Quoizel LLE8411WT Assembly Instruction Sheet

6 CORPORATE PARKWAY
, .
GOOSE CREEK SC 29445
. .
www quoizel com
Please go to www.quoizel.com
Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.
Light Source: (1) A21 Medium Base Bulb 150W Maximum or
(1) Medium Base Vintage Bulb is recommended but not supplied.
Estimated Assembly Time:
Preparation: Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are
present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture. Contact customer service for replacement
parts.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
Package Contents
Crossbar Assembly
A
x 1
Alternate
B Mounting screw
x 2
-
STEP 1 Install Crossbar Assembly
A. Pass the supply wires through the Crossbar Assembly (A). Attach
the Crossbar Assembly (A) to the Outlet Box with the head of the
Green Ground Screw facing you. Secure it with Outlet Box Screws
(not included). Tighten until snug
Note: Use the Alternate Shorter Mounting Screw (B) if your
installation requires a shorter mounting screw.
Outlet Box
Mounting Screw
or Alternate Short
Mounting Screw
STEP 2 - Test Fit the Backplate to the Crossbar Assembly
A. Remove the mounting balls from the Crossbar Assembly (A). Place
the backplate and Fixture Body (C) onto the Crossbar Assembly (A)
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184
2017 QuoizelInc.
Assembly Instruction Sheet #IS-LLE8411WT
for product cleaning tips. Go to the
30-45 minutes
Fixture Body
C
x 1
D
E
Glass
F Shade
x 1
.
Supply Wires with
Ground Wire
A
Outlet Box Screws
(not included)
Figure 1
Thank you for purchasing a Quoizel product.
or visit us on-line at www.quoizel.com
For Style LLE8411WT
Care + Maintenance selection.
(Step 2 Continued)
and secure with mounting balls. Note: The backplate and Fixture
Body (C) should be snug against the wall and held tight with the
mounting balls. If it is not, adjust the length of the mounting screws
or alternate short mounting screws on the Crossbar Assembly (A) by
unscrewing the preassembled hex nut and lock washer and then
screwing the mounting screws or alternate short mounting screws in
or out of the crossbar until the correct length is achieved. Once the
backplate and Fixture Body (C) is secure, remove the mounting ball
Glass Holder
and Fixture Body (C) and proceed to Step 3.
x 1
Lock Ball
x 2
STEP 3 - Wire Connections
A. Wrap bare or green ground wire around green ground screw on the
crossbar, no less than 2 inches from the end of the wire. Tighten the
green ground screw.
B. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
from outlet box
Black wire from
outlet box (or Red)
Bare, or Green
from outlet box
1of2
Mounting Screw
or Alternate Short
Mounting Screw
Mounting Ball
A
Backplate
Hex Nut and
Lock Washer
White wire
Ground wire
Green Ground Screw
on the Crossbar
Figure 2
C
White wire
from fixture
Black wire
from fixture
Ground wire
from Fixture
Figure 3
ReleasedDate:2017-09-14