Table of Contents
Advertisement
CABINET DISASSEMBLY INSTRUCTIONS
1. Disassembly Flowchart
This flowchart indicates the disassembly steps to gain
access to item(s) to be serviced. When reassembling,
follow the steps in reverse order. Bend, route, and
dress the cables as they were originally.
[1] Top Case
[2] Front Assembly
[4] Reinforce Plate
[5] DVD Main CBA Unit
[6] DVD Mecha
2. Disassembly Method
ID/
LOC.
PART
Fig.
No.
No.
[1]
Top Case
D1
Front
[2]
D2
Assembly
[3]
Tray Panel D2
Reinforce
[4]
D3
Plate
DVD Main
[5]
D4
CBA Unit
DVD
D4,
[6]
Mecha
D5
[7]
AV CBA
D6
Function
[8]
D6
CBA
↓
↓
↓
(1)
(2)
(3)
[3] Tray Panel
[7] AV CBA
[8] Function CBA
REMOVAL
REMOVE/*UNHOOK/
UNLOCK/RELEASE/
Note
UNPLUG/DESOLDER
3(S-1)
*4(L-1), *3(L-2),
1-1
*3(L-3)
1-2
*2(L-4)
3(S-2)
(S-3A), (S-3B)
*CN201, *CN301,
2-1
2-2
*CN401, *CN601
4(S-4)
(S-5), 4(S-6), *2(L-5)
*CN2001
↓
(4)
(5)
(1): Identification (location) No. of parts in the figures
(2): Name of the part
(3): Figure Number for reference
(4): Identification of parts to be removed, unhooked,
unlocked, released, unplugged, unclamped, or
desoldered.
P=Spring, L=Locking Tab, S=Screw,
CN=Connector
*=Unhook, Unlock, Release, Unplug, or Desolder
e.g. 2(S-2) = two Screws (S-2),
2(L-2) = two Locking Tabs (L-2)
(5): Refer to "Reference Notes."
About tightening screws
When tightening screws, tighten them with the follow-
ing torque.
Screws
(S-1), (S-2), (S-3A),
(S-4), (S-5), (S-6)
(S-3B)
Reference Notes
CAUTION 1: Locking Tabs (L-1), (L-2), (L-3) and (L-4)
are fragile. Be careful not to break them.
1-1. Release four Locking Tabs (L-1). Then, release
-
three Locking Tabs (L-2).
1
1-2. Release three Locking Tabs (L-3). Then remove
the Front Assembly.
CAUTION 2: Electrostatic breakdown of the laser
1
diode in the optical system block may occur as a
potential difference caused by electrostatic charge
-
accumulated on cloth, human body etc, during
unpacking or repair work.
2
To avoid damage of pickup follow next procedures.
2-1. Short the three short lands of FPC cable with sol-
der before removing the FFC cable (CN201) from
2
it. If you disconnect the FFC cable (CN201), the
3
laser diode of pickup will be destroyed. (Fig. D4)
-
2-2. Disconnect Connectors (CN301), (CN401) and
(CN601). Remove two Screws (S-3A) and (S-3B)
-
and lift the DVD Main CBA Unit. (Fig. D4)
CAUTION 3: When reassembling, confirm the FFC
↓
cable (CN201) is connected completely. Then remove
the solder from the three short lands of FPC cable.
(Fig. D4)
1-5-1
Torque
0.45 ± 0.05 N·m
0.38 ± 0.04 N·m
E5900DC
Advertisement
Table of Contents
