Dvr-S200 D-Amp Module Troubleshooting / Dvr-S200 D-アンプモジュールの故障診断; Dvr-S200 Adjustment; Dvr-S200調整 - Yamaha DVX-S200 Service Manual

Home theater sound system
Hide thumbs Also See for DVX-S200:
Table of Contents

Advertisement

DVR-S200/NX-P200
DVR-S200 D-AMP MODULE TROUBLESHOOTING /
DVR-S200 D-アンプモジュールの故障診断
When there is a possibility of the D-Amp Module being de-
fective, use the following procedure to determine whether or
not it is defective.
Step 1
With the power turned off, remove one D-Amp Module and
then turn on the power to the main unit.
If the protection function still works, turn off the power, re-
move another D-Amp Module and then turn on the power to
the main unit. Repeat this procedure until the protection func-
tion stops working.
Step 2
When the protection function has stopped working, install
the removed D-Amp Modules one by one to the main unit
and then turn on the power.
If the protection function does not work, the D-Amp Module
installed then can be judged as normal.
If the protection function works, on the other hand, the D-
Amp Module installed then can be judged as defective.
Repeat this procedure to check all the removed D-Amp Mod-
ules.
Caution
Note that there is a rare case where two or more D-Amp Mod-
ules are defective.
DVR-S200 ADJUSTMENT / DVR-S200調整
Condition
• Start adjustment 5 sec or more after the power is turned
on.
• Headphones are not plugged in.
• No input signal.
DC Offset Adjustment
Adjust the potentiometer on each D-Amp Module so that the
DC voltage becomes 0 ± 10 mV at each speaker output.
22
D-アンプモジュールの故障が疑われる場合、 下記の方法によ
り各D-アンプモジュールの故障の有無を判定します。
Step 1
電源OFF状態でD-アンプモジュール1個を取り外した後、 本
機の電源をONします。
まだプロテクションが動作する場合、 電源をOFFし、 更にD-
アンプモジュール1個を取り外した後、 本機の電源をONしま
す。 プロテクションが動作しなくなるまでこれを続けます。
Step 2
プロテクションが動作しなくなったら、 取り外したD-アンプ
モジュールを1個ずつ本機に取り付け電源をONします。
プロテクションが動作しない場合、 その取り付けたD-アンプ
モジュールは正常と判断できます。
プロテクションが動作する場合、 その取り付けたD-アンプモ
ジュールは故障していると判断できます。
この方法により取り外した全てのD-アンプモジュールの故
障の有無を判定します。
注意
稀に2個以上のD-アンプモジュールが故障している場合があるので
注意が必要です。
条件
• 電源を入れてから5秒間以上経過後に調整を始めます。
• ヘッドホンは差し込みません。
• 無信号
DC オフセット調整
各スピーカー出力端子のDC電圧が 0 ± 10 mVになるように、
各D-アンプモジュールの半固定VRを調整します。
SURL ch
FL ch
FR ch
C ch
SURR ch

Advertisement

Table of Contents
loading

This manual is also suitable for:

Dvr-s200Nx-p200

Table of Contents