Gree GWH09QB-K3DNA6G Service Manual page 32

Service Manual
● Under swing left and right mode, when the status is switched from off to
status directly; if press this button again within 2s, the change of swing status will also depend on the circulation sequence stated above.
7. button
Press this button can select up & down swing angle. Fan blow angle can be selected circularly as below:
● When selecting " ", air conditioner is blowing fan automatically. Horizontal louver will automatically swing up & down at maximum angle.
● When selecting "
、 、
● When selecting " 、 、 " , air conditioner is blowing fan at fixed angle. Horizontal louver will send air at the fixed angle.
● Hold " "button above 2s to set your required swing angle. When reaching your required angle, release the button.
Note:
● " 、 、 " may not be available. When air conditioner receives this signal, the air conditioner will blow fan automatically.
● Press this button continuously more than 2s, the main unit will swing back and forth from up to down, and then loosen the button, the unit
will stop swinging and present position of guide louver will be kept immediately.
● Under swing up and down mode, when the status is switched from off to
status directly; if press this button again within 2s,the change of swing status will also depend on the circulation sequence stated above.
8. SLEEP button
Under COOL, HEAT or DRY mode, press this button to start up sleep function. "
again to cancel sleep function and "
function is canceled. In this mode, the time of time can be adjusted. Under Fan and Auto modes, this function is not available.
9. I FEEL button
Press this button to start I FEEL function and "
will send the detected ambient temperature to the controller and the unit will automatically adjust the indoor temperature according to the
detected temperature. Press this button again to close I FEEL function and "
● Please put the remote controller near user when this function is set. Do not put the remote controller near the object of high temperature
or low temperature in order to avoid detecting inaccurate ambient temperature.
10. TIMER ON / TIMER OFF button
● TIMER ON button
"TIMER ON" button can set the time for timer on. After pressing this button, "
blinks. Press " ▲ " or "
or decrease 1min. Hold " ▲ " or "
confirm it. The word "ON" will stop blinking. "
up, press "TIMER ON" button to cancel it.
● TIMER OFF button
"TIMER OFF" button can set the time for timer off. After pressing this button,"
blinks. Press " ▲ " or "
or decrease 1min. Hold " ▲ " or "
word "OFF" will stop blinking. "
"TIMER OFF" button to cancel it.
Note:
● Under on and off status, you can set TIMER OFF or TIMER ON simultaneously.
● Before setting TIMER ON or TIMER OFF, please adjust the clock time.
● After starting up TIMER ON or TIMER OFF, set the constant circulating valid. After that, air conditioner will be turned on or turned off
according to setting time. ON/OFF button has no effect on setting. If you don't need this function, please use remote controller to cancel it.
11. CLOCK button
Press this button to set clock time. "
pressing of " ▲ " or " " button, clock time will increase or decrease 1 minute. If hold " ▲ " or "
Release this button when reaching your required time. Press "CLOCK" button to confirm the time. "
Note:
● Clock time adopts 24-hour mode.
● The interval between two operation can't exceeds 5s. Otherwise, remote controller will quit setting status. Operation for TIMER ON/TIMER
OFF is the same.
Technical Information
no display
(horizontal louvers stops
at current position)
、 、 ", air conditioner is blowing fan at fixed position. Horizontal louver will stop at the fixed position.
" icon will disappear.After powered on,Sleep Off is defaulted. After the unit is turned off, the Sleep
" will be displayed on the remote controller. After this function is set, the remote controller
"button to adjust TIMER ON setting. After each pressing " ▲ " or "
" button, 2s later, the time will change quickly until reaching your required time. Press "TIMER ON" to
" icon resumes displaying. Cancel TIMER ON: Under the condition that TIMER ON is started
" button to adjust TIMER OFF setting. After each pressing " ▲ " or "
" button, 2s later, the time will change quickly until reaching your required time. Press "TIMER OFF"
" icon resumes displaying. Cancel TIMER OFF. Under the condition that TIMER OFF is started up, press
" icon on remote controller will blink. Press " ▲ " or "
, if press this button again 2s later,
, if press this button again 2s later,
" icon is displayed on remote controller. Press this button
" will disappear.
" icon disappears and the word "ON" on remote controller
" button, TIMER ON setting will increase
"icon disappears and the word "OFF" on remote controller
" button, TIMER OFF setting will increase
" button within 5s to set clock time. Each
" button, 2s later, time will change quickly.
" icon stops blinking.
status will switch to off
status will switch to off
29