Advertisement
5869
SPECIFICATIONS:
Physical:
• 1-15/16" W x 5-15/16" H x 1-3/16"D
(50mm x 150mm x 30mm)
Frequency:
• 345MHz
INSTALLATION:
Mount the 5869 under a counter or money drawer for easy access by the cashier. Refer to the
steps and figures that follow for typical mounting instructions.
Before mounting the 5869 permanently, perform Go/No Go tests to verify adequate transmitter
signal strength at desired mounting location (refer to the Security System Control Panel
Installation and Setup Guide).
1. Remove the two screws (Figure 1)
securing the cover to the 5869 case.
NOTE: The holes located in the opposite
corner, to the screws that secure the cover
to the case, provide a means for securing
the transmitter to the counter or drawer.
2. Using the case as a drill template, position
the case in the desired location.
3. Drill a 1/16-inch pilot hole at the breakaway
tamper release hole and the two case
mounting holes (Figure 2).
4. Attach the case to the counter or money
drawer using one No. 6 x 3/4 screw
(supplied) at the breakaway tamper
release.
5. Install the battery (see BATTERY
INSTALLATION/REPLACEMENT).
6. Secure the cover to the case with the two
screws removed in step 1.
7. Secure the assembled case to the counter
or drawer using the two No. 6 x 2
mounting screws supplied (Figure 2).
MOUNTING
COVER
HOLE
SCREW
TRIGGER
COVER
SCREW
MOUNTING
HOLE
HOLDUP
TRANSMITTER
DEVICE
L/5869TRAN/D 4/03
Programming
The 5869 Holdup Switch/Transmitter should
be programmed as a 24-hour silent zone
type. Refer to the Security System Control
Panel Installation and Setup Guide for
programming instructions.
NOTES:
• During programming of the control panel,
• The 5869 is one closed input loop zone
Battery Installation/Replacement
1. Remove and retain screws securing the
2. Observing correct polarity, insert the
3. Re-install screws to secure cover and/or
COVER
MOUNTING
ATTACH
HOLE
HOLE
SECURING
TABS FOR
CIRCUIT
BOARD
BREAKAWAY
TAMPER
RELEASE TAB
COVER
ATTACH
SCREW
HOLE
HOLE
MOUNTING
HOLE
COVER REMOVED
INSIDE VIEW
WITHOUT
CIRCUIT BOARD
5869-003-V0
FIGURE 1
Battery:
• 3-volt Lithium. ADEMCO 466
or equivalent.
Agency Listings:
• UL Listed for Household Burg UL1023
and Hold Up Burg UL636. Using 5881ENHC
with appropriate ADEMCO commercial listed panels
the 5869 Holdup Switch/Transmitter
should be treated as "RF" (i.e., supervised
RF) Type.
(loop 1).
5869 cover.
battery into the battery holder.
NOTE: Use care not to bend the antenna
while attempting to install battery.
assembly. Refer to Figure 1.
RESET
KEY
COVER
ATTACH
HOLE
MOUNTING
HOLE
TRIGGER
BREAKAWAY
TAMPER
RELEASE
CIRCUIT
SCREW HOLE
BOARD
TRIGGER
INDEX
BREAKAWAY
TAB
TAMPER
RELEASE
COVER
TAMPER
RELEASE
SWITCH
3V
+
MOUNTING
LITHIUM
HOLE
BATTERY
COVER
ATTACH HOLE
FIGURE 2
Holdup
Switch/
Transmitter
NOTE
CIRCUIT BOARD REMOVED
FOR CLARITY ONLY. DO NOT
REMOVE CIRCUIT BOARD
DURING INSTALLATION.
COVER
165 Eileen Way, Syosset, NY 11791
COVER
SCREW (2)
No. 6X1/2
Copyright ©2003 Honeywell International Inc.
+
MOUNTING
SCREW (2)
No. 6X2
ADEMCO is an ISO9001 Registered
Company
HOLE
+
COVER
SCREW
5869-002-V0
Advertisement
