Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for PHI VILLA AH-FP-30F
Summary of Contents for PHI VILLA AH-FP-30F
- Page 1 ELECTRIC HEATER INSTRUCTION MANUAL AH-FP-30F , AH-FP-36F AH-FP-40F , AH-FP-48F ATTENTION: 1.Find a location for the electric heater that is protected from direct sunlight. 2.Do not plug the electric heater into the power outlet before you read all instructions.
-
Page 2: Important Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS FOR FUTURE USE WHEN USING ELECTRICAL APPLIANCES, BASIC PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND INJURY TO PERSONS, INCLUDING THE FOLLOWING: Read all instructions before using this heater. Failure to follow these important safety instructions may cause fire, electric shock or damage. -
Page 3: Electrical Parameter
used as a drying rack for clothing. Do not hand any decorations on the heater. 14)Do not modify this heater. Use this heater only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons. -
Page 4: Parts List
Parts list REF NO DESCRIPTION 8 PCS #8 x 1” 8 PCS 1 PC 4 PCS 2 PCS Installation: Caution: This heater can be installed in two ways, which can be selected according to your preference. Type 1. Built-in Wall Clearance: Please allow a minimum of 0.5”... - Page 5 Unit Overall Dimensions Model Cutout Dimensions(W*D*H) AH-FP-30F 30” x 6.2” x17.7” 26.75”x 6.313”x 17.125” AH-FP-36F 36” x 6.2” x17.7” 32.75”x 6.313”x 17.125” AH-FP-40F 40” x 6.2” x17.7” 36.75”x 6.313”x 17.125” AH-FP-48F 48” x 6.2” x17.7” 44.75”x 6.313”x 17.125” Step 1: (1)Find the two mounting screws and remove them. (2)Remove the front cover by pulling it upward (See Fig.
- Page 6 Fig. C Type 2. Wall Hanging Step 1: Select the wall location where you want to hang your electric heater. Draw a horizontal line using a level and mark 4 drill holes for the 4 anchor screws. Note: The holes are for mounting of heater and it shall be level so that the heater can be mounted properly and leveled.
- Page 7 Step 4: (1)Find the two mounting screws and remove them. (2)Remove the front cover by pulling it upward (See Fig. D(1)and Fig.D(2)). Fig.D(1) Fig. D(2) Step 5: Mount the heater on wall using the keyhole slots of the metal bracket at the back of the heater.
-
Page 8: Operation
Step 6: Secure the mounting bracket to the heater using 2 mounting screws. See Fig. Fig. F Step 7：Replace the front cover and secure it with two mounting screws (See Fig. G). Fig. G OPERATION After reading all the instructions, make sure that all the fireplace controls are in the OFF position. - Page 9 Operation with The Control Panel The controls are located at the front lower side of your heater. : Press this button to turn ON the fireplace. The unit will beep. Press again to turn off the fireplace and the fan will continue to work for 60 seconds without heat.
- Page 10 sequence of orange, orange and blue, blue. : Press up or down button to the desired temperature. When desired ambient temperature is reached, the heater will automatically stop heating. When the ambient temperature drops below the desired temperature 2°C, the heater will resume heating.
Need help?
Do you have a question about the AH-FP-30F and is the answer not in the manual?
Questions and answers