Page 1
HISTORY Model Name KDL-26/32/37V4000 SERVICE MANUAL Click on Page Number to display detail of changes. Date Part Number Description of Revisions Version 2008.07 9-883-420-01 Original Manual.
Page 2
SE2AG SERVICE MANUAL CHASSIS MODEL DEST KDL-26V4000 OIRT / UK / WE KDL-32V4000 OIRT / UK / WE KDL-37V4000 OIRT / UK / WE RM-ED009 FLAT PANEL COLOR TV - 1 -...
COMPONENTS IDENTIFIED BY SHADING AND MARKED THE EXPLODED VIEWS AND IN THE PARTS LIST ARE CRITICAL FOR SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. - 2 -...
Due to the higher melting point of Lead Free Solder the soldering iron tip temperature needs to be set to 370 degrees centigrade. This requires soldering equipment capable of accurate temperature control coupled with a good heat recovery characteristics. For more information on the use of Lead Free Solder, please refer to http://www.sony-training.com - 3 -...
CONNECTORS 21 Pin Connector (SCART) Pin No Signal Signal level Audio output B Standard level : 0.5V rms (right) Output impedence : Less than 1kohm* Audio input B Standard level : 0.5V rms (right) Output impedence : More than 10kohm* Audio output A Standard level : 0.5V rms (left)
Page 7
HDMI Connector Pin No Signal Assignment Pin No Signal Assignment TMDS Data2+ TMDS Clock Shield TMDS Data2 Shield TMDS Clock- TMDS Data2- TMDS Data1+ Reserved (N.C. on device) TMDS Data1 Shield TMDS Data1- TMDS Data0+ DDC/CEC Ground TMDS Data0 Shield +5V Power TMDS Data0- Hot Plug Detect...
SE2AG SELF DIAGNOSTIC SOFTWARE The identification of errors within the SE2AG chassis is triggered in one of two ways :- 1: Busy or 2: Device failure to respond to IIC. In the event of one of these situations arising the software will first try to release the bus if busy (Failure to do so will report with a continuous flashing LED) and then communicate with each device in turn to establish if a device is faulty.
SECTION 2 DISASSEMBLY 2-1. Rear Cover Removal 2-2. Stand Removal => = > => = > => => => To remove the ‘Rear cover’ remove the 25 fixing screws indicated To remove the ‘Stand’ remove the 3 fixing screws indicated. and pull the rear cover gently backwards away from the TV set.
2-5. BC1 Board Removal 2-6. GA2 Board Removal (26/32 inches) Screws Screws To remove the ‘BC1’ board disconnect all connectors and then remove To remove the ‘GA2’ board disconnect all connectors and then remove the 6 screws circled and ease the board gently away from the back of the the 4 screws circled and ease the board gently away from the back of the TV set.
SECTION 3 ADJUSTMENTS 3-1. How to enter the Service Mode Service adjustments to this model can be performed using the supplied remote commander RM-ED009. BACKLIGHT BACKLIGHT (0, 255) U BACKLIGHT (0, 10) Turn on the power to the TV set and enter into the stand-by BL SETUDEN (0, 255) mode.
3-2. TT MODES TT mode is available by setting the TV for operation in Service Mode [ As shown on Page 10 ] , OSD ‘TT’ appears. The functions described below are available by selecting the two numbers. To release the ‘Test mode 2’, press 00, 10, 20 ... twice or switch the TV set into Stand-by mode.
Page 14
3-3. TT OSD Labels T T - " E C S C B A N o r m (20) (25) D D C (21) (10) (11) (12) (22) (26) (13) (14) (15) (16) (17) (18) (19) (23) (24) Key: Panel size configuration. Changed by TT61...TT68. D/A: D is shown when Digital mode is enabled;...
Page 20
BC1 - SE2AG MOUNT ALL THESE CONNECTORS IN THE "FE" AREA *** MOUNT *** JL7501 FIT FOR JTAG CN7500 +3V3D TP7500 SIGN15457 JL7503 TXD0B_MAIN FE_TXD0B AVC/EMMA COMMS JL7504 FE_RXD0B RXD0B_MAIN JL7505 TXD1B_MAIN FE_TXD1B JIG PORT JL7506 FE_RXD1B RXD1B_MAIN TXD3B_MAIN JL7507 AVC DEBUG SIGN15453 RXD3B_MAIN...
Page 27
BC1 - SE2AG CHIP R4300 Audio,Analog Video input & DDR Interface D_31 V IN 22 DRD_31 C4312 0 . 1 D_30 PC_BLUE V IN 21 DRD_30 TC7S66FU(TE85R) C4313 0 . 1 D_29 PC_GREEN IC4300 V IN 20 DRD_29 D_28 PC_RED C4314 0 .
Page 28
BC1 - SE2AG JL4101 3.3V_STBY C4104 100p 3.3V_STBY PZU5.6B2 D4105 1005 CAT24C32WI-GT3(E) C4129 FB4118 IC4104 6.3V C4130 JL4102 0 . 1 KEY2 1005 JL4116 C4100 JL4117 100p PZU5.6B2 KEY2 D4104 1005 FB4119 CN4102 JL4118 NVM_WP Q4110 RT1N441C-TP-1 R4200 C o n t r o l a n d D i g i t a l +3.3IO 1/16W Video I/O...
Text Search ~ BC1 Printed Wiring Board Side A ~ I C 7 1 0 0 I C 4 5 6 1 ~ H3E Printed Wiring Board Side A ~ I C 3 4 0 2 C N 3 0 1 CN3200 I C 7 3 0 1 C N 4 1 0 2...
Text Search ~ BC1 Printed Wiring Board Side B ~ I C 6 4 0 4 I C 7 8 0 0 C N 7 5 0 1 I C 6 4 0 5 I C 6 4 0 5 ~ H4/H4K Printed Wiring Board Side A ~ I C 7 3 0 9 C N 4 0 1...
Text Search ~ GA2 Printed Wiring Board Side A ~ C N 6 2 0 3 S - V C C S - G N D + 1 2 V G N D C 6 4 2 6 J W 6 6 0 5 J W 6 3 0 1 J W 6 0 0 2 C N 6 2 0 0...
Page 36
Text Search ~ GA2 Printed Wiring Board Side B ~ J W 6 0 0 2 J W 6 0 0 9 S - G N D S - V C C C 6 4 2 6 G N D + 1 2 V J W 6 6 0 5 J W 6 0 0 5...
SECTION 5 EXPLODED VIEWS NOTE : Non-serviceable items with no part number and no Items marked “*” are not stocked since they are seldom required for description are not stocked because they are not required for routine service. routine service. Some delay should The construction parts of an assembled part are indicated be anticipated when ordering these with a collation number in the remarks column.
....................58 Note: To ensure safety and reliability it is Sony policy that power supply boards should not be repaired at component level in the field as a result... The GA2 and GA3 boards are regarded as non service items for...
Page 43
Note : The components identified by mark contain confidential information. Strictly follow the instructions when ever the components are repaired and/or replaced. REF.NO. PART.NO DESCRIPTION REMARK REF.NO. PART.NO DESCRIPTION REMARK A-1599-690-A BC1 Board, Complete C2072 1-100-916-11 CERAMIC CHIP 0.1UF C2073 1-100-916-11 CERAMIC CHIP 0.1UF <...