Advertisement
Quick Links
ThinkSystem Heavy Duty Full Depth 42U Rack Cabinet
Unpacking Instructions
Unpack the rack cabinet
S037
Notes:
• Space requirement: You will need minimum of 2885 mm (113.6 inch) on the rear side of the pallet to
unpack the rack cabinet.
• Tool requirement: You will need one sharp tool.
• Forklift requirements:
Note: Only the front side of the pallet is available for the forklift.
Figure 1. Forklift
–
1
must be longer than 350 mm.
–
2
must be shorter than 700 mm.
CAUTION:
The weight of this part or unit is more than 200 kg (441 lb). It takes specially
trained persons, a lifting device, or both to safely lift this part or unit.
Make sure to follow fork-lift truck operating regulations to prevent overturning
of the rack cabinet.
1 1
Advertisement
Related Manuals for Lenovo ThinkSystem Heavy Duty
Summary of Contents for Lenovo ThinkSystem Heavy Duty
- Page 1 ThinkSystem Heavy Duty Full Depth 42U Rack Cabinet Unpacking Instructions Unpack the rack cabinet S037 CAUTION: The weight of this part or unit is more than 200 kg (441 lb). It takes specially trained persons, a lifting device, or both to safely lift this part or unit.
- Page 2 – must be between 1450 to 1650 mm. – Loading capacity must be larger than 3000 kg. Step 1. Cut the four straps with a sharp tool. Figure 2. Cutting the straps...
- Page 3 Step 2. Remove the top cover and side cardboards. Figure 3. Removing the cardboards Step 3. Remove the top bars and side boxes. Note: One of the side cartons contains the ramps and is quite heavy. Lifting it requires two people. Figure 4.
- Page 4 Step 4. Release and remove the side frames. Figure 5. Removing the side frames Slightly lift and slide the six horizontal bars left to disengage their right ends from the slots on the right frame. Remove the right frame along with the three horizontal bars. Remove the left frame along with the nine horizontal bars.
- Page 5 Step 5. Open the front door. Remove the twelve screws, the two bolts, and the front shipping bracket. Figure 6. Removing the front shipping bracket Step 6. Open the rear door. Remove the ten screws, the two bolts, and the rear shipping bracket. Figure 7.
- Page 6 Figure 8. Rising the leveling pads...
- Page 7 Step 8. Secure the ramp with one of the bolts that are removed from the shipping brackets. Figure 9. Securing the ramp Step 9. Place the ramp next to the cabinet front door, and slowly slide the rack cabinet down from the pallet to the designated location.
- Page 8 Figure 11. Removing the outrigger stabilizing bars Remove the eight screws that secure the two bars to the rack cabinet. Place the two stabilizing bars on the ground, and remove the bars. Step 11. Remove the four screws that secure each of the outriggers, and remove the outriggers. Figure 12.
- Page 9 Step 13. Secure the stabilizer to the floor with two screws. Figure 14. Securing the stabilizer to the floor...
- Page 10 Identify rack cabinet components Figure 15. Parts listing Table 1. Heavy Duty Full Depth 42U Rack Cabinet components Rack cabinet frame Keys (doors and side covers) Rear door Leveling pad Side covers Tools Outriggers (side stabilizers) Fixed caster 1 1 0 0...
- Page 11 Table 1. Heavy Duty Full Depth 42U Rack Cabinet components (continued) Front stabilizer Swivel caster Front door Baying kit Door latch Figure 16. Tool box 20 M6 C type caged nuts 30 M6 G type caged nuts 20 M5 C type caged nuts 10 M6 flanges 20 M5 screws 20 M6 screws...
- Page 12 First Edition (July 2021) © Copyright Lenovo 2021. Lenovo and the Lenovo logo are trademarks of Lenovo in the United States, other countries, or both. Other company, product, or service names may be trademarks or service marks of others. LIMITED AND RESTRICTED RIGHTS NOTICE: If data or software is delivered pursuant to a General Services Administration (GSA) contract, use, reproduction, or disclosure is subject to restrictions set forth in Contract No.