Quoizel WKF8407EK Assembly Instruction Sheet

Please go to www.quoizel.com
Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.
Light Source: (1) A19 Medium Base bulb 100W Maximum or
(1) Medium Base Vintage bulb is recommended but not supplied.
Estimated Assembly Time:
Preparation: Identify and inspect all parts before beginning installation. Check package content list and diagrams below to ensure all parts are
present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture. Contact customer service for replacement
parts.
Fixture can only be mounted in the direction indicated on page 2.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
Package Contents
Crossbar Assembly
A
x 1
Alternate
B Mounting screw
x 2
-
STEP 1 Install Bulb and Cage
A. Remove lock screws from the Fixture Body (C).
B. Insert the bulb onto the socket and screw snugly into place.
C. Align the label "A" on the top edge of the Cage (D) to the label "A" in
the bottom edge of the fixture hood. Attach the Cage (D) to the fixture
hood and secure with previously removed lock screws. Hand tighten
until snug with screwdrivers.
Socket
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184
2017 QuoizelInc.
Assembly Instruction Sheet #IS-WKF8407EK
for product cleaning tips. Go to the
20-30 minutes
Fixture Body
C
x 1
Cage with
D Glass Panels
x 1
C
Label "A"
Vintage Bulb
(recommended
but not supplied)
Label "A"
Lock Screw
D
Figure 1
Thank you for purchasing a Quoizel product.
or visit us on-line at www.quoizel.com
For Style WKF8407EK
Care + Maintenance selection.
-
STEP 2 Installing the Crossbar Assembly
A. Pass the supply wires through the Crossbar Assembly (A). Attach
the Crossbar Assembly (A) to the Outlet Box with the head of the
Green Ground Screw facing you. Secure the Crossbar Assembly (A)
with Outlet Box Screws (not included). Tighten until snug
Note: Use the Alternate Shorter Mounting Screw (B) if your
installation requires a shorter mounting screw.
Outlet
Box
Mounting Screw
or Alternate Short
Mounting Screw
-
STEP 3 Test Fit the Backplate to the Crossbar Assembly
A. Remove the mounting balls from the Crossbar Assembly (A). Place
the backplate and Fixture Body (C) onto the Crossbar Assembly (A)
and secure with mounting balls. Note: The backplate and Fixture
Body (C) should be snug against the wall and held tight with the
mounting balls. If it is not, adjust the length of the mounting screw or
alternate short mounting screw on the Crossbar Assembly (A) by
unscrewing the preassembled hex nut and lock washer and then
screwing the mounting screws or alternate short mounting screws in
or out of the crossbar until the correct length is achieved. Once the
backplate and Fixture Body (C) is secure, remove the mounting ball
and Fixture Body (C) and proceed to Step 4.
Mounting Screw
or Alternate Short
Mounting Screw
Hex Nut and
Lock Washer
1of2
Outlet Box Screws
(not included)
A
Supply Wires
with Ground Wire
Figure 2
Backplate
Mounting Ball
C
A
ReleasedDate:2017-09-29
.
Figure 3