital Video Recorder User Manual ① Move the speed dome. ② Stop adjustment. ③ Adjust zoom, focus, Iris, Speed. ④ Go to the preset. Click to rename the preset. ⑤ Select and do auto cruise. Click right mouse, a pull-down menu will appear as below. Fig 6.5 Preview Control Menu Full screen: the picture will fill the screen, without tools bar display.
-
Page 86: Remote Playback &Backup
Digital Video Recorder User Manual Fig 6.6 Set Cruise Click Add to add presets for the selected cruise. Click the preset, a down list menu will pop up. Users can select presets to add. Double click Time to set display time in auto cruise. Click Delete or Clear all to delete the presets. Click OK to save and exit. - Page 87 Digital Video Recorder User Manual Fig 6.7Remote Playback &Backup Interface This DVR supports remote time search, event search and one channel playback. The above is the default interface after entering Playback &Backup block. By time search: Select the date in calendar area①, select the channel in channel area②. STEP1...
- Page 88 Digital Video Recorder User Manual Click Search button to update the search result. All the recorded found will display in video data area③. STEP2 In area③, the top bar refers to hours and minutes in a day. The left column refers to cameras. Drag the slide bar STEP3 to a time point.
- Page 89 Digital Video Recorder User Manual Users can make fast forward/backward, pause, stop playback and snap pictures. About snap feature, it is the STEP5 same as that in remote preview, referring to Fig 6.3 Preview Snap. Click to return to search interface. STEP6 By event search: Click Event search, the window will display as below.
-
Page 90: Remote Backup
Digital Video Recorder User Manual Select a event, and click Play button to do remote playback. The following steps are the same as SETP5-6 of STEP3 time search above. 6.3.2 Remote Backup Users can download the recorded files from the DVR through network. Click Backup to enter the interface as below. Fig 6.10 Remote Backup Interface Select the date, channel. -
Page 91: Remote Menu Configuration
Digital Video Recorder User Manual Select files in left file area. Holding shift button, you can select multi files with mouse simultaneously. STEP3 Click Backup to do remote backup. It will show the process on the bottom of the screen as below. STEP4 Notice: the backup file is AVI format. - Page 92 Digital Video Recorder User Manual Fig 6.11 Remote Menu Setup The sub menu lists and the options in every sub menu are similar with those on the DVR. Please refer to 4.2 Main Menu Setup to do setup. Click Save to save the change. Some changes may pop up a dialog box as below and need restart.
-
Page 93: Remote Dvr Management
Digital Video Recorder User Manual 6.5 Remote DVR Management 6.5.1 Check System Log Remotely Users can check system log remotely. About the details of system log, please refer to Tab 5.1 Details of System Log. Click Search---->Log, the window below will appear. Event log search is the default interface. STEP1... - Page 94 Digital Video Recorder User Manual Fig 6.12 Remote System LOG Search Select the date, channel and event type. Then click Search. STEP2 The entire log found will list in left area. STEP3 Click Operation to enter operation Log search interface STEP4...
-
Page 95: Lock &Delete Files Remotely
Digital Video Recorder User Manual Fig 6.13 Remote Operation Log Search Select the date and click Search. It will list all the log files in the day in left area. STEP5 6.5.2 Lock &Delete Files Remotely Users can lock and delete video files through network. About the details of this feature please refer to 5.7 Lock &Delete Files. - Page 96 Digital Video Recorder User Manual Fig 6.14 Remote File manager Select date and channels, and then click Search. All the files found will list in the day in left area. STEP2 The relative status will show “Lock” if the file is locked. “Writing” means the file is still being written. STEP3 Select the files that is unlocked, click Delete.
-
Page 97: Chapter 7 Mobile Surveillance
Digital Video Recorder User Manual Mobile Surveillance CHAPTER 7 This DVR supports mobile surveillance by PDA or smart phones with WinCE and symbian OS. At the same time, it supports 3G network. Below are the details of the compatible OS version. Please check the symbian version information before using mobile view. - Page 98 Digital Video Recorder User Manual Symbian S60 1st Edition-Symbian OS v6.1 supported Symbian S60 2nd Edition-Symbian OS v7.0s supported Symbian S60 2nd Edition with FP1-Symbian OS supported v7.0s enhanced Symbian S60 2nd Edition with FP2-Symbian OS supported v8.0a Symbian S60 2nd Edition with FP3-Symbian OS supported v8.1 Symbian S60 3rd Edition-Symbian OS v9.1...
- Page 99 Digital Video Recorder User Manual Click on the software name. A dialog box pops up: STEP2...
- Page 100 Digital Video Recorder User Manual Click “Yes” to start downloading and installing: STEP3 PCam will be opened automatically after installed STEP4 Input the server’s address, ID and password respectively in the columns of “Server”, “User” and “Password”, STEP5 and click “Go” to log on the server. It will show the picture if access successfully.
- Page 101 Digital Video Recorder User Manual Camera one is the default channel after login. Change the channel in rolling-down menu of “Channel”: STEP6...
- Page 102 Digital Video Recorder User Manual Notice: User name and password here are the same with that used on the DVR. The default is admin and 123456. 7.2 By Phones with Symbian Please use the smart phones with symbian version supported by this unit. Firstly enable the network access on mobile phone.
- Page 103 Digital Video Recorder User Manual A security windows will pop up after downloading and ask if install the package. Click YES to install. STEP4 A Scam shortcut icon appears on the system menu after finished. STEP5 Run Scam program. It will enter a function interface. STEP6 Live view: to do mobile live view Image view: to check the pictures snapped in live view...
- Page 104 Digital Video Recorder User Manual Click System setting--->Login Setting to enter login interface. STEP7 Input the server’s address, ID and password respectively. And then save. STEP8 Notice: About Access point, there may be different access points in different countries or from service providers.
- Page 105 Digital Video Recorder User Manual Enter Live View, it will connect the server and display pictures. STEP9 Notice: User name and password here are the same with that used on the DVR. The default is admin and 123456. STEP10 In Live View, users can do snapshot, change channels and control PTZ.
- Page 106 Digital Video Recorder User Manual Appendix A Q1. Why the DVR cannot start after connected to the power? a. The adapter damaged. Please change an adapter b. The power of the adapter is not enough. Please remove the HDD to check c.
- Page 107 Digital Video Recorder User Manual c. HDD is full and not enables recycle function. Please refer to 4.2.3 Record Configuration. Chang a new HDD or enable recycle. d. The HDD damaged. Change a new one. Q6. Cannot use mouse. a. wait 5 minutes after mouse connected. b.
- Page 108 Digital Video Recorder User Manual Fig 7-2 Fig 7-3 ④ Then click ok to finish setup. b. Other plug-ins or anti-virus block activeX. Please uninstall or close them. Q8: How to deal with when DVR starts, it displays “please wait…”all the time First possible reason: hard-disk cable and data cable are not well connected.
- Page 109 Digital Video Recorder User Manual working, please unplug them and then try re-plugging again; Second possible reason: It is forced to stop because hard disk has disabled track which causes the system checking hard disk cannot skip Solution: Change another new hard disk or reformat the broken one Q9: The mouse inserting into the front USB jack does not work Hereby the front USB jack is only for backup of U disk, USB DVD writer etc., and not support USB mouse.
- Page 110 Digital Video Recorder User Manual Appendix B Calculation of Recording Capacity Users can calculate the size of hard disk according to the saving time and DVR recording settings. The DVR uses fixed video bit rate. The below are the details at different settings DVR. Farm Rate Totally Bit Rate Used Space...
- Page 111 Digital Video Recorder User Manual Appendix C Compatible Devices 1. Compatible USB drive after test Brand Capacity Netac Kingston Aigo Smatter vider Scandisk 512MB, 1G, 2GB Tab C.1 Compatible USB drive Compatible SATA CD/DVD writers after test Brand Model SAMSUNG TS-H653B LITEN-ON DH-20A6S01C...
- Page 112 Digital Video Recorder User Manual Appendix D DVR Specifications for 4-channel DVR Compression format Standard H.264 Baseline Video output Composite：1.0V p-p/75Ω，BNC×2 S-VIDEOX1, VGAX1 Video input Composite：1.0V p-p/75Ω，BNC×4 Display Resolution 720*576 (PAL), 720*480 (NTSC) Record Resolution 704*576 (PAL), 704*480 (NTSC) Display Frame Rate 100FPS (PAL), 120FPS (NTSC) Record Frame Rate 100FPS (PAL) , 120FPS (NTSC)
- Page 113 Digital Video Recorder User Manual Appendix E DVR Specifications for 8-channel DVR Compression format Standard H.264 Baseline Video output Composite：1.0V p-p/75Ω，BNC×2 S-VIDEOX1, VGAX1 Video input Composite：1.0V p-p/75Ω，BNC×8 Display Resolution 720*576 (PAL), 720*480 (NTSC) Record Resolution 704*576 (PAL), 704*480 (NTSC) Display Frame Rate 200FPS (PAL), 240FPS (NTSC) Record Frame Rate...
- Page 114 Digital Video Recorder User Manual Appendix F DVR Specifications for 16-channel DVR Compression format Standard H.264 Baseline Video output Composite：1.0V p-p/75Ω，BNC×2 S-VIDEOX1, VGAX1 Video input Composite：1.0V p-p/75Ω，BNC×16 Display Resolution 720*576 (PAL), 720*480 (NTSC) Record Resolution 704*576 (PAL), 704*480 (NTSC) Display Frame Rate 400FPS (PAL), 480FPS (NTSC) Record Frame Rate 400FPS (PAL) , 480FPS (NTSC)
Need help?
Do you have a question about the DLW5600 and is the answer not in the manual?
Questions and answers