Television Video Cassette Recorder Chassis : C15A Model: TW14C52S/BWT Television Video Cassette Recorder CONTENTS Precautions Specifications Disassembly and Reassembly Alignment and Adjustment (Mechanical) Alignment and Adjustment (Electrical) Troubleshooting Exploded View and Parts List Electric Parts List Block Diagram PCB Layout...
The current measured should the XÐray Protection Specifications Label, and not exceed 0.5 milliamp. Reverse the power- the Product Safety and X-ray Warning Note on plug prongs in the AC outlet and repeat the the service data schematic. test. Samsung Electronics...
Page 3
14. Components, parts and wiring that appear to have overheated or that are otherwise damaged should be replaced with parts that meet the original specifications. Always determine the cause of damage or overheat- ing, and correct any potential hazards. Samsung Electronics...
Page 4
Make sure that the portion around the serviced part has not been damaged. 8. Always connect a test instrumentÕs ground lead to the instrument chassis ground before connecting the positive lead; always remove the instrumentÕs ground lead last. Samsung Electronics...
Page 5
4. Do not use freon-propelled chemicals. These unpackaged replacement ESDs. Motions such can generate electrical charges that damage as brushing clothes together, or lifting a foot ESDs. from a carpeted floor can generate enough static electricity to damage an ESD. Samsung Electronics...
14” (368.5 x 388 x 381) 20” (488 x 477 x 488) 21” (520 x 495 x 508) Weight 14” (11.7 kg) 20” (20.4 kg) 21” (23.2 kg) Operating temperature 5°C - 40°C (41°F - 104°F) Relative humidity 10% - 75% Samsung Electronics...
Disassembly and Reassembly 3. Disassembly and Reassembly 3-1 Disassembly 3-1-1 Back Cover Removal 1. Remove the screws located on the side of the back cover. Samsung Electronics...
Page 8
Disassembly and Reassembly 3-1-2 Main Assembly Removal 1. Release two connectors between sub PCB and Main Assembly. 2. Pull the Main Assembly backwards to remove. Samsung Electronics...
Page 9
Disassembly and Reassembly 3-1-3 Monitor Frame Removal 1. Remove 3 screws from the Main Assembly. Remove the dust cover. 2. Remove 4 screws from the Deck Assembly. Samsung Electronics...
Page 10
1. Remove 2 screws holding the upper chassis housing. 2. Remove one screw from Main PCB Assembly. Take off the deck Assembly. 2. Remove 3 screws holding the deck assembly. 3. Lift the deck assembly upward to remove. Samsung Electronics...
Page 11
1. Remove two (2) screws located at the rear of the top cabinet. 2. Carefully lift the back of the top cabinet and shield it to the rear to remove. 3-1-7 Top Cabinet Removal 3-1-8 Top Cabinet Removal Samsung Electronics...
Page 12
¨ Ø ∏ Fig. 4-1 Top parts Location-1 Œ BRACKET FL TOP ´ GEAR FL CAM ˇ MOTOR LOADING ASS’Y ¨ LEVER FL ARM ASS’Y ˆ HOLDER FL CASSETTE ASS’Y Ø LEVER FL DOOR ∏ SLIDER FL DRIVE Samsung Electronics...
Page 13
¨ PLATE CYLINDER B Ò GEAR IDLE ˆ PLATE CYLINDER A Ú LEVER IDLE Ø ACE HEAD ASS’Y Æ LEVER T BRAKE ASS’Y ∏ UNIT PINCH ASS’Y ı DISK T REEL ” LEVER #9 GUIDE ASS’Y ’ LEVER TENSION ASS’Y Samsung Electronics...
Page 14
” HOLDER CLUTCH ASS’Y ´ GEAR JOINT 2 ’ BELT PULLEY ˇ BRAKET GEAR ˝ SLIDER CAM ¨ MOTOR CAPSTAN ASS’Y Ô SLEEVE TENSION ˆ LEVER T LOAD ASS’Y Ø GEAR LOADING DRIVE ∏ LEVER S LOAD ASS’Y Samsung Electronics...
Page 15
Note : Take care not to change assembly direction. Œ in the direction of arrow ÒBÓ. Œ 2 SCREWS ´ BRACKET FL TOP Œ LEVER FL DOOR "A" "B" ´ HOOK FIG.1 Fig. 4-5 Lever FL Door Removal Fig. 4-4 Braket FL Top Removal Samsung Electronics...
Page 16
¨ LEVER FL RAIL [D] CASSETTE ASS'Y ARM ASS'Y ´ LEVER FL CASSETTE-R "A" GROOVE [A] BOSS [A] ´ BOSS ˇ SLIDER FL DRIVE Fig. 4-6 Holder FL Cassette Ass’y Removal Fig. 4-7 Lever FL Arm Ass’y Removal Samsung Electronics...
Page 18
ˇ GEAR WORM WHEEL TIMING POINT 1 TIMING POINT 2 Fig. 4-11 Holder Worm, Gear Worm, Gear Worm Wheelemoval ¨ GEAR FL CAM POST GEAR WORM WHEEL TIMING POINT 3 Fig. 4-10 Assembly of Gear FL Cam, Gear Joint 1,2 Samsung Electronics...
Page 19
4. Remove the Lever T, S Load AssÕy ˇ, ¨. Œ GEAR LOADING DRIVE HOOK [A] ´ SLIDER CAM ˇ LEVER T LOAD ASS'Y ¨ LEVER S LOAD ASS'Y Fig. 4-13 Gear Loading Drive, Slider Cam, Lever T, S Load Ass’y Removal Samsung Electronics...
Page 20
PIN A PIN C PIN D PIN B ˇ SLIDER CAM Fig. 4-14 Assembly of Gear Loading Drive, Slider Cam, Lever T, S Load Ass’y ´ SLEEVE TENSION Fig. 4-15 Lever Tension Ass’y, Band Brake Ass’y, Sleeve Tension Removal Samsung Electronics...
Page 21
ˇ SPRING BRAKE HOOK [C] ´ GEAR IDLE "B" ´ LEVER T BRAKE ASS'Y ´ GEAR IDLE Œ LEVER S BRAKE ASS'Y HOOK [B] Fig. 4-17 Lever Idle Ass’y Removal Fig. 4-16 Lever S, T Brake Ass’y Removal 4-10 Samsung Electronics...
Page 23
Œ LEVER UP DOWN ASS'Y ¨ RING ˇ GEAR ∏ HOOK 35˚ Ø POST MAIN BASE Fig. 4-20 Lever Up Down Ass’y, Gear Center Ass’y Removal Fig. 4-21 Assembly of Lever Up Down Ass’y, Gear Center Ass’y 4-12 Samsung Electronics...
Page 24
2. When reinstalling, be sure to apply grease on the post pinch roller. HOOK [A] ´ PLATE JOINT Œ UNIT PINCH ASS'Y ˇ SPRING PINCH DRIVE Fig. 4-22 Guide Cassette Door Removal Fig. 4-23 Unit Pinch Ass’y, Plate Joint, Spring Pinch Drive Removal Samsung Electronics 4-13...
Page 25
2. After reinstalling, check the bottom side of the Post #9 Guide to stick to the top side of Main Base. ´ LEVER #9 GUIDE ASS'Y Œ SPRING #9 GUIDE Fig. 4-25 FE Head Removal Fig. 4-24 Lever #9 Guide Ass’y Removal 4-14 Samsung Electronics...
Page 26
4-2-24 Slider S, T Ass’y Removal 1. Move the Slider S, T AssÕy Œ, ´ to slot, and then lift it to remove. (Refer to arrow) Œ SLIDER S ASS'Y ´ SLIDER T ASS'Y Fig. 4-27 Slider S, T Ass’y Removal Samsung Electronics 4-15...
Page 27
4-2-27 Lever Head Cleaner Ass’y Removal (Optional) 1. Release the Hook Œ. 2. Lift the Lever Head Cleaner AssÕy ´. ´ LEVER HEAD CLEANER ASS'Y Œ HOOK Fig. 4-28 Cylinder Ass’y Removal Fig. 4-30 Lever Head Cleaner Ass’y Removal 4-16 Samsung Electronics...
Page 28
4. Rotate Gear Worm Wheel ˇ counterclockwise using screw driver, up to the state of eject mode, and then pick out the tape. (Refer to Fig. 4-32) ´ MOTOR CAPSTAN ASS'Y Fig. 4-31 Motor Capstan Ass’y Removal FRAME Fig. 4-33 Samsung Electronics 4-17...
Page 29
CAPSTAN MOTOR PULLEY BELT PULLEY ∆ HOLDER CLUTCH ASS’Y GEAR CENTER ASS’Y GEAR IDLE (2Point) LOADING MOTOR BAND BRAKE ASS’Y BRAKE T ASS’Y Æ : Cleaning O : Check and replacement in necessary 3 : Add Oil 4-18 Samsung Electronics...
Page 30
Fig. 4-4-1 Location of Tape Transport Adjustment FE HEAD CYLINDER ASS'Y PINCH ROLLER GUIDE ROLLER "S" GUIDE ROLLER "T" POST TENSION #8 GUIDE POST #9 GUIDE POST MAIN BASE ACE HEAD CAPSTAN SHAFT #3 GUIDE POST Fig. 4-4-2 Tape Travel Diagram Samsung Electronics 4-19...
Page 31
TLIT ADJUST X-POSITION ADJUSTING SLIT SCREW (B) SCREW (D) AZIMUTH ADJUST X-POSITION LOCKING Fig. 4-5-1 Location of ACE Head Adjustment Screw AUDIO HEAD VIDEO HEAD 0 ~ 0 .25 mm CONTROL HEAD Fig. 4-5-2 ACE Head Height Adjustment 4-20 Samsung Electronics...
Page 32
CONTROL PULSE REMOVE BUTTONS damaged, do not adjust X-point by using force. After turning the X-point adjusting screw (D) PUSH slightly counterclockwise, perform the adjustment and then tighten the screw. FINE FINE PUSH Fig. 4-5-5 Control Pulse Adjustment Samsung Electronics 4-21...
Page 33
CONTROL PULSE REMOVE CH-2 = 0.2V BUTTONS PUSH CH-2 PROBE H'D SW PULSE FINE FINE CH-1 PROBE CTL PULSE PUSH 4H'd : 7msec 2H'd : 2mesc Fig. 4-5-6 racking Preset and Control Adjustment Only for Models: sv-70U/90U/120U/140U/160U VR5805/VR5855/5905/8905 4-22 Samsung Electronics...
Page 34
) driver to obtain a flat video RF envelope as shown in Fig. 4-5-9. IDEAL ENVELOPE S HEIGHT S HEIGHT T HEIGHT T HEIGHT TOO HIGH TOO LOW TOO HIGH TOO LOW GUIDE ROLLER T GUIDE ROLLER S Fig. 4-5-9 Guide Roller S, T Height Adjustment Samsung Electronics 4-23...
Page 35
3. Brake is operated by slider cam at FF/REW mode. 145 ± 30 Cassette Torquemeter 4. Transportation of accurate driving force is done by gears. (Gear Center AssÕy) Note : If the specifications are not met, replace the holder clutch assÕy and then recheck. 4-24 Samsung Electronics...
Page 36
Fig. 4-5-14 Tension Pole and Back Tension Adjustment Note : 1 Mark on Main Base is located about 1.3mm from inside of curved line. 2 Be careful not to deform the region of adjustment around the Main Base (up or down). Samsung Electronics 4-25...
Adjustment, Option Bytes and Reset. 3. Access the Adjustment Mode by pressing the ÒVOLUMEÓ keys ( Up or Down). The adjust- ment parameters are listed in the accompany- ing table, and selected by pressing the CHAN- NEL keys ( , ). Samsung Electronics...
Page 38
"FACTORY" key . Even if the TV power is cut off, the Aging Mode is not cancelled. The "AGING" marking is displayed on the screen. The AGING mode is cancelled by repressing the "FACTORY" key. Samsung Electronics...
Page 39
NOT USED (DEFAULT OPERATION = WEST, SCAN) Note 1: United Kingdom: 468 - 900MHz (UHF only) Others: 40 - 900 MHz Note 2: Color decoder mode is always "auto" MODULATION STANDARD COLOUR DECODER MODE SYSTEM NEGATIVE AUTO PAL/SECAM FRANCE POSITIVE AUTO Samsung Electronics...
Page 40
Function Reset : After Factory Reset, the following items revert to their initial values. Volume )))) Program Channel))) P-STD)))) MEMORY Auto Power))) NR)))) Reserved Timer Recording) ALL CLEAR Skip (Store/Clear))) ALL CLEAR Caution : When the EEPROM is replaced, all items revert to their initial values. Samsung Electronics...
Page 41
2. Turn on the TV. Set the Brightness and Contrast controls to minimum (zero beam current). 3. The high voltage should not exceed 27.5KV. 4. Adjust the Brightness and contrast controls to both extremes. Ensure that the high voltage does not exceed 27.5KV under any conditions. Samsung Electronics...
Page 42
9. Slowly move the deflection yoke forward, and adjust for the best overall green screen. 10. Temporarily tighten the deflection yoke. 11. Produce blue and red rasters by adjusting the low-light controls. Check for good purity in each field. 12. Tighten the deflection yoke. Samsung Electronics...
Page 43
1. Input either a Lion Head or a Òpure whiteÓ pattern. 2. Warm up the TV for 30 minutes. 3. Check the data in the Service Mode 4. Adjust RG, BG in the Factory Mode. 5-4-7 (B) LOW-LIGHT ADJUSTMENT 1. Automatically accomplished during the high-light adjustment. Samsung Electronics...
Page 44
Connect DC Voltmeter to AFT terminal of TUNER IF-MODULE. After selecting P00, input to IF1 terminal of TU002 (38.9 MHz Using PM5518) After selecting P00, set to 2.5V + _ 0.2V (Using FRANCE : T101, PAL/SCAM B/G,I,D/K : L102) Samsung Electronics...
Page 45
7. Pattern Generator : PAL color bar. 100% White (100%) White. White (75%) 0.7V Burst 0.3V 0.3V Horizontal sync signal Color bar signal waveform Fig. 5-4 Alignment Tape White Black 100% Color bar pattern Fig. 5-6 Color bar signal of alignment tape (75% Color Bars) Samsung Electronics...
Page 46
STOP1 Stop (Play position 5 Min. over) STOP 2 (MAIN Break ON MODE) FF / REW 1 High speed Rew, Low speed FF FF / REW 2 High speed FF, Low speed Rew X : DON’T CARE 5-10 Samsung Electronics...
Is Q801 Pin 3 Pin 64 Voltage 5V? 19~22V? Check IC801 Check/Replace T801. Check H.V SYNC on IC901 Pins 1, 2 Check/Replace IC901. Check IC901 Pin 3 is High when power is On. Check/Replace IC902. Check the voltage of TU001. Samsung Electronics...
Page 52
Retouch CN102 or Replace CN102 Check IC901 #64 Check IC804 Check IC901 #23, #24 Check another I Check IC801 Bus Line. Check after Bus Replace Line Open Check Q801 Replace Check D801~D805 Check IC901 #28~31 Check/Replace D801~D805 Replace IC901 Samsung Electronics...
Page 53
Check IC901 #23, #24 Check Another I bus line Check After bus line open Check D834 "H" and IC807 Replace Check IC201 #12, #37 Replace Check Q401, Q402 Replace Check IC201 #40, #41, R416, R408, R409, D401, D402 Replace Samsung Electronics...
Page 56
Press Play Button Play Indication in (Regulator Inoperative) Display Mechanism (Mechanism Does Not Operation Operate in Play Mode) Does Not Operate or Operates but Stops Soon Video Missing in PB-Video Play Mode See (PB Audio) Audio Missing in Play Mode Samsung Electronics...
Page 57
OK but VCR Stops Soon Check CYL FG. (SW 25Hz) ICM601-93 ICM601-24 Capstan (Capstan Does Rotation Not Rotate) PTM601, PTM602, S, T Reel Supply/Take Up Reel Sensor ICM601-99,98 PTM601, PTM602 Deck Loading Motor Prog, SW State ICM601-63,64,65 Mechanism Replace ICM601 Samsung Electronics...
Page 58
Load VCR With a Blank Tape and Press Record Button Rew SW Logic Tape Eject Change Tape Replace ICM601 Replace SWM602 D/ REC (H) Check ICM601 ICM601-66 High (Video Missing in REC-Video Record Mode) See (Audio Mising in Record Mode) Samsung Electronics...
Page 59
6-16 Fast Forward Mode Inoperative Load VCR With a Tape and Press F.Fwd Button Mechanism (STOP) (Mechanism Does Not State ICM601-63, Operate In Play Mode) 64,65 (F.FWD) (STOP) Capstan Motor (Capstar Does Rotation Not Rotate) (Rotate) Check Mechanism Samsung Electronics...
Page 60
6-17 Rewind Mode Inoperative See (Fast Forward Mode Load VCR With Inoperative) a Tape (Rotate) Press Rewind Button Mechanism (STOP) (Mechanism Does Not State ICM601-63, Operate In Play Mode) 64,65 (Rew) (STOP) Capstan Motor See ICM601-25 Rotation (Rotate) Check Mechanism 6-10 Samsung Electronics...
Page 61
6-18 Rev Search Mode Inoperative See Play Mode Play Inoperative Operation Press REV Search Button Play Speed Check Mechanism Replace ICM601 Capstan Speed Serach Speed Rew SW Logic Noise Bar Locking Change Tape Replace ICM601 Capstan Motor Replace ICM601 Samsung Electronics 6-11...
Page 62
Turn the VCR Power On and Insert a Tape Check (Control Pulse) Check Start/End Tape Loading ICM601-76,77 Sensor ICM601 Check ICM601 - 37 Press Eject Button LM B+ Line ICM602-10:LOW Replace Check ICM601 ICM603-2 : HIGH ICM602 6-12 Samsung Electronics...
Page 63
Troubleshooting 6-20 No Servo Lock Play C-FG Check Start/End ICM601-93 Sensor ICM601 Check CTL Pluse A/C Head ICM601-4 Check CTL Pulse AC Level (SP, LP : Over 2Vp-p) Replace ICM601 Samsung Electronics 6-13...
Page 64
CNM603-5 Power Supply AL 5V Check 6V at AL6V CNM603-8 Line of Power Supply Place the VCR In Play Mode Check I-LIMIT. CNM603-3 2.5V RM618 2.5V Check C.M CTL/ Check CNM603-4 RM607, RM604 ICM601 Check Capstan Motor 6-14 Samsung Electronics...
Page 65
6-22 Drum Does Not Rotate Check 12V at AL15V Check 12V of Power Supply CNM602-4 Place the VCR In Play Mode Faster Check D-FG CYL-Speed ICM601-97 Square Wave Slower Replace (8 MHz) XTM601, CM609, CM610 XTM601 Check Cylinder Motor Samsung Electronics 6-15...
Page 66
6-23 Video Missing In Play Mode See (Video Missing Video EE Mode In EE Mode) Operation Place VCR Play Mode Check Video FM In Check ICM301-18 Video Head ICM301-17 Video Check ICM301-20 QM302 Video Check Video Out Line ICM301-29 Replace ICM301 6-16 Samsung Electronics...
Page 67
Troubleshooting 6-24 Video Missing In Record Mode Video EE Mode TV Switching Operation Circuit Check Place VCR Record Mode FM-Video Replace ICM301 ICM301-21 FM-Video Check RM313 ICM301-18 Check Video Head Samsung Electronics 6-17...
Page 68
Troubleshooting 6-25 Color Missing In Play Mode FM-ENV See (Video Missing ICM301-61 In Play Mode) Color Check S/W 25Hz ICM301-71 ICM601 ICM301-11 Check XTM302 : 4.43MHz Change XTM302 Replace ICM301 6-18 Samsung Electronics...
Page 69
Troubleshooting 6-26 Color Missing In Record Mode (VIdeo In) TV Switching Record Mode Circuit Check Check Color Replace XTM301 XTM301 : 4.43MHz ICM301-61 Replace ICM301 FM Signal Check CM351 ICM301-71 Replace ICM301 Samsung Electronics 6-19...
Page 70
4 : PB Audio Signal Block (AUDIO HEAD A2 (MUTH) (Small Signal) Check ICM301 Check CM301 pin100 : PB audio signal (Small Signal) Check ICM301 Replace ICM301 pin96 : PB Audio Signal Check CNM101 pin10 Replace CNM001 PB Audio signal 6-20 Samsung Electronics...
2 and 15 (PH high output of micomÕs pin 6), and then to IC201 pin 17, where it outputs as RGB. 9-1-1(D) SYNCHRONOUS RECORDING: The viewer sees the signal from the 1st tuner , while the signal from the second tuner is recorded. Audio processing for the French system type is shown in the table. Samsung Electronics...
Page 84
FRA H FRA H PAL/SEC FRANCE-L FRANCE-L' a C. SYSTEM : PAL/SEC ARE AUTO mode, and France is SECAM mode. 23,24 SDA,SCL Extra control signals are all controlled by the I C bus. Select INT/EXT FRENCH system modulation Samsung Electronics...
Page 85
6.4 ~ 7.2V : In AV-AM Mode, connect pin 7 to B and pin 9 to A. :EXT More than 7.3V : In AV-FM Mode, connect pin 7 to B and pin 9 to C. 53,54 SDA, SCL Port BG/I L AUTO DK/L Samsung Electronics...
Schematic Diagrams 12. Schematic Diagrams PB Y PROCESS BLUE REC Y PROCESS Samsung Electronics 12-1...
Page 92
@ ? h f ? @ @ ? h f ? @ ? @ L ? ? @ @ ? ? @ H ? ? @ L ? @ ? h f ? @ @ @ @ @ @ ? 12-2 Samsung Electronics...
Page 93
? @ @ @ @ ? J @ e @ L 7 @ e @ 1 @ @ H ? N @ L ? REC Y PROCESS BLUE PB Y PROCESS BLUE REC AUDIO REC C PROCESS PB AUDIO PB C PROCESS Samsung Electronics 12-3...
Page 96
@ ? e ? @ f @ ? e ? @ f @ ? e ? @ f @ ? e ? @ f @ ? e ? @ f @ ? e ? @ f @ ? e ? @ f @ ? e ? @ f @ ? e ? @ f @ ? e ? @ f @ ? e ? @ f @ ? e ? @ f @ POWER LINE BLUE SIGNAL LINE 12-6 Samsung Electronics...
Page 97
Schematic Diagrams 12-7 TV (3/4) POWER LINE BLUE SIGNAL LINE Samsung Electronics 12-7...
Page 100
Schematic Diagrams 12-13 CONTROL 12-12 TTX 12-14 MASTER 12-15 FRONT-A/V POWER LINE BLUE SIGNAL LINE 12-10 Samsung Electronics...
Page 101
Schematic Diagrams 12-16 Voltages (VTR) ICM301 ICM601 ICM901 ICM602 PLAY STOP PLAY STOP PLAY STOP PLAY STOP PLAY STOP PLAY STOP PLAY REC STOP PLAY REC STOP Samsung Electronics 12-11...
Page 102
61~62 RESET 63~64 IC301 TDA8356 IC601 TDA7267 Units : Volts Units : Volts PIN NO PIN NAME VOL T AGES(V ) PIN NO PIN NAME VOL T AGES(V ) VD-INPUT VD+INPUT 16.9 OUTPUT 41.5 S-GND 9~16 P-GND 12-12 Samsung Electronics...
Need help?
Do you have a question about the TW14C52S/BWT and is the answer not in the manual?
Questions and answers