Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for WELDTECH WT40DC
Summary of Contents for WELDTECH WT40DC
- Page 1 WT40DC 40A PLASMA CUTTER OPERATING INSTRUCTIONS www.weldtech.net.nz...
- Page 2 Designed for discerning operators who seek professional results and product quality without the price tag of a full professional setup. Design emphasis is placed on simple, functional design and operation. Weldtech product is subject to stringent quality control and designed and manufactured to NZ & Australian standards.
-
Page 3: Table Of Contents
WT40DC Plasma Cutter Contents Know Your Machine..........5 Controls Explained..........5 Tips & Tricks..............6 Quick Start Guide.............6 Basic Operation............7 Plasma Cutting Guide...........7 Accessories & Consumables......9 Knowledge & Resources........10 Care & Maintenance..........10 Safety..............10 Warranty...............15 www.weldtech.net.nz... -
Page 5: Know Your Machine
WT40DC Plasma Cutter Know Your Machine * Denotes more detailed explanation of function below. Rear Input Power Lead Power Switch Compressed Air Inlet Fitting Front Air Pressure Gauge Air Pressure Regulator Adjustment Knob* LCD Current Meter Error/ Overload Indicator* Cutting Current Adjustment Knob 2T/4T Trigger Mode Selector* 10. -
Page 6: Tips & Tricks
As with correct air pressure, clean, dry air is critical for formance, short life span, torch and machine dam- plasma cutting machine performance and reliability. age and void warranty. The WT40DC is designed with an internal air filtra- tion/ moisture separator to assist with providing suit- able air supply. The moisture separator is self-drain- Duty Cycle Rating... -
Page 7: Basic Operation
Adequate ventilation is required to provide proper cooling for the WT40DC. Ensure that the machine is placed on a stable level surface where clean cool air can easily flow through the unit. The WT40DC Effect of Cutting Speed has electrical components and control circuit boards... - Page 8 NOTE: The speeds given here are typical for best Operating Techniques quality cuts. Your actual speeds may vary depending Piercing - Materials (up to 3.2mm/1/8in. thick) on material composition, surface condition, operator may be pierced with the torch touching the technique, etc. work. When piercing thicker materials (up to 4.8mm stainless or carbon steel) at an angle, If cutting speed is too fast, you may lose the cut.
-
Page 9: Accessories & Consumables
15m H/D 15A Extension Lead (3 x 2.5mm wiring) & Consumables PDL15 3 Pin Plug, 15A 250V - Straight 16896 2m 15A H/D Molded Plug & Lead, Refer to page 4 for related accessories for this (3x2.5mm2 wiring) machine or visit www.weldtech.co.nz for a full range of consumables and accessories. WT-PT31 Torch Compatible Consumables WT45065 O-Ring WT18205 Electrode - Std. WT19683 Electrode - Long... -
Page 10: Knowledge & Resources
/ connections, make sure the welding machine is switched in Top Condition off and disconnected from the power supply. The WT40DC does not require any special mainte- nance, however the user should take care of the ma- Safety chine as follows: Store and Retain this Manual • Regularly clean the ventilation slots. - Page 11 WT40DC Plasma Cutter failure of the pacemaker. The use of a plasma NOTE, used to address practices not related to per- cutter is NOT RECOMMENDED for pacemaker sonal injury. wearers. Consult your doctor. General Safety Warnings 9. Ensure that the unit is placed on a stable lo- 1.
- Page 12 to equipment connected to power lines; other prac- 2. Do not overreach. Keep proper footing and bal- tices apply to engine driven equipment. ance at all times. This enables better control of the plasma cutter in unexpected situations. Anyone not having extensive training in welding and cutting practices should not attempt to use these machines.
- Page 13 WT40DC Plasma Cutter 3. Enclose the work area with portable fire resistant 6. After plasma cutting, make a thorough exami- screens. Protect combustible walls, ceilings, nation for evidence of fire. Be aware that visible floors, etc., from sparks and heat with fire re- smoke or flame may not be present for some sistant covers.
- Page 14 5. Work in a confined space only if it is well venti- Electricity Can Kill lated, or while wearing an air-supplied respirator. Be sure the breathing air is safe. DANGER! 6. Do not use plasma cutter in locations near de- Touching live electrical parts can cause fatal shocks greasing, cleaning, or spraying operations. The or severe burns.
-
Page 15: Warranty
To request a physical registration form, please contact Euroquip customer service on 0800 387 678. The decision that an issue with a product qualifies as a warranty claim is made at the sole jurisdiction of Registered warranty period for the WT40DC: Euroquip. Commercial Use: 18 Months Domestic Use: 18 Months... - Page 16 Congratulations on your new WELDTECH product. We are proud to have you as our customer and will strive to provide you with the best service and reliability in the industry. This product is backed by our extensive warranty and service network. To locate your nearest distributor or service agency visit www.weldtech.net.nz, or email us at info@euroquip.co.nz.
Need help?
Do you have a question about the WT40DC and is the answer not in the manual?
Questions and answers