Page 1
HP Pavilion tx2500 Entertainment PC Maintenance and Service Guide...
Page 2
The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty.
Page 3
Safety warning notice WARNING! To reduce the possibility of heat-related injuries or of overheating the computer, do not place the computer directly on your lap or obstruct the computer air vents. Use the computer only on a hard, flat surface. Do not allow another hard surface, such as an adjoining optional printer, or a soft surface, such as pillows or rugs or clothing, to block airflow.
Page 6
Workstation guidelines ..............34 Equipment guidelines ............... 35 Unknown user password ....................36 Component replacement procedures ....................37 Service tag location ......................37 Computer feet ........................38 Battery ..........................39 Pen ............................ 40 Hard drive .......................... 41 Optical drive ........................43 Memory module .........................
Page 7
12.1-inch, WXGA BrightView display specifications ................78 Hard drive specifications ........................79 DVD±RW and CD-RW SuperMulti Double-Layer Combo Drive specifications ........80 System DMA specifications ........................ 81 System interrupt specifications ......................82 System I/O address specifications ..................... 83 System memory map specifications ....................85 7 Screw listing ..............................
Page 8
10 Power cord set requirements ........................104 Requirements for all countries or regions ..................104 Requirements for specific countries or regions ................105 11 Recycling ..............................106 Battery .............................. 106 Display .............................. 106 Index ................................. 112 viii...
Product description Category Description Product Name HP Pavilion tx2500 Entertainment PC Processors AMD Turion™ 64 Mobile Technology Ultra-Dual Core ZM-86 processor, 2.4-GHz, 2-MB L2 cache, 800-MHz front side bus (FSB) AMD Turion 64 Mobile Technology Ultra-Dual Core ZM-82 processor, 2.2-GHz, 2- MB L2 cache, 800-MHz FSB AMD Turion 64 Mobile Technology Ultra-Dual Core ZM-80 processor, 2.0-GHz, 2-...
Page 10
Category Description 1024-MB total system memory (1024 MB × 1, 512 MB × 2, dual-channel) ● Hard drives Supports all 9.5-mm, 2.5-inch hard drives ● Serial ATA 500-GB, 7200-rpm 320-GB, 7200-rpm 320-GB, 5400-rpm 250-GB, 5400-rpm 160-GB, 5400-rpm ● Optical drives 12.7-mm tray load ●...
Page 11
1394a 2-pin 65-W AC power Docking Docking support through the expansion port 3. Supports the HP xb3000 Notebook Expansion Base and the HP Notebook QuickDock. Keyboard/pointing devices 12.1-inch keyboard with embedded numeric keypad...
Page 12
Category Description AC adapter Battery (system) Hard drive Memory module Optical drive WLAN module Chapter 1 Product description...
External component identification Top components Display components Item Component Function Internal microphones (2) Record sound. Display release latch Opens the computer. Integrated camera (select models only) Records video and captures still photographs. DVD button Launches the DVD playback feature of the QuickPlay program.
Page 14
● Off: The computer is off or in Hibernation. (13) Consumer infrared lens Receives a signal from the HP Remote Control. (14) Internal display switch Turns off the display and initiates Sleep if the display is closed while the power is on.
Keys Item Component Function Displays system information when pressed in combination with the key. Executes frequently used system functions when pressed in combination with a function key or the key. Windows logo key Displays the Windows® Start menu. Windows applications key Displays a shortcut menu for items beneath the pointer.
Pointing devices Item Component Function TouchPad on/off button Enables/disables the TouchPad. TouchPad* Moves the pointer and selects or activates items on the screen. Left TouchPad button* Functions like the left button on an external mouse. ● TouchPad light Blue: TouchPad is enabled. ●...
Blinking: The computer is in the Sleep state. ● Off: The computer is off or in Hibernation. Consumer infrared lens Receives a signal from the HP Remote Control. Audio-out (headphone) S/PDIF jack Provides enhanced audio performance, including surround sound and other high-end audio output.
Item Component Function ● Wireless light Blue: An integrated wireless device, such as a WLAN device and/or a Bluetooth® device, is turned on. ● Amber: All wireless devices are turned off. *This table describes factory settings. For information about changing factory settings, refer to the user guides located in Help and Support.
Right-side components Item Component Function ● Previous/rewind button Plays the previous track or chapter when the button is pressed once. ● Rewinds media when the button is pressed simultaneously with the key. Play/pause button Plays or pauses media. ● Next/fast forward button Plays the next track or chapter when the button is pressed once.
Rear components Item Component Function Vent Enables airflow to cool internal components. NOTE: The computer fan starts up automatically to cool internal components and prevent overheating. It is normal for the internal fan to cycle on and off during routine operation. RJ-11 (modem) jack Connects a modem cable.
Bottom components Item Component Function Vents (6) Enable airflow to cool internal components. NOTE: The computer fan starts up automatically to cool internal components and prevent overheating. It is normal for the internal fan to cycle on and off during routine operation.
Illustrated parts catalog Service tag location The service tag, affixed to the bottom of the computer, provides information that may be needed when troubleshooting system problems. The service tag provides the following information: (1) Product name: This is the product name affixed to the front of the computer. (2) Serial number (s/n): This is an alphanumeric identifier that is unique to each product.
Computer major components Item Description Spare part number (1a) Display assembly 12.1-inch, WXGA, BrightView touch-screen display assembly with Web camera, 484751-001 fingerprint reader, microphones, and WLAN antenna cables Chapter 3 Illustrated parts catalog...
Page 25
Item Description Spare part number 12.1-inch, WXGA, BrightView touch-screen display assembly with Web camera, 484750-001 microphones, and WLAN antenna cables (1b) Display convertible hinge cover (included with display assembly) Display Rubber Kit (not illustrated, includes 8 display bezel rubber screw covers) 464824-001 (2a) Switch cover 464115-001...
Page 26
Item Description Spare part number (7b) Memory module compartment cover (includes 2 captive screws, secured by C-clips) (7c) WLAN module compartment cover (includes 1 captive screw, secured by a C-clip) (7d) Hard drive cover (includes one rubber foot and 2 captive screws, secured by C-clips) (7e) Display connector cover (includes 1 captive screw, secured by a C-clip) (8a)
Page 27
Item Description Spare part number (18) WLAN module Broadcom 4321AGN 802.11a/b/g/n WLAN module ● For use in Canada, the Cayman Islands, Guam, Puerto Rico, 453730-001 the U.S. Virgin Islands, and the United States ● For use in Afghanistan, Albania, Algeria, Andorra, 453730-002 Angola, Antigua and Barbuda, Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan, the Bahamas, Bahrain, Bangladesh, Barbados, Belgium, Belize,...
Page 28
Item Description Spare part number ● For use in Afghanistan, Albania, Algeria, Andorra, Angola, Antigua and Barbuda, Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan, the Bahamas, Bahrain, Bangladesh, Barbados, Belgium, Belize, Benin, Bermuda, Bolivia, Bosnia and Herzegovina, Botswana, Brazil, the British Virgin Islands, Brunei, Bulgaria, Burkina Faso, Burundi, Cameroon, Cape Verde, the Cayman Islands, the Central African Republic, Chad, Chile, Colombia, Comoros, the Congo, Costa Rica, Croatia, Cyprus, the Czech Republic, Denmark, Djibouti, Dominica, the Dominican Republic,...
Page 29
Item Description Spare part number ● For use in Afghanistan, Albania, Algeria, Andorra, 459263-002 Angola, Antigua and Barbuda, Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan, the Bahamas, Bahrain, Bangladesh, Barbados, Belgium, Belize, Benin, Bermuda, Bolivia, Bosnia and Herzegovina, Botswana, Brazil, the British Virgin Islands, Brunei, Bulgaria, Burkina Faso, Burundi, Cameroon, Cape Verde, the Cayman Islands, the Central African Republic, Chad, Chile, Colombia, Comoros, the Congo, Costa Rica, Croatia, Cyprus, the Czech Republic, Denmark, Djibouti, Dominica, the Dominican Republic,...
Mass storage devices Item Description Spare part number Hard drives (include frame and hard drive connector 500-GB, 7200-rpm 634924-001 320-GB, 7200-rpm 603783-001 320-GB, 5400-rpm 622643-001 160-GB, 7200-rpm 579045-001 Hard Drive Hardware Kit (includes hard drive bracket, hard drive connector, and 497744-001 hard drive screws) Optical drive (includes bezel and bracket)
DVB-T TV tuner antenna 412176-003 DVB-T TV tuner antenna adapter 412176-001 HP backpack 405527-001 HP carrying case 418162-001 HP notebook protective sleeve 480105-001 Remote control (fits into ExpressCard slot) 465539-001 Infrared emitter with cable 439129-001 Optical wired mouse 436238-001 Power cord...
405527-001 HP backpack 412175-002 DVB-T TV tuner 412176-001 DVB-T TV tuner antenna adapter 412176-003 DVB-T TV tuner antenna 418162-001 HP carrying case 435836-001 USB travel mouse 436238-001 Optical wired mouse 441131-003 4-cell, 37-Ah, 2.55-Ah battery 441132-003 6-cell, 55-Ah, 2.55-Ah battery...
Page 34
Spare part Description number 449729-001 RTC battery 453730-001 Broadcom 4321AGN 802.11a/b/g/n WLAN module for use in Canada, the Cayman Islands, Guam, Puerto Rico, the U.S. Virgin Islands, and the United States 453730-002 Broadcom 4321AGN 802.11a/b/g/n WLAN module for use in Afghanistan, Albania, Algeria, Andorra, Angola, Antigua and Barbuda, Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan, the Bahamas, Bahrain, Bangladesh, Barbados, Belgium, Belize, Benin, Bermuda, Bolivia, Bosnia and Herzegovina, Botswana, Brazil, the British Virgin Islands, Brunei, Bulgaria, Burkina Faso, Burundi, Cameroon,...
Page 35
Tablet stand 466437-001 Base enclosure (includes optical drive release assembly, 2 battery release latches, and 4 rubber feet) 480105-001 HP notebook protective sleeve 480850-001 System board (includes replacement thermal material) 480864-001 DVD±RW and CD-RW SuperMulti Double-Layer Combo Drive with LightScribe 480865-001 DVD±RW and CD-RW SuperMulti Double-Layer Combo Drive...
Page 36
Spare part Description number 484748-121 Keyboard for use in French Canada 484748-131 Keyboard for use in Portugal 484748-141 Keyboard for use in Turkey 484748-161 Keyboard for use in Latin America 484748-171 Keyboard for use in Saudi Arabia 484748-201 Keyboard for use in Brazil 484748-251 Keyboard for use in Russia 484748-281...
Page 37
Spare part Description number 487926-001 Plastics Kit (see Plastics Kit on page 22 for Plastics Kit spare part information) 490371-001 Power cord for use in the United States 490371-011 Power cord for use in Australia 490371-021 Power cord for use in Europe 490371-031 Power cord for use in the United Kingdom and Singapore 490371-061...
Page 38
Spare part Description number 593028-001 598833-001 512-MB memory module (1-DIMM, PC2-6400, 667-MHz, 800 DDR) 598858-001 2048-MB memory module (1-DIMM, PC2-6400, 667-MHz, 800 DDR) 598861-001 1024-MB memory module (1-DIMM, PC2-6400, 667-MHz, 800 DDR) 603783-001 320-GB, 7200-rpm hard drive 613149-001 65-watt AC adapter 622643-001 320-GB, 5400-rpm hard drive 634256-001...
Removal and replacement procedures Preliminary replacement requirements Tools required You will need the following tools to complete the removal and replacement procedures: ● Magnetic screwdriver ● Phillips P0 and P1 screwdrivers ● Flat-bladed screwdriver Service considerations The following sections include some of the considerations that you should keep in mind during disassembly and assembly procedures.
Cables and connectors CAUTION: When servicing the computer, be sure that cables are placed in their proper locations during the reassembly process. Improper cable placement can damage the computer. Cables must be handled with extreme care to avoid damage. Apply only the tension required to unseat or seat the cables during removal and insertion.
Grounding guidelines Electrostatic discharge damage Electronic components are sensitive to electrostatic discharge (ESD). Circuitry design and structure determine the degree of sensitivity. Networks built into many integrated circuits provide some protection, but in many cases, ESD contains enough power to alter device parameters or melt silicon junctions.
Packaging and transporting guidelines Follow these grounding guidelines when packaging and transporting equipment: ● To avoid hand contact, transport products in static-safe tubes, bags, or boxes. ● Protect ESD-sensitive parts and assemblies with conductive or approved containers or packaging. ● Keep ESD-sensitive parts in their containers until the parts arrive at static-free workstations.
Equipment guidelines Grounding equipment must include either a wrist strap or a foot strap at a grounded workstation. ● When seated, wear a wrist strap connected to a grounded system. Wrist straps are flexible straps with a minimum of one megohm ±10% resistance in the ground cords. To provide proper ground, wear a strap snugly against the skin at all times.
Unknown user password If the computer you are servicing has an unknown user password, follow these steps to clear the password. NOTE: These steps also clear CMOS. Before disassembling the computer, follow these steps: Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
Component replacement procedures This chapter provides removal and replacement procedures. There are as many as 47 screws, in 8 different sizes, that must be removed, replaced, or loosened when servicing the computer. Make special note of each screw size and location during removal and replacement.
Computer feet Description Spare part number Rubber Feet Kit (includes 4 base enclosure rubber feet and pen cover) 464821-001 The computer feet are adhesive-backed rubber pads. There are four computer feet (1) that adhere to the computer base enclosure, and two computer feet (2) that adhere to the high-capacity battery. Chapter 4 Removal and replacement procedures...
Battery Description Spare part number 8-cell, 73-Wh, 2.55-Ah battery 463650-003 6-cell, 55-Wh, 2.55-Ah battery 441132-003 6-cell, 2.55-Ah battery for use in Japan 534133-291 4-cell, 37-Wh, 2.55-Ah battery 441131-003 Before disassembling the computer, follow these steps: Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
Description Spare part number 593028-001 Before removing the pen, follow these steps: Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. Disconnect all external devices connected to the computer.
Hard drive Description Spare part number 500-GB, 7200-rpm 634924-001 320-GB, 7200-rpm 603783-001 320-GB, 5400-rpm 622643-001 160-GB, 7200-rpm 579045-001 Hard Drive Hardware Kit (includes hard drive bracket, hard drive connector, and hard drive 497744-001 screws) Before removing the hard drive, follow these steps: Shut down the computer.
Page 50
Remove the hard drive (2) from the hard drive bay. If it is necessary to remove the hard drive bracket and connector, remove the four Phillips PM3.0×3.0 hard drive bracket screws (1) from each side of the hard drive. Lift the bracket (2) straight up to remove it from the hard drive. Remove the connector (3) from of the hard drive.
Optical drive NOTE: All optical drive spare part kits include an optical drive bezel. Description Spare part number DVD±RW and CD-RW SuperMulti Double-Layer Combo Drive with LightScribe 480864-001 DVD±RW and CD-RW SuperMulti Double-Layer Combo Drive 480865-001 Optical drive weight saving blank 518183-001 Before removing the optical drive, follow these steps: Shut down the computer.
Memory module Description Spare part number 2048-MB (1-DIMM, PC2-5300, 667 MHz) 598858-001 1024-MB (1-DIMM, PC2-5300, 667 MHz) 598861-001 512-MB (1-DIMM, PC2-5300, 667 MHz) 598833-001 Before removing the memory module, follow these steps: Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
Page 53
Pull the module (2) away from the slot at an angle and remove it. NOTE: Memory modules are designed with a notch (3) to prevent incorrect installation into the memory module slot. Reverse this procedure to install a memory module. Component replacement procedures...
WLAN module Description Spare part number Broadcom 4322 802.11a/b/g/n WLAN modules: ● For use in Canada, the Cayman Islands, Guam, Puerto Rico, the U.S. Virgin Islands, 487330-001 and the United States ● For use in Afghanistan, Albania, Algeria, Andorra, Angola, Antigua and Barbuda, 487330-002 Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan, the Bahamas, Bahrain, Bangladesh, Barbados, Belgium, Belize, Benin, Bermuda, Bolivia,...
Page 55
Description Spare part number ● For use in Japan 453730-291 Broadcom BCM4312 802.11b/g WLAN modules: ● For use in Canada, the Cayman Islands, Guam, Puerto Rico, the U.S. Virgin Islands, 459263-001 and the United States ● For use in Afghanistan, Albania, Algeria, Andorra, Angola, Antigua and Barbuda, 459263-002 Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan, the Bahamas, Bahrain, Bangladesh, Barbados, Belgium, Belize, Benin, Bermuda, Bolivia,...
Page 56
Lift the right side of the WLAN module compartment cover (2) and swing it to the left. Remove the WLAN module compartment cover. NOTE: The WLAN module compartment cover is included in the Plastics Kit, spare part number 487926-001. Disconnect the WLAN antenna cables (1) from the WLAN module. NOTE: The black WLAN antenna cable is connected to the WLAN module “Main”...
Keyboard Description Country or region Spare part number Country or region Spare part number Belgium 484748-A41 Portugal 484748-131 Brazil 484748-201 Russia 484748-251 Canada 484748-121 Saudi Arabia 484748-171 Denmark, Finland, and Norway 484748-DH1 South Korea 484748-AD1 France 484748-051 Spain 484748-071 Germany 484748-041 Taiwan 484748-AB1...
Page 58
Open the computer. Lift the rear edge of the keyboard and swing it toward you until it rests on the palm rest. Release the zero insertion force (ZIF) connector (1) to which the keyboard cable is attached and disconnect the keyboard cable (2). Remove the keyboard.
Switch cover Description Spare part number Switch cover (includes display convertible hinge base cover) 464115-001 Before removing the switch cover, follow these steps: Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
Page 60
Rotate the display clockwise approximately 45 degrees. Lift the left and right front corners of the switch cover (1) until it disengages from the computer. Rotate the switch cover (2) counterclockwise and remove it from the computer. Reverse this procedure to install the switch cover. Chapter 4 Removal and replacement procedures...
Display assembly Description Spare part number 12.1-inch, WXGA, BrightView touch-screen display assembly with Web camera, fingerprint 484751-001 reader, microphones, and WLAN antenna cables 12.1-inch, WXGA, BrightView touch-screen display assembly with Web camera, microphones, 484750-001 and WLAN antenna cables Before removing the display assembly, follow these steps: Shut down the computer.
Page 62
Remove the two Phillips PM2.5×6.0 screws (3) that secure the display assembly to the computer. Remove the wireless antenna cables (1) from the routing channel built into the base enclosure. Disconnect the camera cable (2) and the microphone cable (3) from the system board. Turn the computer display-side up, with the front toward you.
Page 63
Disconnect the display panel cable (3) from the system board. NOTE: As you remove the display assembly, be sure that the display cables and wireless antenna cables move cleanly through the opening (1) in the computer. Lift the display (2) straight up and remove it. Reverse this procedure to install the display assembly.
Top cover Description Spare part number Top cover (includes TouchPad and TouchPad cable, caps lock light board and cable, and top 464111-001 cover bumper pads) Before removing the top cover, follow these steps: Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
Page 65
Release the ZIF connector (2) to which the TouchPad cable is connected and disconnect the TouchPad cable (3). Remove the two Phillips PM2.0×4.0 screws (4) that secure the top cover to the base enclosure. Lift the top cover straight up and remove it. Reverse this procedure to install the top cover.
RTC battery NOTE: Removing the RTC battery and leaving it uninstalled for 5 or more minutes causes all passwords and CMOS settings to be cleared. Description Spare part number RTC battery 449729-001 Before removing the RTC battery, follow these steps: Shut down the computer.
Power switch assembly Description Spare part number Power switch assembly (includes power switch board cable and actuator switch) 441142-001 Before removing the power switch assembly, follow these steps: Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
Page 68
Remove the display release hook assembly (3). NOTE: The display release hook assemblies are included with the base enclosure spare part kits. Disconnect the power switch board cable (1) from the system board. Remove the power switch board (2) and power switch actuator (3) from the base enclosure. Reverse this procedure to install the power switch assembly.
Bluetooth module Description Spare part number Bluetooth module 483113-001 Bluetooth module cable 487697-001 Before removing the Bluetooth module, follow these steps: Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. Disconnect all external devices connected to the computer.
Remove the Bluetooth module (3). Reverse this procedure to install the Bluetooth module. System board Description Spare part number System board (includes replacement thermal material) 480850-001 When replacing the system board, be sure that the following components are removed from the defective system board and installed on the replacement system board: ●...
Page 71
Remove the battery (see Battery on page 39). Remove the following components: Hard drive (see Hard drive on page Memory module compartment cover (see Memory module on page Optical drive (see Optical drive on page Keyboard (see Keyboard on page Switch cover (see Switch cover on page Display assembly (see...
Page 72
Release the ZIF connector (1) to which the audio/infrared board cable is connected and disconnect the audio/infrared board cable (2) from the system board. Use the optical drive connector (1) to lift the left side of the system board (2) until the power connector (3) is clear of the base enclosure.
Pen holder and pen eject assembly Description Spare part number Pen holder and pen eject assembly 464113-001 Before removing the pen holder and pen eject assembly, follow these steps: Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
Remove the pen holder (4). Reverse this procedure to install the pen holder and pen eject assembly. Audio/infrared board Description Spare part number Audio/infrared board (includes audio/infrared board cable) 441144-001 Before removing the audio/infrared board, follow these steps: Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
Page 75
System board (see System board on page Pen holder (see Pen holder and pen eject assembly on page Remove the audio/infrared board: Remove the two Phillips PM2.0×3.0 screws (1) that secure the audio/infrared board to the system board. Release the audio/infrared board (2) by sliding it away from you until the connectors on the front of the board disengage from the openings in the base enclosure.
Fan/heat sink assembly Description Spare part number Fan/heat sink assembly (includes thermal paste and thermal pads) 487925-001 NOTE: To properly ventilate the computer, allow at least a 7.6-cm (3-inch) clearance on the right side and rear panel of the computer. The computer uses an electric fan for ventilation.
Page 77
Remove the fan/heat sink assembly (3). NOTE: Due to the adhesive quality of the thermal paste and thermal pads located between the fan/heat sink assembly and system board components, it may be necessary to move the fan/ heat sink assembly from side to side to detach the assembly. NOTE: The thermal paste and thermal pads should be thoroughly cleaned from the surfaces of the fan/heat sink assembly (1) and the system board components (2) each time the fan/heat sink...
Processor NOTE: All processor spare part kits include thermal paste. Desription Spare part number AMD Turion 64 Mobile Technology ZM-86 processor (2.4-GHz, 1-MB L2 cache, 800-MHz FSB) 507974-001 AMD Turion 64 Mobile Technology ZM-84 processor (2.3-GHz, 1-MB L2 cache, 800-MHz FSB) 507957-001 AMD Turion 64 Mobile Technology ZM-82 processor (2.2-GHz, 1-MB L2 cache, 800-MHz FSB) 507973-001...
Page 79
Lift the processor (2) straight up and remove it. NOTE: The gold triangle (3) on the processor should be aligned with the triangle (4) embossed on the processor socket when you install the processor. Reverse this procedure to install the processor. Component replacement procedures...
Setup Utility WARNING! Only authorized technicians trained by HP should repair this equipment. All troubleshooting and repair procedures are detailed to allow repair at only the subassembly or module level. Because of the complexity of the individual boards and subassemblies, do not attempt to make repairs at the component level or modify any printed wiring board.
Changing the language of the Setup Utility The following procedure explains how to change the language of the Setup Utility. If the Setup Utility is not already running, begin at step 1. If the Setup Utility is already running, begin at step 2. To start the Setup Utility, turn on or restart the computer, and then press while “Press <F10>...
Restoring default settings in the Setup Utility The following procedure explains how to restore the Setup Utility default settings. If the Setup Utility is not already running, begin at step 1. If the Setup Utility is already running, begin at step 2. To start the Setup Utility, turn on or restart the computer, and then press while “Press <F10>...
Closing the Setup Utility You can close the Setup Utility with or without saving changes. ● To close the Setup Utility and save your changes from the current session, use either of the following procedures: ◦ Press f10, and then follow the instructions on the screen. —...
System Configuration menu Select To do this Language Support Change the Setup Utility language. Enhanced SATA support (select models only) Enable/disable enhanced SATA mode. Boot Options Set the following boot options: ● Delay (sec.)―Set the delay for the functions of the Setup Utility in intervals of 5 seconds each (0, 5, 10, 15, 20).
Specifications Computer specifications Metric U.S. Dimensions Height (front to back) 3.1 to 3.9 cm 1.22 to 1.54 in Width 30.6 cm 12.05 in Depth 22.4 cm 8.82 in Weight (with optical drive, hard drive, 1.95 kg 4.29 lbs and battery) Input power Operating voltage 18.5 V dc @ 3.5 A - 65 W...
Metric U.S. Nonoperating 1.50 g zero-to-peak, 10 Hz to 500 Hz, 0.5 oct/min sweep rate NOTE: Applicable product safety standards specify thermal limits for plastic surfaces. The computer operates well within this range of temperatures. 12.1-inch, WXGA BrightView display specifications Metric U.S.
Hard drive specifications 320-GB* 250-GB* 160-GB* 120-GB* Dimensions Height 9.5 mm 9.5 mm 9.5 mm 9.5 mm Width 70 mm 70 mm 70 mm 70 mm Weight 101 g 101 g 101 g 101 g Interface type ATA-7 ATA-7 ATA-7 ATA-7 Transfer rate Synchronous (maximum)
System DMA specifications Hardware DMA System function DMA0 Not applicable DMA1* Not applicable DMA2* Not applicable DMA3 Not applicable DMA4 Direct memory access controller DMA5* Available for PC Card DMA6 Not assigned DMA7 Not assigned *PC Card controller can use DMA 1, 2, or 5. System DMA specifications...
System interrupt specifications Hardware IRQ System function IRQ0 System timer IRQ1 Standard 101-/102-Key or Microsoft® Natural Keyboard IRQ2 Cascaded IRQ3 USB2 Enhanced Host Controller—24CD IRQ4 COM1 IRQ5* Conexant AC—SMBus Controller—24C3 Data Fax Modem with SmartCP IRQ6 Diskette drive IRQ7* Parallel port IRQ8 System CMOS/real-time clock IRQ9*...
Screw listing This section provides specification and reference information for the screws and screw locks used in the computer. All screws and screw locks listed in this section are available in the Screw Kit, spare part number 464116-001. Phillips PM3.0×3.0 screw Color Quantity Length...
Phillips PM2.0×7.0 screw Color Quantity Length Thread Head width Black 7.0 mm 2.0 mm 4.5 mm Where used: 4 screws that secure the switch cover to the computer Where used: 5 screws that secure top cover to the computer Phillips PM2.0×7.0 screw...
Phillips PM2.0×4.0 screw Color Quantity Length Thread Head width Silver 4.0 mm 2.0 mm 4.5 mm Where used: 2 screws that secure the top cover to the computer Where used: 2 screws that secure the power switch board to the base enclosure Chapter 7 Screw listing...
Page 97
Where used: 2 screws that secure the audio/infrared board to the base enclosure Where used: 4 screws that secure the fan/heat sink assembly to the system board Phillips PM2.0×4.0 screw...
Phillips PM2.0×5.0 captive screw Color Quantity Length Thread Head width Black 5.0 mm 2.0 mm 4.5 mm Where used: (1) Two captive screws (secured by C-clips) that secure the hard drive cover to the computer (2) Two captive screws (secured by C-clips) that secure the memory module compartment cover to the computer (3) One captive screw (secured by a C-clip) that secures the WLAN module compartment cover to the computer...
Black Phillips PM2.0×3.0 screw Color Quantity Length Thread Head width Black 3.0 mm 2.0 mm 4.5 mm Where used: 2 screws that secure the WLAN module to the computer Where used: 3 screws that secure the top cover to the base enclosure Black Phillips PM2.0×3.0 screw...
Phillips PM2.0×11.0 screw Color Quantity Length Thread Head width Black 11.0 mm 2.0 mm 4.5 mm Where used: 4 screws that secure the keyboard to the computer Chapter 7 Screw listing...
Phillips PM2.5×6.0 screw Color Quantity Length Thread Head width Silver 6.0 mm 2.5 mm 5.0 mm Where used: 2 screws that secure the display assembly to the computer Where used: 2 screws that secure the display assembly to the computer Phillips PM2.5×6.0 screw...
Silver Phillips PM2.0×3.0 screw Color Quantity Length Thread Head width Silver 3.0 mm 2.0 mm 4.5 mm Where used: (1) One screw that secures the display release hook to the base enclosure (2) One screw that secures the Bluetooth module to the base enclosure Where used: 3 screws that secure the pen eject assembly and pen holder to the base enclosure Chapter 7 Screw listing...
Backup and recovery Recovering system information Tools provided by the operating system and Recovery Manager software are designed to help you with the following tasks for safeguarding your information and restoring it in case of a system failure: ● Backing up your information regularly to protect your important system files. ●...
● Number each disc before inserting it into the computer optical drive. ● If necessary, you can exit the program before you have finished creating the recovery discs. The next time you open Recovery Manager, you will be prompted to continue the disc creation process.
Backup suggestions ● Create a set of recovery discs using Recovery Manager. ● Create system restore points using the Windows System Restore feature, and periodically copy them to disc. ● Store personal files in the Documents folder and back up these folders periodically. ●...
Click Create. The System Protection window opens. Follow the on-screen instructions. Restore to a previous date and time To revert to a restore point (created at a previous date and time), when the computer was functioning optimally, follow these steps: Select Start >...
Page 107
To restore the system from the partition, follow these steps: Access Recovery Manager in either of the following ways: ● Select Start > All Programs > Recovery Manager > Recovery Manager. –or– ● Restart the computer and press while the “Press <F11> for recovery” message is displayed on the screen.
Connector pin assignments Audio-out (headphone) Signal Audio out, left channel Audio out, right channel Ground Audio-in (microphone) Signal Audio signal in Audio signal in Ground 100 Chapter 9 Connector pin assignments...
External monitor Signal Red analog Green analog Blue analog Not connected Ground Ground analog Ground analog Ground analog +5 VDC Ground Monitor detect DDC 2B data Horizontal sync Vertical sync DDC 2B clock External monitor 101...
S-Video-out Signal S-VHS color (C) signal Composite video signal S-VHS intensity (Y) signal S-VHS color ground TV-CD S-VHS intensity ground Composite video ground Universal Serial Bus Signal +5 VDC Data - Data + Ground S-Video-out 103...
10 Power cord set requirements The wide range input feature of the computer permits it to operate from any line voltage from 100 to 120 volts AC or from 220 to 240 volts AC. The 3-conductor power cord set included with the computer meets the requirements for use in the country or region where the equipment is purchased.
Requirements for specific countries or regions Region Accredited agency Applicable note number Australia EANSW Austria Belgium CEBC Canada Denmark DEMKO Finland FIMKO France Germany Italy Japan METI The Netherlands KEMA Norway NEMKO The People's Republic of China South Korea Sweden SEMKO Switzerland Taiwan...
Careful handling should be exercised when removing these components. NOTE: Materials Disposal. This HP product contains mercury in the backlight in the display assembly that might require special handling at end-of-life. Disposal of mercury may be regulated because of environmental considerations. For disposal or recycling information, contact your local authorities, or see the Electronic Industries Alliance (EIA) Web site at http://www.eiae.org.
Page 115
Perform the following steps to disassemble the display assembly: Remove all screw covers (1) and screws (2) that secure the display bezel to the display assembly. Lift up and out on the left and right inside edges (1) and the top and bottom inside edges (2) of the display bezel until the bezel disengages from the display assembly.
Page 116
Disconnect all display panel cables (1) from the display inverter and remove the inverter (2). Remove all screws (1) that secure the display panel assembly to the display enclosure. Remove the display panel assembly (2) from the display enclosure. Turn the display panel assembly upside down. Remove all screws that secure the display panel frame to the display panel.
Page 117
Remove the display panel frame (2) from the display panel. Remove the screws (1) that secure the backlight cover to the display panel. Lift the top edge of the backlight cover (2) and swing it outward. Remove the backlight cover. Turn the display panel right-side up.
Page 118
Remove the backlight cables (1) from the clip (2) in the display panel. Turn the display panel upside down. Remove the backlight frame from the display panel. WARNING! The backlight contains mercury. Exercise caution when removing and handling the backlight to avoid damaging this component and causing exposure to the mercury. Remove the backlight from the backlight frame.
Page 119
Disconnect the display cable (1) from the LCD panel. Remove the screws (2) that secure the LCD panel to the display rear panel. Release the LCD panel (3) from the display rear panel. Release the tape (4) that secures the LCD panel to the display rear panel. Remove the LCD panel.
Index Bluetooth module cable rear 12 AC adapter, spare part number spare part number 28 right-side 11 24, 30 Bluetooth module cable, spare part computer feet administrator password 75 number 17, 61 locations 38 advanced Setup Utility features boot options 76 spare part number 18, 27, 38 boot order 76 computer specifications 77...
Page 122
microphones 5 Plastics Kit ports 3 Mobility Center button 5 contents 22 power requirements 3 model name 1 spare part number 17, 22, 29 processors 1 modem jack play/pause button 11 product name 1 location 12 pointing devices security 3 pin assignments 102 components 8 serviceability 3...
Page 123
service considerations 31 service tag 14, 37 Tablet stand, spare part number serviceability, product 25, 27 description 3 thermal pad kit, spare part Setup Utility number 30, 69 changing the language 73 thermal paste, replacement 69 Diagnostics menu 76 tools required 31 displaying system information top cover removal 56...