Land Pride FDR1648 Operator's Manual page 6

Rear discharge grooming mowers
Hide thumbs Also See for FDR1648:
Table of Contents

Advertisement

Important Safety Information
Listed below are common practices that may or may not be applicable to the products
described in this manual.
Use A Safety Chain
 A safety chain will help control
drawn machinery should it
separate from the tractor drawbar.
 Use a chain with the strength
rating equal to or greater than the
gross weight of the towed
implement.
 Attach the chain to the tractor
drawbar support or other specified
anchor location. Allow only
enough slack in the chain to
permit turning.
 Always hitch the implement to the
machine towing it. Do not use the
safety chain to tow the implement.
Tire Safety
 Tire changing
can be
dangerous
and must be
performed by
trained personnel
using the correct tools and
equipment.
 Always properly match the wheel
size to the properly sized tire.
 Always maintain correct tire
pressure. Do not inflate tires
above recommended pressures
shown in the Operator's Manual.
 When inflating tires, use a clip-on
chuck and extension hose long
enough to allow you to stand to
one side and NOT in front of or
over the tire assembly. Use a
safety cage if available.
 Securely support the implement
when changing a wheel.
 When removing and installing
wheels, use wheel handling
equipment adequate for the
weight involved.
 Make sure wheel bolts have been
tightened to the specified torque.
2
Transport Safely
 Comply with federal, state, and
local laws.
 Use towing vehicle and trailer of
adequate size and capacity. Secure
equipment towed on a trailer with
tie downs and chains.
 Sudden braking can cause a towed
trailer to swerve unexpectedly.
Reduce speed if towed trailer is not
equipped with brakes.
 Avoid contact with any overhead
utility lines or electrically charged
conductors.
 Always drive with load on end of
loader arms low to the ground.
 Always drive straight up and down
steep inclines with heavy end of
skid steer on the "uphill" side.
 Engage park brake when stopped
on an incline.
Practice Safe Maintenance
 Understand procedure before doing
work. Refer to the Operator's
Manual for additional information.
 Work on a level surface in a clean
dry area that is well-lit.
 Lower implement to the ground and
follow all shutdown procedures
before leaving the operator's seat to
perform maintenance.
 Do not work under any hydraulically
supported equipment. It can settle,
suddenly leak down, or be lowered
accidentally. If it is necessary to
work under the equipment,
securely support it with stands or
suitable blocking beforehand.
 Use properly grounded electrical
outlets and tools.
 Use correct tools and equipment for
the job that are in good condition.
 Allow equipment to cool before
working on it.
 Maximum transport speed for an
attached equipment is 20 mph
(32 km/h). DO NOT EXCEED.
Never travel at a speed which does
not allow adequate control of
steering and stopping. Some rough
terrains require a slower speed.
 As a guideline, use the following
maximum speed weight ratios for
attached equipment:
20 mph (32 km/h) when weight
of attached equipment is less
than or equal to the weight of
machine towing the equipment.
10 mph (16 km/h) when weight of
attached equipment exceeds
weight of machine towing
equipment but not more than
double the weight.
 IMPORTANT: Do not tow a load
that is more than double the weight
of the vehicle towing the load.
 Disconnect battery ground cable (-)
before servicing or adjusting
electrical systems or before welding
on implement.
 Inspect all parts. Make certain
parts are in good condition &
installed properly.
 Replace parts on this implement
with genuine Land Pride parts only.
Do not alter this implement in a way
which will adversely affect its
performance.
 Do not grease or oil implement
while it is in operation.
 Remove buildup of grease, oil, or
debris.
 Always make sure any material and
waste products from the repair and
maintenance of the implement are
properly collected and disposed.
 Remove all tools and unused parts
from equipment before operation.
 Do not weld or torch on galvanized
metal as it will release toxic fumes.
12/2/21

Hide quick links:

Advertisement

Table of Contents
loading

Table of Contents