Owner’s Manual Contents Model Identification ......2 Precautions to avoid possible exposure to excessive microwave energy ..... Important safety instructions ......3 Grounding Instructions ...... 5 Installation ......... 6 Display and Features ......7 ommercial icrowave Using the Oven Control (Electronic Models) ......
Model Identification When contacting ACP, provide product information. Product information is located on oven serial plate which is located on the back side of the oven. Record the following information: Warranty service must be performed by an authorized ACP servicer. ACP also recommends contacting an...
IMPORTANT SAFETY INSTRUCTIONS This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death. WARNING When using electrical equipment, basic safety precautions should be followed to reduce the risk of burns, electrical shock, fire, or injury to persons.
Page 4
IMPORTANT SAFETY INSTRUCTIONS WARNING WARNING Liquids such as water, coffee, or tea are able to To avoid risk of fire in the oven cavity: be overheated beyond the boiling point without appearing to be boiling due to surface tension of the a.
Grounding Instructions Earthing Instructions WARNING Oven MUST be earthed. Earthing reduces risk of electric shock by providing an escape wire for the To avoid risk of electrical shock or death, this oven electric current, if an electrical short occurs. This oven is must be grounded.
Installation Unpacking Oven WARNING • Inspect oven for damage such as dents in door or inside oven cavity. Excessive Weight Hazard • Report any dents or breakage to source of purchase Use two or more people to move and install oven. immediately.
Display and Features (some models) Single Key Programming (example of key 1 shown) This feature enables each numbered key to be programmed for a specific START Key cooking procedure/use. To use this feature, simply program the key to the The START key is used to desired length of time and power level.
Page 8
Display and Features (some models) Cooking Display DISPLAYS DESCRIPTION READY displays when oven control will accept READY entries. 00:00 Displays cooking time. If stage cooking is programmed, total cooking time is displayed. Display HOLD These settings display the current power level used Some items in the display can be DEFR for the microwave.
Using the Oven Control (Electronic Control) Manual Time Entry To cook food using a specific entered time and power level. Interrupting Open oven door and place food in oven. Close door. Operation • READY displays. Fan and light will turn on. Open oven door or press STOP/ Press TIME ENTRY key.
Programming the Oven Control (Electronic Control) The display shows Programming Keys PROGRAM Oven is shipped from the factory for single key programming. To change the oven default to allow double key programming, see User Option When set to single key or section.
User Options (Electronic Control) Changing user options Didn’t like an option? Options such as single or double key programming, beep volume, and maximum cooking time can be changed to suit individual preferences. Factory settings are marked in bold. To change options: To change the oven back to the factory setting, simply select the 1.
Digital Dial Operation STYLE 1 Digital Dial option is available on some models only. The switching operation of this Oven Wall Clearances microwave oven can cause voltage A—Allow at least 2” (5.1 cm) of clearance fluctuations on the supply line. around top of oven.
Digital Dial Operation STYLE 2 Digital Dial option is available on some models only. Oven Wall Clearances A—Allow at least 2” (5.1 cm) of clearance around top of oven. Proper air flow around oven cools electrical Oven Wall Clearances components. With restricted air flow, oven may not A—For North American (UL/CSA) models, allow operate properly and life of electrical parts is reduced.
Dial Operation STYLE 3 Dial option is available on some 50 Hz models only. The switching operation of this microwave oven can cause voltage Oven Wall Clearances fluctuations on the supply line. A—For all international models (50 Hz), allow at least 7” (18 The operation of this oven under cm) of clearance around the top of the oven.
Care and Cleaning PART CARE AND CLEANING RECOMMENDATION Clean microwave oven with mild detergent in warm water using soft sponge or cloth. Wring sponge or cloth to remove excess water before wiping equipment. If desired, boil a cup of water in microwave oven to loosen soil before cleaning. Important: Interior, Exterior, and Door •...
AC P s ervicer or call A C P C o m S e r v to ll free a t 1-866-4 26-26 21 inside the U .S.A . or C anad a. WARNING To avoid electrical shock which can cause severe personal injury or death, do not remove outer case at any time. Only an authorized ACP servicer should remove outer case.
As the mass of food increases, so will the necessary cook time. Refer to and comply with all USDA/FDA Food Code guidelines when cooking or heating food items. or full product documentation visit: 2016 ACP, Inc. www.acpsolutions.com Part No. 20037905...
Need help?
Do you have a question about the MFS18TS and is the answer not in the manual?
Questions and answers