Device Ports; Modem (Rj-11) Telephone Jack; Internal Lan (Rj-45) Jack; Ieee 1394 Jack - Fujitsu LifeBook S-5582 User Manual

Fujitsu lifebook s5582: user guide
Hide thumbs Also See for LifeBook S-5582:
Table of Contents

Advertisement

Device Ports

Your Fujitsu LifeBook notebook and the optional Port
Replicator come equipped with multiple ports to which
you can connect external devices including: disk drives,
keyboards, modems, printers, etc.

MODEM (RJ-11) TELEPHONE JACK

The modem (RJ-11) telephone jack is used for an
internal modem. To connect the telephone cable follow
these easy steps: (See figure 2-7 on page 8 for location)
1. Align the connector with the port opening.
2. Push the connector into the port until it is seated.
3. Plug the other end of the telephone cable into a
telephone outlet.
The modem sound is deactivated by default, to activate
modem sound follow these easy steps:
1. Right click on the Speaker icon in your system tray.
2. Select Open Volume.
3. Select Option/Properties.
4. Under "Show the following volume controls", click
on Phone and click OK.
5. Uncheck the Mute box under Phone Balance.
W A R N I N G
The internal modem is not intended for use with Digital
PBX systems. Do not connect the internal modem to a
Digital PBX as it may cause serious damage to the inter-
nal modem or your entire LifeBook notebook. Consult
your PBX manufacturer's documentation for details.
Some hotels have Digital PBX systems. Be sure to find
out BEFORE you connect your modem.
P O I N T S
The internal modem is designed to the ITU-T V.90
standard. Its maximum speed of 53000bps is the
highest allowed by FCC, and its actual connection
rate depends on the line conditions. The maximum
speed is 33600bps at upload.
The internal modem on all Fujitsu LifeBook notebooks
from Fujitsu are certified for use in the United States
and Canada. The modem may be certified in other
countries.

INTERNAL LAN (RJ-45) JACK

The internal LAN (RJ-45) jack is used for an internal
Fast Ethernet (10/100 Base-T/Tx) connection. You may
need to configure your notebook to work with your
particular network. (Please refer to your network admin-
istrator for information on your network configuration.)
U s e r I n s t a l l a b l e F e a t u r e s
To connect the LAN cable follow these easy steps: (See
figure 2-8 on page 9 for location)
1. Align the connector with the port opening.
2. Push the connector into the port until it is seated.
3. Plug the other end of the cable into a LAN outlet.

IEEE 1394 JACK*

The 1394 port allows you to connect devices that are
compliant with IEEE standard 1394. This port is effec-
tively a very fast communications port. In order to
connect a 1394 device, follow these steps: (See figure 2-7
on page 8 for location)
1. Align the connector with the port opening.
2. Push the connector into the port until it is seated.
* Some digital devices - such as digital cameras - use
IEEE 1394 ports for fast transfer of digital files and
data.

PARALLEL PORT

The parallel port, or LPT port, located on the optional
Port Replicator allows you to connect parallel devices,
such as a printer to your notebook. In order to connect a
parallel interface device follow these easy steps: (See
figure 4-10 on page 47 for location)
1. Align the connector with the port opening.
2. Push the connector into the port until it is seated.
3. Tighten the two hold-down screws, located on
each end of the connector.

SERIAL PORT

The serial port, or COMM port, located on the optional
Port Replicator allows you to connect serial devices, such
as printers or scanners. In order to connect a serial inter-
face device follow these easy steps: (See figure 4-10 on
page 47 for location)
1. Align the connector with the port opening.
2. Push the connector into the port until it is seated.
3. Tighten the two hold-down screws, located on each
end of the connector.

PS/2 PORTS

The PS/2 ports located on the optional Port Replicator
allow
you to connect an external keyboard, and/or numeric
keypad and mouse. In order to connect a PS/2 interface
device follow these easy steps: (See figure 4-10 on page 47
for location)
1. Align the connector with the port opening.
2. Push the connector into the port until it is seated.
49

Hide quick links:

Advertisement

Table of Contents
loading

Table of Contents