Table of Contents
Advertisement
Quick Links
Installation
Flowswitch Kit for RTX5000 &
RTX5500 Texture Sprayers
For installation of Retro Flowswitch kits. For professional use only.
Kit Part Number: 17Z245
Important Safety Instructions
Read all warnings and instructions in this manual and in the Operation and
Parts manual (3A3265) before using the equipment. Save all instructions.
Related Manuals
3A3265
Operation, Parts
3A7027A
ti27921a
EN
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Graco RTX5500
Summary of Contents for Graco RTX5500
- Page 1 Installation 3A7027A Flowswitch Kit for RTX5000 & RTX5500 Texture Sprayers For installation of Retro Flowswitch kits. For professional use only. Kit Part Number: 17Z245 Important Safety Instructions Read all warnings and instructions in this manual and in the Operation and Parts manual (3A3265) before using the equipment.
- Page 2 Warnings Warnings The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclamation point symbol alerts you to a general warning and the hazard symbols refer to procedure-specific risks. When these symbols appear in the body of this manual or on warning labels, refer back to these Warnings.
-
Page 3: Fire And Explosion Hazard
Do not kink or over-bend the hose. • Do not expose the hose to temperatures or to pressures in excess of those specified by Graco. • Do not use the hose as a strength member to pull or lift the equipment. -
Page 4: Personal Protective Equipment
Warnings WARNING PRESSURIZED EQUIPMENT HAZARD Fluid from the equipment, leaks, or ruptured components can splash in the eyes or on skin and cause serious injury. • Follow the Pressure Relief Procedure when you stop spraying/dispensing and before cleaning, checking, or servicing equipment. •... -
Page 5: Pressure Relief Procedure
Preparation Preparation Pressure Relief Procedure Unplug sprayer. Turn fluid regulator all the way down. Follow the Pressure Relief Aim gun into hopper or waste bucket and Procedure whenever you see this trigger the gun until all air and material symbol. pressure is relieved. -
Page 6: Installation
Preparation Installation Perform Pressure Relief Procedure. Fasten the new flowswitch assembly to the unit using the provided bolts as Unplug unit and ensure the power switch shown below. Torque each bolt to 27-32 is set to off. in-lb (31.-3.6 N•m). Remove the hopper, front shroud, and rear shroud. -
Page 7: Wiring Diagram
Wiring Diagram Wiring Diagram NOTE: Use for flowswitch assembly wiring reference only. Other components will vary based on sprayer model. 3A7027A... -
Page 8: Air Flow Diagram
Air Flow Diagram Air Flow Diagram 3A7027A... - Page 9 Notes Notes 3A7027A...
-
Page 10: California Proposition
Compliance Compliance California Proposition 65 WARNING: This product can expose you to chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov. 3A7027A... -
Page 11: Graco Standard Warranty
Graco’s written recommendations. This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of non-Graco component parts. -
Page 12: Graco Information
For the latest information about Graco products, visit www.graco.com. For patent information, see www.graco.com/patents. TO PLACE AN ORDER, contact your Graco distributor or call 1-800-690-2894 to identify the nearest distributor. All written and visual data contained in this document reflects the latest product information available at the time of publication.
Need help?
Do you have a question about the RTX5500 and is the answer not in the manual?
Questions and answers