Related Manuals for aFe Power F-150
Summary of Contents for aFe Power F-150
- Page 1 FLOW engineering Instruction Manual P/N: 51-22642-B / 54-22642-B Make: Ford Model: F-150 Year: 2015-2021 Engine: V6-2.7L (tt) EcoBoost Make: Ford Model: F-150 Year: 2015-2016 Engine: V6-3.5L (tt) EcoBoost...
- Page 2 • Please read the entire instruction manual before proceeding. • Ensure all components listed are present. • If you are missing any of the components, call customer support at 951-493-7185. • Ensure you have all necessary tools before proceeding. • Do not attempt to work on your vehicle when the engine is hot. NOTE: Retain factory parts for future use.
- Page 3 A1/A2 aFepower.com Page 3...
- Page 4 REMOVAL Figure A Refer to Figure A for Steps 1-4. Step 1: Disconnect the Temperature sensor plug from stock tube. 1 Step 2: Loosen the OE intake clamps using an 8mm nut driver from the left and right side runners. 2 Step 3: Unclamp the top portion of the OE airbox.
- Page 5 INSTALL Figure B Refer to Figure B for Step 5. Step 5: Install trim seal onto the air filter housing. Page 5 aFepower.com...
- Page 6 INSTALL Figure C Refer to Figure C for Steps 6-9. Step 6: Remove the sensor from the OE intake ¼ turn counter clockwise. Step 7: Install the sensor into the rear aFe intake tube. Step 8: Install housing and retain with the factory clips. Step 9: Install filters from inside the housing.
- Page 7 INSTALL Figure D Refer to Figure D for Steps 10-12. Step 10: Install the small 5/8 x 3" hose on the crossover tube with the appropriate clamps, but do not tighten. Step 11: Fit tubes into the remaining couplers. Adjust for best fit and tighten all clamps. Step 12: Connect sensor harness to the Temp Sensor.
- Page 8 INSTALL Vent insert installation: Figure E Refer to Figure E for Step 13. ( For V6-3.5L (tt) only, not necessary on V6-2.7L (tt) ) NOTE: (These procedures should be done with the inlet tubes installed on the engine. It is shown off the vehicle for better illustration.) Step 13: Locate the o.e.
- Page 9 INSTALL Figure F Refer to Figure F for Step 14. ( For V6-3.5L (tt) only, not necessary on V6-2.7L (tt) ) Step 14: Locate the valve cover vent tube that feeds into driver’s side turbo inlet. It is not necessary to remove the engine cover. Page 9 aFepower.com...
- Page 10 INSTALL Figure G Refer to Figure G for Step 15. ( For V6-3.5L (tt) only, not necessary on V6-2.7L (tt) ) Step 15: Note the release clip on the vent tube connectors. Apply pressure against the exposed tail and pull vent fitting off of the turbo inlet tube. It is not necessary to disconnect at the valve cover end.
- Page 11 INSTALL Figure H Refer to Figure H for Step 16. ( For V6-3.5L (tt) only, not necessary on V6-2.7L (tt) ) Step 16: Insert vent fitting with slash cut facing turbo inlet. It should not be a loose fit. It is direction dependent and must not rotate once installed.
- Page 12 INSTALL Figure I Refer to Figure I for Steps 17-18. ( For V6-3.5L (tt) only, not necessary on V6-2.7L (tt) ) Step 17: Reconnect the vent fitting. It will snap over without having to release the plastic clip. Pull up slightly to confirm installation.
- Page 13 INSTALL Figure J Refer to Figure J for Step 19. Step 19: Make sure all clamps and screws are tight. Your installation is now complete. NOTE: Check all bolts, clamps, and connectors after 100-200 miles. Page 13 aFepower.com...
- Page 14 PAGE LEFT BLANK INTENTIONALLY Page 14...
- Page 15 PAGE LEFT BLANK INTENTIONALLY aFepower.com Page 15...
- Page 16 advanced FLOW engineering, inc. 252 Granite Street Corona, CA 92879 TEL: 951.493.7100 • TECH: 951.493.7134 E-Mail:Tech@aFepower.com P/N: 06-81072...
Need help?
Do you have a question about the F-150 and is the answer not in the manual?
Questions and answers