Summary of Contents for Sony KDL-26U2000 KDL-32U2000 KDL-42U2000
Page 1
All manuals and user guides at all-guides.com SE-1 RM-ED007 SE-1 SERVICE MANUAL CHASSIS MODEL MODEL COMMANDER DEST COMMANDER DEST KDL-26U2000 KDL-26U2000 RM-ED007 RM-ED007 KDL-32U2000 KDL-32U2000 RM-ED007 RM-ED007 KDL-40U2000 KDL-40U2000 RM-ED007 RM-ED007 KDL-26U2000 / KDL-32U2000 / KDL-40U2000 RM-ED007 FLAT PANEL COLOR TV - 1 -...
DUE TO LIVE CHASSIS, THE CHASSIS OF THIS RECEIVER IS PARTS LIST ARE CRITICAL FOR SAFE OPERATION. REPLACE DIRECTLY CONNECTED TO THE POWER LINE. THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
Due to the higher melting point of Lead Free Solder the soldering iron tip temperature needs to be set to 370 degrees centigrade. This requires soldering equipment capable of accurate temperature control coupled with a good heat recovery characteristics. For more information on the use of Lead Free Solder, please refer to http://www.sony-training.com - 3 -...
Page 4
All manuals and user guides at all-guides.com SE-1 RM-ED007 Sound Output LCD (Liquid Crystal Display) Panel KDL-26U2000 (26inches) Projected Picture Size KDL-32U2000 (32inches) Right and Left speaker 2 x 10W (RMS) KDL-40U2000 (40inches). Sub-woofer Input/Output Terminals [REAR] General Specifications Power Requirements 220 - 240V KDL-26U2000: Approx.
Page 5
All manuals and user guides at all-guides.com SE-1 RM-ED007 KDL-26U2000 KDL-26U2000 Model Name KDL-32U2000 KDL-32U2000 KDL-40U2000 KDL-40U2000 Item (AEP) (UK) RGB Priority Sub Woofer Scart 1 Scart 2 Front in (4) Projector Norm B/G Norm I Norm D/K Norm AUS Norm L Norm SAT Norm M...
All manuals and user guides at all-guides.com SE-1 RM-ED007 21 pin connector Pin No Signal Signal level Audio output B Standard level : 0.5V rms (right) Output impedence : Less than 1kohm* Audio input B Standard level : 0.5V rms (right) Output impedence : More than 10kohm* Audio output A...
All manuals and user guides at all-guides.com SE-1 RM-ED007 SE-1 SELF DIAGNOSTIC SOFTWARE The identification of errors within the SE-1 chassis is triggered in one of two ways :- 1: Busy or 2: Device failure to respond to IIC. In the event of one of these situations arising the software will first try to release the bus if busy (Failure to do so will report with a continuous flashing LED) and then communicate with each device in turn to establish if a device is faulty.
All manuals and user guides at all-guides.com The operating instructions mentioned here are partial abstracts from the Operating Instruction Manual. The page numbers of the Operating Instruction Manual remain as in the manual. 1: Checking the 2: Connecting an aerial/ 3: Bundling the cables 4: Preventing the TV accessories...
Page 9
All manuals and user guides at all-guides.com Watching TV Press to select the language Press the number buttons or PROG +/- to 6: Auto-tuning the TV displayed on the menu screens, then press select a TV channel. To select channel numbers 10 and above using the After selecting the language and country/region, a number buttons, enter the second and third digits Auto Start Up...
Page 10
All manuals and user guides at all-guides.com Do this Checking the Digital Electronic Programme Guide Viewing pictures from Access the Input Press to access the Input signal signal index table index table. (Then, only in (EPG) connected equipment analogue mode, press .) To select an input source, press then press...
Page 11
All manuals and user guides at all-guides.com Navigating through menus Picture Adjustment menu “MENU” allows you to enjoy various convenient features of this TV. You can easily select channels or external You can select the options listed below on the inputs with the remote.
Page 12
All manuals and user guides at all-guides.com Sound Adjustment menu Features menu You can select the options listed below on the You can select the options listed below on the Features Sound Adjustment Sound menu. To select options in “Settings”, Features menu.
Page 13
All manuals and user guides at all-guides.com Set-up menu Digital Set-up menu You can select the options listed below on the You can change/set the digital settings using the Set Up Set Up Set-up menu. To select options in “Settings”, see Digital Set-up menu.
Page 14
All manuals and user guides at all-guides.com Connecting to the TV (rear) Connecting optional equipment To connect Do this You can connect a wide range of optional equipment to your TV. Connecting cables are not supplied. PC D Connect to the PC sockets.
All manuals and user guides at all-guides.com Specifications F2–F10, B–Q, F21–F69 Sound Output Optional Accessories UHF B21–B69 KDL-40U2000: 10 W + 10 W (RMS) • Wall-Mount Bracket Digital: VHF/UHF KDL-32U2000: 10 W + 10 W (RMS) SU-WL51 (for KDL-40U2000) Display Unit Terminals KDL-26U2000: 10 W + 10 W (RMS) SU-WL31 (for KDL-32U2000 / KDL-26U2000)
Page 16
For example, the indicator flashes for two seconds, stops flashing for one second, and flashes for two seconds. Press 1 on the TV (top side) to switch it off, disconnect the mains lead, and inform your dealer or Channels Sony service centre of how the indicator flashes (duration and interval). When it is not flashing Problem Cause/Remedy Check the items in the tables below.
All manuals and user guides at all-guides.com SE-1 RM-ED007 SECTION 3 CIRCUIT ADJUSTMENTS 3-1. Electrical Adjustments Service adjustments to this model can be performed using the supplied remote Commander RM-ED007. BACKLIGHT How to enter into the Service Mode BACKLIGHT (0, 255) U BACKLIGHT (0, 10) Turn on the main power switch.
Page 24
All manuals and user guides at all-guides.com SE-1 RM-ED007 SOUND SERVICE MENU (0, 511) NORM_PAL_RD_H (+0, +1) NORM_PAL_RD_L (+0, +255) (-128, -1) NORM_PAL_GD_H (+0, +1) (+0, +127) (+0, +127) NORM_PAL_GD_L (+0, +255) NORM_PAL_BD_H (+0, +1) (-128, -1) (0, 1023) NORM_PAL_BD_L (+0, +255) Effect Mode (+0, +2)
All manuals and user guides at all-guides.com SE-1 RM-ED007 3-2. TEST MODE 2 Test Mode 2 is available by setting the TV for operation in Service Mode [ As shown on Page 23 ] , OSD ‘TT’ appears. The functions de- scribed below are available by selecting the two numbers.
13. M (Default value) is shown when AM sound is demodulated in MSP; A is shown when AFRIC demodulator is used. 14. S is shown when a SONY tuner is selected; P is shown when a PHILIPS tuner is selected (TT55).
All manuals and user guides at all-guides.com 4-1. BLOCK DIAGRAMS (1) TU1300 TUNER BLOCK TUNER ANALOG AGC SW TU AGC 12C SCL SW 12C SDA SW ANALOG IF BLOCK AUDIO SWITCH IC2000 SW1201 4 CHANNEL FILTER ANALOG +5VA SURFACE WAVE MULTIPLEXER/ DEMULTIPLEXER IF ANALOG...
All manuals and user guides at all-guides.com 4-1. BLOCK DIAGRAMS (4) (KDL-26/32U2000 ONLY) D6000 IC6000 PH6002 BRIDGE T6000 RECTIFIER SWITCHING CONTROL PHOTOCOUPLER V SENSE CN6003 PS6002 SIGNAL VCC D6011 3.15A DIODE VG(H) Q6003 SIGNAL VCC IC6002 TIMER VG(L) SIGNAL VCC SHUNT REGULATOR TO BDT BOARD Q6004...
All manuals and user guides at all-guides.com 4-1. BLOCK DIAGRAMS (5) 4-2. CIRCUIT BOARD LOCATION 5-2. CIRCUIT BOARD LOCATION Reference Information RESISTOR : METAL FILM H1/H1P : SOLID FPRD : NON FLAMMABLE CARBON G1 (KDL-26/32U2000) FUSE : NON FLAMMABLE FUSIBLE G2 (KDL-40U2000) : NON FLAMMABLE METAL OXIDE : NON FLAMMABLE CEMENT...
All manuals and user guides at all-guides.com ~ A1/A1P Printed Wiring Board Conductor Side B ~ ~ A1/A1P Printed Wiring Board Conductor Side A ~ ~ A1/A1P Board Semiconductor Voltage Table ~ ~ A1/A1P Board IC Voltage Table ~ (e)(s) (b)(g) (c)(d) Ref No...
Page 37
All manuals and user guides at all-guides.com BDT.-SE-1(KDL-26/32/40U2000) 3.3V_MAIN C5683 0 . 1 C5680 FB5680 C5682 NAND FLASH 0 . 1 2/11 C5684 0 . 1 R5686 R5691 +2V5D_DDR C5601 PLACE THESE CAPACITORS CLOSE TO IC PINS. NOTE PIN 6 IS NOT GND ON SAMSUNG IO/8 C5701 NAND FLASH, ONLY TOSHIBA...
All manuals and user guides at all-guides.com ~ BDT Printed Wiring Board Conductor Side A ~ ~ BDT Board Semiconductor Voltage Table ~ ~ BDT Board IC Voltage Table ~ - 47 -...
Page 48
All manuals and user guides at all-guides.com ~ BDT Printed Wiring Board Conductor Side B ~ - 48 -...
All manuals and user guides at all-guides.com ~ G1 Printed Wiring Board Conductor Side A ~ ~ G1 Board Semiconductor Location Table Side A ~ D6014 D - 5 IC6201 F - 7 DIODE D6000 K - 6 D6015 D - 7 IC6000 I - 3 IC6300...
Page 52
All manuals and user guides at all-guides.com ~ G1 Printed Wiring Board Conductor Side B ~ ~ G1 Board Semiconductor Location Table Side B ~ D6007 G - 4 D6012 L - 5 D6018 M - 7 D6203 H - 6 IC6001 I - 3 Q6005...
Page 53
All manuals and user guides at all-guides.com G2.-SE-1(KDL-40U2000) D6003(1) Q6001(1),Q6002(2),D6012(1) Mount Mech a A6001 263406601 D6003 Mount Mecha A6012 214976661 Q6001,Q6002,D6012 R6126 C6068 0 . 4 7 4 . 7 D6044 1/4W 100V FPRD 10ERB20-TB3 C6073 D6043 10ERB20-TB C6000 R6000 L6003 R6004 D6035(1)
Page 54
All manuals and user guides at all-guides.com TO H2/H2P BOARD CN9856 CN6300 G2.-SE1(KDL-40U2000) IC6300 TDA7495S STEREO POWER AMPLIFIER AUD_GND R6309 1/10W C6305 AUDIO_VCC AUD_GND C6302 JR6313 C6307 220p FB6304 0 . 1 JR6314 FB6302 C6300 JR6316 FB6301 220p C6304 R6306 JR6315 120k C6309...
All manuals and user guides at all-guides.com ~ G2 Printed Wiring Board Conductor Side A ~ ~ G2 Board Semiconductor Location Table Side A ~ DIODE D6206 I - 8 D6003 B - 8 D6207 I - 9 D6004 H - 8 D6012 D - 4 IC6001...
Page 56
All manuals and user guides at all-guides.com ~ G2 Printed WiringBoard Conductor Side B ~ ~ G2 Board Semiconductor Location Table Side B ~ D6200 F - 7 DIODE D6000 L - 8 D6203 F - 8 D6001 M - 1 D6204 F - 8 D6002...
All manuals and user guides at all-guides.com ~ H1/H1P Printed Wiring Board Conductor Side A ~ ~ H1/H1P Printed Wiring Board Conductor Side B ~ ~ H2/H2P Printed Wiring Board Conductor Side A ~ ~ H2/H2P Printed Wiring Board Conductor Side B ~ ~ H3/H3P Printed Wiring Board Conductor Side A ~ ~ H3/H3P Printed Wiring Board Conductor Side B ~ - 58 -...
All manuals and user guides at all-guides.com SECTION 5 EXPLODED VIEWS NOTE : Items with no part number and no description are not Items marked “*” are not stocked stocked because they are seldom required for routine since they are seldom required for service. routine service. Some delay should The construction parts of an assembled part are indicated be anticipated when ordering these with a collation number in the remarks column. items. 5-1. CHASSIS Revision 3.0 (Click inside red box to see related change) Note : The components identified by mark contain confidential information. Strictly follow the instructions when Revision 3.0 ever the components are repaired (Click inside red box to see related change)
All manuals and user guides at all-guides.com 5-2. STAND, REAR COVER, POWER LEADS 5-1. CHASSIS Cont Revision 3.0 (Click inside red box to see related change) REF.NO. PART.NO DESCRIPTION REMARK REF.NO. PART.NO DESCRIPTION REMARK *A-1189-410-A H3 BOARD, COMPLETE (26/32U2000UK/AEP) *A-1202-965-A H3P BOARD, COMPLETE (40U2000UK/AEP) 2-674-189-01 GUIDE, LIGHT NOT SERVICEABLE PART NOT SERVICEABLE PART NOT SERVICEABLE PART NOT SERVICEABLE PART Revision 3.0 (Click inside red box to see related change) - 62 -...
Page 63
All manuals and user guides at all-guides.com 5-2. STAND, REAR COVER, POWER LEADS Revision 3.0 (Click inside red box to see related change) UK models only Revision 3.0 Revision 3.0 (Click inside red box to see related change) (Click inside red box to see related change) REF.NO.
All manuals and user guides at all-guides.com SECTION 6 ELECTRICAL PARTS LIST PARTS LISTING TABLE OF CONTENTS Page A1/A1P BOARD COMPLETE Parts List : ....................65 H2/H2P BOARD COMPLETE Parts List : ....................68 H3/H3P BOARD COMPLETE Parts List : ....................
Page 90
All manuals and user guides at all-guides.com HISTORY KDL-26/32/40U2000 Model Name SERVICE MANUAL Click on Page Number to display detail of changes. Date Part Number Description of Revisions Version 2006.06 9-927-534-01 Original Manual 2006.09 9-927-534-81 Supplement 1 - Alternative panel, BDTR board replaces BDT board for KDL-26/32U2000.