Preparation; Unpacking The Tv - JVC LT-49C888 Instruction Manual

Chapter
2

Preparation

2
Thank you
Your new TV has many features and incorporates the latest technology to enhance your viewing
experience. We recommend that you spend some time reading this instruction manual so that you fully
understand these features. You will also find some hints and tips to help you resolve any issues.
Read all the safety instructions carefully before use and keep this instruction manual for future reference.

Unpacking the TV

Remove all packaging from the TV. Retain the packaging. If you dispose of it please do so according to local regulations.
The following items are included:
TV Stand Neck Cover and
Neck
GB
Instruction Manual
49" LED Smart 4K HDR TV
LT-49C888
Instruction Manual
JVC 49' LED Smart 4K HDR TV LT-49C888 Manual.indd 7
for purchasing your new JVC TV.
A
Screws x5
TV Stand Base
Quick Start Guide
49" LED Smart 4K HDR TV
LT-49C888
Thank you
for purchasing your new JVC TV.
Your new TV incorporates the latest technology to enhance your viewing
experience. We would suggest that you allow about 20 mins for initial setup.
Please follow this guide for a successful first time installation.
The latest eco-friendly power-saving technology will switch off the TV if
it is left on and idle for 4 hours. Please refer to "Auto Standby" under the
"Time Settings" section of the instruction manual for more detail.
1
Unpacking
Remove all packaging from the unit. Retain the packaging. If you dispose of it please do so according to any local regulations.
TV TV Stand Base Screws (B) x 6
TV Stand Neck Remote Control/ Instruction Manual
AAA Batteries x2
TV Stand Neck cover Quick Start Guide
Screws (A) x 5
Please inspect your TV for damage after unpacking. If you do notice any damage please consult your dealer.
2 Operating Your Remote Control
1. Slide open the battery compartment on the back of the remote control.
2. Insert two AAA size batteries. Make sure to match the (+) and ( - )
ends of the batteries with the (+) and ( - ) ends indicated in the battery
compartment.
3. Slide the battery compartment cover back into place. Make sure it clicks
into place.
JVC 49' LED Smart 4K HDR TV LT-49C888 Quick Start.indd 1
Quick Start Guide
2
.,/@ ABC
4 5
GHI JKL
7 8
PQRS TUV
0
TV
B
V
OK
LANG. SUBT.
Screws x6
Remote Control /
AAA Batteries x 2
3 Installing the Base Stand
Fitting the Neck and Neck
Cover Together
1. Fit the neck cover over the neck. A
2. Using 2 of the supplied screws (A), A
screw the neck and neck cover
together.
Protective
Bag
B
Fitting the Neck and Stand to the TV
3. Ensure the TV is switched off and not connected to
the mains power supply.
4. Lay the TV down on a flat surface ideally on the
edge of a table so the base of the TV slightly
overhangs the edge of the table, with the back side
facing up. Please make sure a soft cushioned
material (such as a dry bath towel or thick piece of
foam) is placed beneath the screen. You can leave
the protective bag on to protect the TV at this point.
5. Slide the Neck and Neck cover under the lip, the
neck will fit snugly over the screw holes. Then screw
the Neck to the TV using the 6 screws (B) supplied.
6. Once the Neck is secure screw the base to the neck
A
using the 3 screws (A) supplied. Be careful not the Table Cushioned
drop the base, its heavy. material
The LCD display is very fragile, and must be protected at all times when installing and removing the base stand. Be sure that no hard or sharp object,
or anything that could scratch or damage the LCD display, comes into contact with it. DO NOT exert pressure on the front of the TV at any time because
the screen could crack.
4 Connecting the Aerial and Turning on the TV
1. Connect one end of the RF coaxial cable
Optional
to the aerial socket on the wall and the
other end of the cable to the ANT socket If you want to connect to the internet via a wired connection then
on the back of your TV. connect your ethernet cable to the LAN socket.
2. Plug the TV into a mains socket and
switch on at the mains.
3. In standby mode, press the
button on
the remote control to turn the TV on. The
LED indicator will flash for a few seconds
then the TV will switch on.
RF coaxial cable
(not included)
• Do not connect the TV to the mains supply until you have completed all the connections.
• Always disconnect the TV from the mains socket when not in use for a long period of time.
• The button on the remote control is only used for switching the TV into standby, it does not disconnect the TV from the mains power.
To completely disconnect the mains power, please remove the mains plug from the mains socket.
20/02/2018 12:58
3
DEF
6
MNO
9
WXYZ
P
EPG
TXT
7
22/02/2018 09:41