Worksaver ULF-246 Owner's/Operator's Manual

Universal loader fork and skid steer pallet fork

Hide thumbs

page of 20

/ 20
Bookmarks

Quick Links

Download this manual

OWNER'S /

OPERATOR'S

MANUAL

MODEL NO.'s

ULF-246

SSPF-20

CAUTION

For Safe Operation

Read Rules And

Instructions Carefully

SINO LEEINGLES, PIDA AYUDA

A AIGUIEN QUE SI LO LEA

PARA QUE LE TRADUZCA LAS

MEDIDAS DE SEGURIDAD.

THE FOLLOWING SAFETY PRECAUTIONS SHOULD BE THOROUGHLY UNDERSTOOD

BEFORE ATTEMPTING TO BEGIN ASSEMBLING THIS MACHINE

1. Select an area for assembly that is clean and free of any

debris which might cause persons working on the

assembly to trip.

2. Do not lift heavy parts or assemblies. Use crane, jack,

tackle, fork trucks or other mechanical devices.

3. Preview the assembly instructions in your operator's

manual before proceeding further.

4. If the assembly instructions call for parts or assemblies to

be blocked up, use only blocking material that is in good

condition and is capable of handling the weight of the

assembly to be blocked. Also insure that the blocking

material is on a clean, dry surface.

5. Never put hands, or any part of body, under blocked up

assemblies if at all possible.

UNIVERSAL LOADER FORK

SKID STEER PALLET FORK

Safety Instructions

Tractor Preparation

Operating Instructions

C A U T I O N

6. After completing assembly, thoroughly inspect the

machine to be sure that all nuts, bolts, hydraulic fittings

or any other fastened assemblies have been thoroughly

tightened.

7. Before operating the machine, thoroughly read the

operation section of your operator's manual.

8. Before operating, read the maintenance section of your

operator's manual to be sure that any parts requiring

lubrication, such as gearboxes, are full, to avoid any

possible damage.

9. Before operating equipment – If you have any

questions regarding the proper assembly or

operation, contact your dealer or representative.

and

Assembly & Mounting

Maintenance

Repair Parts

Need help?

Do you have a question about the ULF-246 and is the answer not in the manual?

Questions and answers

Summary of Contents for Worksaver ULF-246

Page 1 OWNER’S / OPERATOR’S MANUAL MODEL NO.’s ULF-246 SSPF-20 UNIVERSAL LOADER FORK CAUTION For Safe Operation Read Rules And SKID STEER PALLET FORK Instructions Carefully SINO LEEINGLES, PIDA AYUDA Safety Instructions Assembly & Mounting A AIGUIEN QUE SI LO LEA PARA QUE LE TRADUZCA LAS...
Page 2 Like all mechanical products, it will require cleaning and upkeep. Use only genuine Worksaver, Inc. service parts. Substitute parts will void the warranty and may not meet stan- dards required for safe and satisfactory operation. Record the model and serial number of your Loader Fork here: Model:________________________________________ Serial Number:_______________________________ RETAIL CUSTOMER’S RESPONSIBILITY...
Page 3 2. If the unit has been subjected to misapplication, abuse, misuse, negligence, fire or other accident. 3. If parts not made or supplied by Worksaver have been used in connection with the unit, if, in sole judge- ment of Worksaver such use affects its performance, stability, or reliability.
Page 4 To the Owner/Operator/Dealer All implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-minded opera- tor who recognizes the potential hazards and follows reasonable safety practices. The manufacturer has designed this implement to be used with all its safety equipment properly attached to minimize the chance of accidents. BEFORE YOU START!! Read the safety messages on the implement and shown in your manual.
Page 5 SAFETY INSTRUCTIONS ( continued) EQUIPMENT SAFETY GUIDELINES Safety of the operator is one of the main concerns in designing and developing a new piece of equipment. Designers and manufacturers build in as many safety features as possible. However, every year many accidents occur which could have been avoided by a few seconds of thought and a more careful approach to handling equipment.
Page 6 SAFETY INSTRUCTIONS ( continued) SAFETY TRAINING Safety is a primary concern in the design and manufacture of our products. Unfortunately, our efforts to provide safe equipment can be wiped out by a single careless act of an operator. In addition to the design and configuration of equipment, hazard control and accident prevention are dependent upon the awareness, concern, prudence and proper training of personnel involved in the operation, transport, maintenance and storage of equipment.
Page 7 SAFETY INSTRUCTIONS ( continued) SAFETY SIGNS Keep safety signs clean and legible at all times. Replace safety signs that are missing or have become illegible. Replaced parts that displayed a safety sign should also display the current sign. Safety signs are available from your Distributor or Dealer Parts Department or the factory. How to Install Safety Signs: Be sure that the installation area is clean and dry.
Page 8 SAFETY INSTRUCTIONS ( continued) OPERATIONAL SAFETY The use of this equipment is subject to certain hazards which cannot be protected against by mechanical means or product design. All operators of this equipment must read and understand this entire manual, paying particular attention to safety and operating instructions, prior to using.
Page 9 SAFETY INSTRUCTIONS ( continued) OPERATIONAL SAFETY (continued) Before you operate any equipment, check over all pins, bolts and connections to be sure all are securely in place. Replace any damaged or worn parts immediately. Do not work under a raised loader unless it is securely blocked or held in position. Do not depend on the power unit hydraulic system to hold the implement in place.
Page 10 SAFETY INSTRUCTIONS ( continued) OPERATIONAL SAFETY (continued) When maneuvering close to buildings or passing through narrow areas, be sure to allow sufficient clearance for the power unit, loader, and load. Drive slowly. Operate loader from operator’s seat only. Remain at controls until operating cycle is complete. Use extreme care when working on inclines and hillsides.
Page 11 SAFETY INSTRUCTIONS ( continued) TRANSPORT SAFETY Comply with state and local laws governing highway safety and movement of farm machinery on public roads. The use of flashing amber lights is acceptable in most localities. However, some localities prohibit their use. Local laws should be checked for all highway lighting and marking requirements.
Page 12 SAFETY INSTRUCTIONS ( continued) MAINTENANCE SAFETY Good maintenance is your responsibility. Poor maintenance is an invitation to trouble. Follow good shop practices. - Keep service area clean and dry. - Be sure electrical outlets and tools are properly grounded. - Use adequate light for the job at hand. Make sure there is plenty of ventilation.
Page 13 SAFETY INSTRUCTIONS ( continued) MAINTENANCE SAFETY (continued) After servicing, be sure all tools, parts and service equipment are removed. Check to ensure all safety signs are installed and in good condition. (See safety sign section for location drawing.) Do not allow grease or oil to build up on any deck or platform. Never replace hex bolts with less than grade five bolts unless otherwise specified, i.e.
Page 14 SAFETY SIGNS REPLACE SAFETY DECALS DAMAGED MISSING!
Page 15 Keep load low. I N S T R U C T I O N S The Worksaver Universal Loader Fork is designed to fit W A R N I N G ! most medium size double-cylinder front end loaders with a load arm center distance of 42 inches or less.
Page 16 1 ” diameter pins from the lock collars on each side of each fork tine. Worksaver (part #830318). Be sure to indicate if two (2) or four (4) pins are required. ADJUSTING TINE WIDTH 1. Block up the forklift frame.
Page 17 INSTRUCTIONS ( continued) • Do not use the loader for a work platform. O P E R ATE SAFELY • Do not lift or carry anyone on loader or in bucket or attachment. • Carry load low. C A U T I O N ! •...
Page 18 ULF-246 & SSPF-20 PA RT S D R AW I N G...
Page 19 ULF-246 & SSPF-20 PA RTS LIST...
Page 20 INFORMATION: HOLIDAY FROM ACCIDENTS! 1. PART NUMBER 2. PART DESCRIPTION 3. MODEL NUMBER 4. NAME OF ITEM DECEMBER 2001 W O R K S AVER, INC. P.O. BOX 100 LITCHFIELD, IL 62056-0100 (217) 324-5973 WEB: http:// www.worksaver.com E-MAIL: sales@worksaver.com WS-TA001-OG...

This manual is also suitable for:

Sspf-20