Advertisement
MT20X0 Poster
MT20X0 Poster
BLACK
PANTONE 285
Optimum body posture
for low scanning
DRAFT
SYMBOL MT20X0
PERF
This device is approved under the Symbol Technologies brand: Symbol Technologies, Inc., is the
Enterprise Mobility business of Motorola, Inc. ("Motorola").
All Motorola/Symbol devices are designed to be compliant with rules and regulations in locations they
are sold and will be labeled as required.
Local langauge translations are available at the following website: http://support.symbol.com
Any changes or modifications to Motorola/Symbol Technologies equipment, not expressly approved
by Motorola/Symbol Technologies, could void the user's authority to operate the equipment.
CAUTION:
Only use Motorola/Symbol approved and UL Listed accessories, battery packs and battery chargers.
Do NOT attempt to charge damp/wet mobile computers or batteries. All components must be dry
before connecting to an external power source.
Wireless Device Country Approvals
Regulatory markings, subject to certification, are applied to the device signifying the radio(s) is/are approved for use
in the following countries: United States, Canada, Japan, China, S. Korea, Australia, and Europe 1
Please refer to the Symbol Declaration of Conformity (DoC) for details of other country markings.
This is available at http://www2.symbol.com/doc/.
Note 1: For 2.4GHz or 5GHz Products: Europe includes, Austria, Belgium, Bulgaria, Czech Republic, Cyprus, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Liechtenstein, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Slovak Republic, Slovenia, Spain, Sweden, Switzerland and the United Kingdom.
Operation of the device without regulatory approval is illegal.
Frequency of Operation – FCC and IC
5 GHz Only
The use in the UNII (Unlicensed National Information Infrastructure) band 1 5150-5250 MHz band is
restricted to Indoor Use Only; any other use will make the operation of this device illegal.
2.4 GHz Only
The available channels for 802.11 b/g operation in the US are Channels 1 to 11. The range of channels is limited by firmware.
Health and Safety Recommendations
Ergonomic Recommendations
Caution: In order to avoid or minimize the potential risk of ergonomic injury follow the recommendations below. Consult with your
local Health & Safety Manager to ensure that you are adhering to your company's safety programs to prevent employee injury.
• Reduce or eliminate repetitive motion
• Perform tasks at correct heights
• Maintain a natural position
• Reduce or eliminate vibration
• Reduce or eliminate excessive force
• Reduce or eliminate direct pressure
• Keep objects that are used
• Provide adjustable workstations
frequently within easy reach
Warnings for Use of Wireless Devices
Please observe all warning notices with regard to the usage of wireless devices
Safety in Hospitals
Wireless devices transmit radio frequency energy and may affect medical electrical equipement.
Wireless devices should be switched off wherever you are requested to do so in hospitals, clinics or healthcare
facilitlies. These requests are designed to prevent possible interference with sensitive medical equipement.
Pacemakers
Pacemaker manufacturers recommended that a minimum of 15cm (6 inches) be maintained between a handheld
wireless device and a pacemaker to avoid potential interference with the pacemaker. These recommendations
are consistent with independent research and recommendations by Wireless Technology Research.
Persons with Pacemakers:
• Should ALWAYS keep the device more than 15cm (6 inches) from their pacemaker when turned ON.
• Should not carry the device in a breast pocket.
• Should use the ear furthest from the pacemaker to minimise the potential for inter¬ference.
• If you have any reason to suspect that interference is taking place, turn OFF your device.
Other Medical Devices
Please consult your physician or the manufacturer of the medical device, to determine if the operation of your
wireless product may interfere with the medical device.
RF Exposure Guidelines
Safety Information
Reducing RF Exposure – Use Properly
Only operate the device in accordance with the instructions supplied.
International
The device complies with internationally recognized standards covering human exposure to electromagnetic
fields from radio devices.
EU
Handheld Devices
To comply with EU RF exposure requirements, this device must be operated in the hand with a minimum
separation distance of xxcm or more from a person' s body. Other operating configurations should be avoided.
For information on "International" human exposure to eletromagnic fields refer to the Motorola/Symbol
Declaration of Conformity (DoC) at http://www2.symbol.com/doc/.
US and Canada
Handheld Devices
To comply with FCC RF exposure requirements, this device must be operated in the hand with a minimum
separation distance of 20 cm or more from a person's body. Other operating configurations should be avoided.
Motorola, Inc. One Motorola Plaza Holtsville, New York 11742, USA
1-800-927-9626 http://www.symbol.com
72-117308-01 Revision A January 2009
SYMBOL MT20X0
OPTIMUM UPRIGHT BODY POSTURE
Avoid Extreme Wrist Angles
AVOID EXTREME
WRIST ANGLES
OPTIMUM BODY POSTURE
Alternate left
and right knees
AVOID BENDING
AVOID REACHING
REGULATORY INFORMATION
Batteries
Charging –
To charge the mobile device battery, the battery and charger temperatures must be between + 32 º F and + 104 º F (0 º C and + 40 º C).
Please follow the local regulations when disposing of re-chargeable batteries.
Taiwan - Recycling
EPA (Environmental Protection Administration) requires dry battery producing or importing firms in accordance
with Article 15 of the Waste Disposal Act are required to indicate the recycling marks on the batteries used in
sales, giveaway or promotion. Contact a qualified Taiwanese recycler for proper battery disposal.
However, there are limitations to how long a battery can operate or be stored before needing replacement. Many factors
affect the actual life cycle of a battery pack, such as heat, cold, harsh environmental conditions and severe drops.
When batteries are stored over six (6) months, some irreversible deterioration in overall battery quality may occur.
Store batteries at half of full charge in a dry, cool place, removed from the equipment to prevent loss of capacity, rusting
of metallic parts and electrolyte leakage. When storing batteries for one year or longer, the charge level should be
verified at least once a year and charged to half of full charge.
Replace the battery when a significant loss of run time is detected.
Standard warranty period for all Symbol batteries is 30 days, regardless if the battery was purchased separately
|or included as part of the mobile computer or bar code scanner. For more information on Symbol batteries,
please visit: http:/mysymbolcare.symbol.com/battery/batbasics1.htm
Battery Safety Guidelines
• The area in which the units are charged should be clear of debris and combustible materials or chemicals.
Particular care should be taken where the device is charged in a non commercial environment.
• Follow battery usage, storage, and charging guidelines found in the user's guide.
• Improper battery use may result in a fire, explosion, or other hazard.
• To charge the mobile device battery, the battery and charger temperatures must be
between +32 ºF and +104 ºF (0 ºC and +40 ºC)
• Do not use incompatible batteries and chargers. Use of an incompatible battery or charger may present a risk
of fire, explosion, leakage, or other hazard. If you have any questions about the compatibility of a battery or
a charger, contact Motorola Enterprise Mobility support.
• For devices that utilize a USB port as a charging source, the device shall only be connected to products that
bear the USB-IF logo or have completed the USB-IF compliance program.
• Do not disassemble or open, crush, bend or deform, puncture, or shred.
• Provide adequate clearance
• Severe impact from dropping any battery-operated device on a hard surface could cause the battery to overheat.
• Provide a suitable working
• Do not short circuit a battery or allow metallic or conductive objects to contact the battery terminals.
environment
• Do not modify or remanufacture, attempt to insert foreign objects into the battery, immerse or expose to water
• Improve work procedures.
or other liquids, or expose to fire, explosion, or other hazard.
• Do not leave or store the equipment in or near areas that might get very hot, such as in a parked vehicle or
near a radiator or other heat source. Do not place battery into a microwave oven or dryer.
• Battery usage by children should be supervised.
• Please follow local regulations to promptly dispose of used re-chargeable batteries.
• Do not dispose of batteries in fire.
• Seek medical advice immediately if a battery has been swallowed.
• In the event of a battery leak, do not allow the liquid to come in contact with the skin or eyes. If contact has
been made, wash the affected area with large amounts of water and seek medical advice.
• If you suspect damage to your equipment or battery, contact Motorola Enterprise Mobility support to arrange
for inspection.
1. Radio Frequency Interference Requirements- FCC
Note: This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio
FOR HOME OR OFFICE USE
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help.
Radio Transmitters (Part 15)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
2. Radio Frequency Interference Requirements- Canada
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Radio Transmitters
For RLAN Devices:
The use of 5 GHz RLAN's, for use in Canada, have the following restrictions:
• Restricted Band 5.60 – 5.65 GHz
This device complies with RSS 210 of Industry & Science Canada. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Label Marking: The Term "IC:" before the radio certification only signifies that Industry Canada technical
specifications were met.
3. Marking and European Economic Area (EEA)
The use of 2.4GHz RLAN's, for use through the EEA, have the following restrictions:
• Maximum radiated transmit power of 100 mW EIRP in the frequency range 2.400 -2.4835 GHz.
• France, outside usage is restricted to 2.4 – 2.454 GHz.
• Italy requires a user license for outside usage.
The use of 5GHz RLAN's has varying restrictions for use within the EEA; please refer to the Motorola/Symbol
Declaration of Conformity (DoC) for details at http://www2.symbol.com/doc/.
Bluetooth® Wireless Technology for use through the EEA has the following restrictions:
• Maximum radiated transmit power of 100mW EIRP in the frequency range 2.400 -2.4835 GHz
• France, outside usage is restricted to 10mW EIRP
• Italy requires a user license for outside usage.
MOTOROLA and the Stylized M Logo and Symbol and the Symbol logo are registered in the U.S. Patent and Trademark Office.
All other product or service names are the property of their respective owners. © Motorola, Inc. 2009
http://www.motorola.com/mt20x0
CRADLE CONVERSION
Beeper Indications
Standard Use
Low-medium-high beeps
Normal beep
Power up
Bar code decoded [if
decode beeper enabled]
Short low-high beeps
Short high-low beeps
Scanner has paired with
Scanner has unpaired
the cradle
with the cradle
Parameter Menu Scanning
High-low-high-low beeps
Long low-high beeps
Successful program exit with change
Input error, incorrect programming
in the parameter setting
sequence,or Cancel bar code scanned
LED Indications
Standard Use
Off
Green
No power applied to scanner (battery
Bar code successfully
discharged or removed), or scanner
decoded
is in low power and ready to scan
Charging Use
Green Slow Flash
Green Fast Flash
Scanner charging at
Scanner charging at a
a slow rate (used
fastrate (used when
when cradle is
cradleis powered from
powered by host cable)
external power supply)
Optimum body posture for
extended range scanning
Recommended Usage Guide
Statement of Compliance
Motorola/Symbol hereby, declares that this device is in compliance with the essential requirements and other relevant
provisions of Directive 1999/5/EC. A Declaration of Conformity may be obtained from http://www2.symbol.com/doc/.
Japan (VCCI) - Voluntary Control Council for Interference
この装置は、 情報処理装置等電波障害自主規制協議会 （ＶＣＣＩ） の基準に基づく クラスB情報技術装置です。 この
装置は、 家庭環境で使用することを目的としていますが、 この装置がラジオやテレビジョン受信機に近接して使用さ
れると、 受信障害を引き起こすことがあります。 取扱説明書に従って正しい取り扱いをして下さい。
This is a Class B product based on the standard of the Voluntary Control Council for Interference from Information
Technology Equipment (VCCI). If this is used near a radio or television receiver in a domestic environment, it may
cause radio interference. Install and use the equipment according to the instruction manua
Other Countries
Brazil
Declarações Regulamentares para MT2090 - Brasil
Nota: "A marca de certificação se aplica ao Transceptor, modelo MT2090. Este equipamento opera em caráter
secundário, isto é, não tem direito a proteção contra interferência prejudicial, mesmo de estações do mesmo tipo,
e não pode causar interferência a sistemas operando em caráter primário."
Para maiores informações sobre ANATEL consulte o site: www.anatel.gov.br
Mexico -
Restrict Frequency Range to: 2.450 – 2.4835 GHz.
l
Sri Lanka -
Restrict Frequency Range to: 2.400 – 2.430 GHz.
Taiwan -
臺灣
低功率電波輻射性電機管理辦法
第十二條
經型式認證合格之低功率射頻電機， 非經許可， 公司、 商號或使用者均不得擅自變更頻率、
加大功率或變更原設計之特性及功能。
第十四條
低功率射頻電機之使用不得影響飛航安全及干擾合法通信 ； 經發現有干擾現象時， 應立即停用，
並改善至無干擾時方得繼續使用。
前項合法通信， 指依電信規定作業之無線電通信。
低功率射頻電機須忍受合法通信或工業、 科學及醫療用電波輻射性電機設備之干擾。
限制頻率範圍是 ：
最大發射功率: 27dBm
2.400 - 2.4835 GHz。
5.250 - 5.350 GHz。
最大發射功率: 17dBm
最大發射功率: 24dBm
5.725 - 5.850 GHz。
2.4GHz ： 11個通道
5GHz ： 8個通道
在5.25-5.35
赫頻帶內操作之無線資訊傳輸設備， 限於室內使用。
Laser Labels
In accordance with Clause 5. IEC 825 and EN60825, the following information is provided to the user
Laser Devices
Complies with 21CFR1040.10 and 1040.11 except for deviations pursuant to Laser Notice No. 50, dated July 26, 2001.
EN60825-1:1994+ A1:2002 +A2:2001
IEC60825-1:1993+A1:1997+A2:2001
The laser classification is marked on one of the labels on the device.
Class 1 Laser devices are not considered to be hazardous when used for their intended purpose. The following statement
is required to comply with US and international regulations:
Caution: Use of controls, adjustments or performance of procedures other than those specified herein may result in
hazardous laser light exposure.
Class 2 laser scanners use a low power, visible light diode. As with any very bright light source, such as the sun, the user
should avoid staring directly into the light beam. Momentary exposure to a Class 2 laser is not known to be harmful.
LASER LIGHT
DO NOT STARE INTO BEAM
CLASS 2 LASER PRODUCT
LASERSTRAHLUNG
NIGHT IN DEN STRAHL
BLICKENLASER KLASSE 2
LUMIERE LASER
NE PAS REGARDER DANS LE
FA I SC EAUAPP
AREIL A LASER DE CLASSE 2
CLASS 1 LASER PRODUCT
LASER KLASSE 1
APPAREIL A LASER DE CLASSE 1
4 long low beeps
4 short high beeps
Transmission error
Low battery
detected; data is ignored
indication
Long low-high beeps or
Long low-high-low-high beeps
Unsuccessful pairing attempt
Red
Data transmission
error or scanner malfunction
or Symbol LS3578 scanner
inserted into an STB3478
cradle
Red Flash
Red and Green Flash
Charging problem
Temperature fault
See Product Reference
Guide for more
information
PERF
Advertisement
