Television Video Cassette Recorder Chassis : C17A (TS-10 ) Model : TX14N3DF4X/XET TX21B4DF4X/XET TF14P64X/XEF TX14N34X/XET TI14N34X/XEU TI14N54X/XEU TI14P1DF4X/XEU TI14P74X/XEU TI14P94X/XEU TI20P1DF4X/XEU TI20P5DF4X/XEU Television Video Cassette Recorder CONTENTS Precautions Specifications Disassembly and Reassembly Alignment and Adjustment Troubleshooting Exploded View and Parts List...
The current measured should the X–ray Protection Specifications Label, and not exceed 0.5 milliamp. Reverse the power- the Product Safety and X-ray Warning Note on plug prongs in the AC outlet and repeat the the service data schematic. test. Samsung Electronics...
Page 4
14. Components, parts and wiring that appear to have overheated or that are otherwise damaged should be replaced with parts that meet the original specifications. Always determine the cause of damage or overheat- ing, and correct any potential hazards. Samsung Electronics...
Page 5
Make sure that the portion around the serviced part has not been damaged. 8. Always connect a test instrument’s ground lead to the instrument chassis ground before connecting the positive lead; always remove the instrument’s ground lead last. Samsung Electronics...
Page 6
4. Do not use freon-propelled chemicals. These unpackaged replacement ESDs. Motions such can generate electrical charges that damage as brushing clothes together, or lifting a foot ESDs. from a carpeted floor can generate enough static electricity to damage an ESD. Samsung Electronics...
20” (486 x 473 x 485) 21” (520 x 495 x 508) Weight 14” (11.1 kg) 15” (14.8 kg) 20” (19 kg) 21” (23.4 kg) Operating temperature 5°C - 40°C (41°F - 104°F) Relative humidity 10% - 75% Samsung Electronics...
3-1-1 Top View Œ ´ ˇ ¨ ˆ Ø Fig. 3-1 Top parts Location-1 Œ GEAR FL CAM ´ MOTOR LOADING ASS’Y ˇ LEVER FL ARM ASS’Y ¨ HOLDER FL CASSETTE ASS’Y ˆ LEVER FL DOOR Ø SLIDER FL DRIVE Samsung Electronics...
Page 10
´ CYLINDER ASS’Y ˝ GEAR IDLE ˇ ACE HEAD ASS’Y Ô LEVER IDLE ¨ LEVER UNIT PINCH ASS’Y LEVER T BRAKE ASS’Y ˆ LEVER #9 GUIDE ASS’Y Ò DISK T REEL Ø LEVER TENSION ASS’Y ∏ BAND BRAKE ASS’Y Samsung Electronics...
Page 11
Œ GEAR JOINT 1 ´ GEAR JOINT 2 ˇ BRACKET GEAR ¨ MOTOR CAPSTAN ASS’Y ˆ LEVER T LOAD ASS’Y Ø GEAR LOADING DRIVE ∏ LEVER S LOAD ASS’Y ” HOLDER CLUTCH ASS’Y ’ BELT PULLEY ˝ SLIDER CAM Samsung Electronics...
Page 12
Lever FL Cassette-R ´ at disassembling and "B" reassembling. ´ LEVER FL DOOR ˇ HOOK "C" Fig. 3-4 Lever FL Door Removal RAIL [B] Œ HOLDER FL CASSETTEE ASS`Y ´ LEVER FL CASSETTEE -R "A" BOSS [A] Fig. 3-5 Holder FL Cassette Ass’y Removal Samsung Electronics...
Page 16
LEVER LOAD T LEVER LOAD S Lever Tension Drive Removal TIMING POINT 2 TIMING POINT 3 PIN A PIN C PIN D PIN B ˇ SLIDER CAM Fig. 3-14 Gear Loading Drive, Slider Cam, Lever Load S, T Ass’y Assembly Samsung Electronics...
Page 17
ˇ SPRING BRAKE Œ SPRING TENTION LEVER STOPPER Œ LEVER S BRAKE ASS`Y HOOK(C) "A" MARK[B] HOOK(B) ´ LEVER T BRAKE ASS`Y Fig. 3-16 Lever Tension Ass’y, Band Brake Ass’y Removal Fig. 3-17 Lever Brake S, T Ass’y Removal Samsung Electronics...
Page 18
´ DISK T REEL add oil in the boss of Lever Idle Œ. "A" Œ LEVER IDLE ´ GEAR IDLE "B" ´ GEAR IDLE HOOK "C" Fig. 3-19 Disk S, T Reel Removal Fig. 3-18 Gear Idle Ass’y Removal Samsung Electronics 3-10...
Page 19
Fig. 3-21 Lever Up Down Ass’y Removal DETAIL B SPRING GEAR CENTER ASS'Y GUIDE LEVER UP DOWN ASS'Y RING GEAR <GOOD> <BAD> POST HOOK Fig. 3-20 Holder Clutch Ass’y Removal MAIN BASE Fig. 3-22 Lever Up Down Ass’y Removal 3-11 Samsung Electronics...
Page 20
Œ GUIDE CASSETTE DOOR Œ LEVER UNIT PINCH ASS`Y HOOK [A] ´ PLATE JOINT ˇ SPRING PINCH DRIVE Fig. 3-23 Guide Cassette Door Removal Fig. 3-24 Lever Unit Pinch Ass’y, Plate Joint, Spring Pinch Drive Removal Samsung Electronics 3-12...
Page 21
2) After reinstalling, check the bottom side of the Post #9 Guide to the top side of Main Base. "A" Œ SPRING #9 GUIDE ´ LEVER #9 GUIDE ASS`Y "B" Fig. 3-26 FE Head Removal Fig. 3-25 Lever #9 Guide Ass’y Removal 3-13 Samsung Electronics...
Page 22
2) Remove the screw Œ. 3) Lift the ACE Head Ass’y ´. Œ SLIDER S ASS`Y Œ SCREW ´ SLIDER T ASS`Y ´ HEAD ACE ASS`Y Fig. 3-28 Slider S, T Ass’y Removal Fig. 3-27 ACE Head Removal Samsung Electronics 3-14...
Page 23
1) Release the Hook Œ. 2) Lift the Lever Head Cleaner Ass’y ´. ´ LEVER HEAD CLEANER ASS'Y Œ HOOK SLEEVE-HEAD CLEANER ˇ CYLINDER ASS'Y Fig. 3-29 Plate Ground Deck, Cylinder Ass’y Removal Fig. 3-31 Level Head Cleaner Ass’y Removal 3-15 Samsung Electronics...
Page 24
3) Rotate Gear Worm Œ clockwise using screw driver again up to the state of eject mode and then pick out the tape.(Refer to Fig.3-33) ˇ MOTOR CAPSTAN ASS'Y Fig. 3-32 Damper Capstan,Motor Capstan Ass’y Removal FRAME Fig. 3-34 Samsung Electronics 3-16...
Page 25
∆ CAPSTAN MOTOR PULLEY BELT PULLEY ∆ HOLDER CLUTCH ASS’Y GEAR CENTER ASS’Y GEAR IDLE (2Point) LOADING MOTOR BAND BRAKE ASS’Y BRAKE T ASS’Y ∆ : Cleaning O : Check and replacement in necessary : Add Oil 3-17 Samsung Electronics...
Page 26
Fig. 3-4-1 Location of Tape Transport Adjustment PINCH ROLLER FE HEAD CYLINDER ASS'Y GUIDE ROLLER "S" GUIDE ROLLER "T" POST TENSION #8 GUIDE POST #9 GUIDE POST #3 GUIDE POST MAIN BASE ACE HEAD CAPSTAN SHAFT Fig. 3-4-2 Tape Travel Diagram Samsung Electronics 3-18...
Page 27
Fig. 3-5-1 Location of ACE Head Adjustment Screw 4-5-1(d) ACE HEAD POSITION (X-POINT) ADJUSTMENT 1) See “2. Alignment and Adjustment” for ACE Head AUDIO HEAD position (X-Point) adjustment. VIDEO HEAD 0 ~ 0 .25 mm CONTROL HEAD Fig. 3-5-2 ACE Head Height Adjustment 3-19 Samsung Electronics...
Page 28
) driver to obtain a flat video RF envelope as shown in Fig. 3-8. IDEAL ENVELOPE S HEIGHT TOO HIGH S HEIGHT TOO LOW T HEIGHT TOO HIGH T HEIGHT TOO LOW GUIDE ROLLER S GUIDE ROLLER T Fig. 3-5-6 Guide Roller S, T Height Adjustment Samsung Electronics 3-20...
Page 29
3) Brake is operated by slider cam at FF/REW mode. 4) Transportation of accurate driving force is done by gears. (Gear Center Ass’y) Note : If the spec. does not meet the followings speci- fications, replace the holder clutch ass’y and then recheck. 3-21 Samsung Electronics...
Adjustment, Option and Reset. 3. Access the Adjustment Mode by pressing the “VOLUME” keys ( Up or Down). The adjust- ment parameters are listed in the accompany- ing table, and selected by pressing the CHAN- NEL keys (L,M). Samsung Electronics...
Page 32
"FACTORY" key . Even if the TV power is cut off, the Aging Mode is not cancelled. The "AGING" marking is displayed on the screen. The AGINGmode is cancelled by repressing the "FACTORY" key. Samsung Electronics...
Page 33
2HD/2HDLP/4HD/HIFI G-CODE SHOWVIEW/VIDEO PLUS/NONE ATS OPTION ON/OFF VPS/PDC PDC/VPS/NONE ON/OFF 4-3 Reset BYTE ITEM Contrast Bright Sharpness Color Tint Volume Program Number Color System Sound System 3DB LNA Panel Lock Language Clock Timer On Time Sleep PICTURE MODE Samsung Electronics...
Page 34
2. Turn on the TV. Set the Brightness and Contrast controls to minimum (zero beam current). 3. The high voltage should not exceed 27.5KV. 4. Adjust the Brightness and contrast controls to both extremes. Ensure that the high voltage does not exceed 27.5KV under any conditions. Samsung Electronics...
Page 35
9. Slowly move the deflection yoke forward, and adjust for the best overall green screen. 10. Temporarily tighten the deflection yoke. 11. Produce blue and red rasters by adjusting the low-light controls. Check for good purity in each field. 12. Tighten the deflection yoke. Samsung Electronics...
Page 36
1. Input either a Lion Head or a “pure white” pattern. 2. Warm up the TV for 30 minutes. 3. Check the data in the Service Mode 4. Adjust RG, BG in the Factory Mode. 4-4-7 (B) LOW-LIGHT ADJUSTMENT 1. Automatically accomplished during the high-light adjustment. Samsung Electronics...
Page 37
2. DC VOLTMETER 1. Connect DC Voltmeter to AFT terminal of TUNER IF-MODULE. 2. After selecting P00, input to IF1 terminal of TU002(38.9 MHz Using PM5518) 3. After selecting P00, set to 2.5V±0.2V(Using FRANCE : T101, PAL/SCAM B/G,I,D/K : L102) Samsung Electronics...
Page 38
7. Pattern Generator : PAL color bar. 100% White (100%) White. White (75%) 0.7V Burst 0.3V 0.3V Horizontal sync signal Color bar signal waveform Fig. 4-4 Alignment Tape White Black 100% Color bar pattern Fig. 4-6 Color bar signal of alignment tape (75% Color Bars) Samsung Electronics...
Page 39
Play, Rec,F-PS,Still,SLOW,F-ADV STOP1 Stop (Play position 5 Min. over) STOP 2 (MAIN Break ON MODE) FF / REW 1 High speed Rew, Low speed FF FF / REW 2 High speed FF, Low speed Rew X : DON’T CARE Samsung Electronics...
Pin 54 Voltage 3.3V? 19~22V? Check IC801S /Zener diode Check/Replace Check T801S H.V SYNC on IC201S Pins 33, 21, 22 Check/Replace IC901. Check IC201S Pin 11 is High when power is On. Check/Replace IC902. Check the voltage of TU001. Samsung Electronics...
Page 42
5-2 No RF Picture / Sound Check IC201S #40, #24 Check Another I bus line Check After Check bus line open IC201S R, G, B, pins 51, 52, 53 Replace IC201S Check Q401, Q402 Replace Check FBT Replace Samsung Electronics...
Page 45
Press Play Button Play Indication in (Regulator Inoperative) Display Mechanism (Mechanism Does Not Operation Operate in Play Mode) Does Not Operate or Operates but Stops Soon Video Missing in PB-Video Play Mode See (PB Audio) Audio Missing in Play Mode Samsung Electronics...
Page 46
OK but VCR Stops Soon Check CYL FG. (SW 25Hz) ICM601-93 ICM601-24 Capstan (Capstan Does Rotation Not Rotate) PTM601, PTM602, S, T Reel Supply/Take Up Reel Sensor ICM601-99,98 PTM601, PTM602 Deck Loading Motor Prog, SW State ICM601-63,64,65 Mechanism Replace ICM601 Samsung Electronics...
Page 47
Load VCR With a Blank Tape and Press Record Button Rec SW Logic Tape Eject Change Tape Replace ICM601 Replace SWM611 D/ REC (H) Check ICM601 ICM601-66 High (Video Missing in REC-Video Record Mode) See (Audio Mising in Record Mode) Samsung Electronics...
Page 48
5-13 Fast Forward Mode Inoperative Load VCR With a Tape and Press F.Fwd Button Mechanism (STOP) (Mechanism Does Not State ICM601-63, Operate In Play Mode) 64,65 (F.FWD) (STOP) Capstan Motor (Capstan Does Rotation Not Rotate) (Rotate) Check Mechanism Samsung Electronics...
Page 49
5-14 Rewind Mode Inoperative See (Fast Forward Mode Load VCR With Inoperative) a Tape (Rotate) Press Rewind Button Mechanism (STOP) (Mechanism Does Not State ICM601-63, Operate In Play Mode) 64,65 (Rew) (STOP) Capstan Motor See ICM601-25 Rotation (Rotate) Check Mechanism Samsung Electronics...
Page 50
5-15 Rev Search Mode Inoperative See Play Mode Play Inoperative Operation Press REV Search Button Play Speed Check Mechanism Replace ICM601 Capstan Speed Serach Speed Rec SW Logic Noise Bar Locking Change Tape Replace ICM601 Capstan Motor Replace ICM601 5-10 Samsung Electronics...
Page 51
5-16 Cassette Loading Mechanism Does Not Operate Turn the VCR Power On and Insert a Tape Check (Control Pulse) Check Start/End Tape Loading ICM601-76,77 Sensor ICM601 Check ICM601 - 39 Press Eject Button LM B+ Line ICM602-12:LOW Replace Check ICM601 ICM602-11:HIGH ICM602 Samsung Electronics 5-11...
Page 52
Troubleshooting 5-17 No Servo Lock Play C-FG Check Start/End ICM601-93 Sensor ICM601 Check CTL Pluse A/C Head ICM601-4 Check CTL Pulse AC Level (SP, LP : Over 2Vp-p) Replace ICM601 5-12 Samsung Electronics...
Page 53
CNM603-5 Power Supply AL 5V Check A5V at AL6V Line of Power Supply CNM603-8 Place the VCR In Play Mode Check I-LIMIT. CNM603-3 2.5V RM618 2.5V Check C.M CTL/ Check CNM603-4 RM606, RM604 ICM601 Check Capstan Motor Samsung Electronics 5-13...
Page 54
Troubleshooting 5-19 Drum Does Not Rotate Check 12V Check 12V ICM602-9,21 Place the VCR In Play Mode Faster Check D-FG,D-PG CYL-Speed ICM601-96,97Square Wave Slower Replace (8 MHz) XTM601, CM609, CM610 XTM601 Check Cylinder Motor 5-14 Samsung Electronics...
Page 55
5-20 Video Missing In Play Mode See (Video Missing Video EE Mode In EE Mode) Operation Place VCR Play Mode Check Video FM In Check ICM301-18 Video Head ICM301-17 Video Check ICM301-20 QM302 Video Check Video Out Line ICM301-29 Replace ICM301 Samsung Electronics 5-15...
Page 56
Troubleshooting 5-21 Video Missing In Record Mode Video EE Mode TV Switching Operation Circuit Check Place VCR Record Mode FM-Video Replace ICM301 ICM301-21 FM-Video Check RM313 ICM301-18 Check Video Head 5-16 Samsung Electronics...
Page 57
Troubleshooting 5-22 Color Missing In Play Mode FM-ENV See (Video Missing ICM301-61 In Play Mode) Color S/W 25Hz Check ICM301-71 ICM601 ICM301-11 Check XTM301 : 4.43MHz Change XTM301 Replace ICM301 Samsung Electronics 5-17...
Page 58
Troubleshooting 5-23 Color Missing In Record Mode (VIdeo In) TV Switching Record Mode Circuit Check Check Color Replace XTM301 XTM301 : 4.43MHz ICM301-61 Replace ICM301 FM Signal Check CM351 ICM301-71 Replace ICM301 5-18 Samsung Electronics...
Page 59
1 : PB Audio Signal Block (AUDIO HEAD AZIMUTH) (Small Signal) Check ICM301 Check CM301 pin100 : PB audio signal (Small Signal) Check ICM301 Replace ICM301 pin96 : PB Audio Signal Check TV NICAM PART(Sound Block) Samsung Electronics 5-19...
Page 60
Check PC 5V Line ICM301 pin 75: Check Replace ICM301 ICM301 pin7 REC audio signal Check Check CM370, RM357, RM358 FLM501 Pin5 REC CM371, CM373, CM372, bias signal QM312, RM359 Check Check A/C CNM302 , Pin5 Head Assembly Replace CNM302 5-20 Samsung Electronics...
IC201S pin 42, where it outputs as RGB. 8-1-4 SYNCHRONOUS RECORDING: The viewer sees the signal from the 1st tuner , while the signal from the second tuner is recorded. Audio processing for the French system type is shown in the table. Samsung Electronics...