Specifications; Operation - Husky DPP123 Manual

Respect the tool as a working implement.
Never engage in horseplay.
Never pull the trigger unless nose is directed
toward the work.
Keep others a safe distance from the tool
while tool is in operation as accidental
actuation may occur, possibly causing injury.
AIR SUPPLY AND CONNECTIONS
● The connector on the tool must not hold
pressure when air supply is disconnected.
an incorrect fitting is used, the tool can remain
charged with air after disconnecting and thus will
be able to drive a fastener even after the air line
is disconnected, possibly causing injury.
●
Do not use any type of reactive gases,
including, but not limited to, oxygen and
combustible gases, as a power source.
filtered, lubricated, regulated compressed air
only. Use of a reactive gas instead of
compressed air may cause the tool to explode
which will cause death or serious personal injury.
● Use only a pressure-regulated compressed
air source to limit the air pressure supplied to
the tool. The regulated pressure must not
exceed 100psi. If the regulator fails, the pressure
delivered to the tool must not exceed 200psi.
Always disconnect air source:
●
◆Before unloading or making adjustments.
◆When maintaining the tool.
◆When clearing a jam.
◆ When touching the safety yoke.
◆When tool is not in use.
◆When moving to a different work area.
Such precautionary measures reduce the risk
of injury to persons.
LOADING TOOL
●
Do not load the tool with fasteners when any
one of the operating controls is activated.
● Never place a hand or any part of body in
fastener discharge area of tool.
● Never point tool at anyone.
● Do not pull the trigger or depress the
workpiece contact as accidental actuation
may occur, possibly causing injury.
06
WARNING:
!
The warnings and precautions discussed
above cannot cover all possible
conditions and situations that may occur.
It must be understood by the user that
common sense and caution are factors
which cannot be built into this product,
but must be supplied by the user.
UNPACKING
If
● This tool has been shipped completely
assembled.
●
Make sure that all items listed in the packing
list are included.
Carefully remove the tool and any
●
Use
accessories from the box.
Inspect the tool carefully to make sure no
●
breakage or damage occurred during
shipping.
● Do not discard the packing material until you
have carefully inspected and satisfactorily
operated the tool.
● If any parts are damaged or missing, please
call 1-866-676-8468 .
WARNING:
!
If any parts are missing do not operate
this tool until the missing parts are
replaced. Failure to do so could result in
possible serious personal injury.
WARNING:
!
Do not attempt to modify this tool or
create accessories not recommended
for use with this tool. Any such
alteration or modification is misuse
and could result in hazardous condition
leading to possible serious personal
injury.
FEATURES

SPECIFICATIONS

REQUIRES: 1.36 SCFM with 100
fasteners per minute @ 80psi
AIR INLET: 1/4 inch NPT
MAGAZINE CAPACITY:
100 headless pins, 23 gauge
WEIGHT: 2.24 lbs
MAXIMUM PRESSURE: 100psi
–
PRESSURE RANGE: 60psi 100psi
PIN SIZE RANGE: 1/2 inch to 1 inch
1 /2 "
12mm
16mm 5/8"
19mm 3/4"
22mm 7/8"
25mm
1"
Compatible with All Brands 23 Gauge Micro Pins.
FEATURES
● 360 ADJUSTABLE EXHAUST °
Allows user to direct air away from face .
●
COMFORT-GRIP HANDLE
For increased comfort and control.
● ERGONOMICALLY ENGINEERED BODY
Rugged and Comfortable face resulting in a light-
weight tool great for extended use.
●
DUAL TRIGGER
Safety for users.
●
NON-MARRING SAFETY CONTACT
Eliminates damage to working surface.

OPERATION

ADJUSTING THE EXHAUST
The adjustable exhaust on the cap of the tool allows
users to direct the exhaust according to operator
preference. To adjust the direction, turn the exhaust
cap in the desired direction.
LOADING FASTENERS
⒈ Connect the tool to the air source.
⒉ Set the pin length adjustment switch( ) to the
A
appropriate setting for the length of pins you are
loading by first pushing in on the orange
switch( ) and sliding until the notch is in the
A
appropriate groove.
Length adjustment switch(A)
⒊ Push the latch button(B). Pull back on the
magazine cover fully(C).
Latch
button(B)
07