Related Manuals for aFe Power 50-70077D
Summary of Contents for aFe Power 50-70077D
- Page 1 Momentum GT Cold Air Intake System Instruction Manual P/N: 50-70077D / 50-70077R _____________________________ Make: Nissan Model: Frontier Year: 2020-2021 Engine: V6-3.8L...
- Page 2 • Please read the entire instruction manual before proceeding. • Ensure all components listed are present. • If you are missing any of the components, call customer support at 951-493-7185. • Ensure you have all necessary tools before proceeding. • Do not attempt to work on your vehicle when the engine is hot. •...
- Page 3 A1/A2 Page 3...
- Page 4 REMOVAL REMOVAL Figure A Refer to Figure A for Steps 1-2 Step 1: Disconnect the mass air flow (MAF) sensor. Step 2: Using a 10mm nut driver, remove the bolt securing the factory intake airbox to the vehicle. Keep the bolt for later use.
- Page 5 REMOVAL Figure B Refer to Figure B for Steps 3-5 Step 3: Remove the engine cover. Step 4: Loosen the two 10mm bolts mounting the factory intake tube to the engine. Step 5: Using an 8mm nut driver, loosen the clamp at the throttle body. Page 5...
- Page 6 REMOVAL Figure C Refer to Figure C for Steps 6-7 Step 6: Disconnect the crankcase vent (CCV) line from the engine. Step 7: Remove the factory air intake. Carefully, pull the factory intake tube away from the throttle body and pull up on the factory airbox.
- Page 7 Refer to Figure D for Steps 8-9 Step 8: Transfer the two (2) bottom factory grommets from the factory airbox to the aFe POWER housing. Step 9: Transfer the remaining grommet and metal sleeve from the backside of the factory airbox to the aFe POWER housing.
- Page 8 Warmer air affects the performance of the vehicle. With the plug installed, the aFe POWER intake will prevent hot air from entering the engine bay, making sure the coolest air available is directed into the engine. It will also reduce the noise of the intake.
- Page 9 Step 11: Press the aFe POWER housing into the vehicle and onto the two (2) mounting pegs. Step 12: Install the bolt from Step 2 on the inside of the aFe POWER housing. Tighten the bolt. Step 13: Place the largest supplied clamp over the flange of the aFe POWER housing. Do not tighten the clamp.
- Page 10 INSTALL Figure G Refer to Figure G for Step 14 Step 14: Install the supplied coupling and clamps onto the throttle body. Tighten the clamp at the throttle body, but do not tighten the clamp at the open end of the coupling. Page 10...
- Page 11 INSTALL Figure H Refer to Figure H for Step 15 Step 15: Install the supplied hose and one (1) supplied spring clamp onto the engine’s CCV opening. Page 11...
- Page 12 Figure I Refer to Figure I for Steps 16-17 Step 16: Transfer the MAF sensor from the factory intake airbox to the aFe POWER intake tube, and secure it using the supplied M4 screws. Step 17: Install the supplied air filter onto the aFe POWER intake tube. Tighten the clamp.
- Page 13 Step 18: Install the pre-assembled aFe POWER intake tube and air filter into the aFe POWER housing then into the coupling. Step 19: Adjust the aFe POWER intake tube between the coupling and the air filter, then tighten the clamps at both ends, on the throttle body side and on the aFe POWER housing side.
- Page 14 Step 21: Connect the MAF sensor to the harness. Step 22: Re-install the engine cover. Step 23: Make sure all components and connections are secure. Your installation is now complete. Thank you for choosing aFe POWER! NOTE: Check all bolts, clamps, and connectors after 100-200 miles. Page 14...
- Page 15 Page left blank intentionally. Page 15...
- Page 16 252 Granite Street Corona, CA 92879 https://afepower.com/contact 11/3/2021 JTP...
Need help?
Do you have a question about the 50-70077D and is the answer not in the manual?
Questions and answers