Philips 26MD257B/37 Service Manual page 114

12
TPM1.0U LA
5.2 Factory Mode
It can enter Factory Mode
1. Press" Menu" in normal operation mode to enter OSD.
2. Press "062596+Menu" on the button (RC) remote control in OSD.
3. Press "Menu" again. The screen will appear "FAC" in top right corner.
OSD behavior:
Before press number key change OSD item
Now remove previous function, press number key then press OK will change value
Item
//Action Items
0 Exit Factory
1 RESET_SPC
2 RESET_CSM_CODE
3 AUTO_COLOR
//Switch Items
4 VIRGIN Mode
5 AGING MODE
6 GAMMA_TABLE
7 COLOR_ENHANCE
8 SET_PIN
9 ORT_MODE
//ADC Gain & Offset
10 ADC_GAIN_R
11 ADC_GAIN_G
12 ADC_GAIN_B
13 ADC_OFFSET_R
14 ADC_OFFSET_G
15 ADC_OFFSET_B
//Color Temperature
16 CLR_TEMP_R
17 CLR_TEMP_G
18 CLR_TEMP_B
//Smart Picture
19 SP_MODE_3DNR
20 SP_MODE_PWM
//Smart Picture Default
21 SP_GAIN_BRI_DTV
22 SP_GAIN_BRI_AV
23 SP_GAIN_BRI_YPBPR
24 SP_GAIN_BRI_HDMI
25 SP_GAIN_BRI_VGA
26 SP_GAIN_CNT_DTV
27 SP_GAIN_CNT_AV
28 SP_GAIN_CNT_YPBPR
29 SP_GAIN_CNT_HDMI
30 SP_GAIN_CNT_VGA
31 SP_GAIN_TINT_DTV
32 SP_GAIN_TINT_AV
33 SP_GAIN_TINT_YPBPR
34 SP_GAIN_TINT_HDMI
35 SP_GAIN_CLR_DTV
36 SP_GAIN_CLR_AV
5. Service Modes, Error Codes and Fault Finding
Description
reset item SP_GAIN_BRI_XXX to
SP_GAIN_CLR_XXX to default value
Reset CSM ERROR Code to 0
PC: any pattern has black and white
YPbPr:SMPTEbar(color bar), any timing.
turn<On> and no signal input
use gamma table or not
if On, AC switch on/off turn on the TV
(values different by VGA and YPbPr)
AutoColor changes those items
(values different by AV,VGA,DTV,HDMI,YPbPr)
Back-End Scaler R G B Gain
(values different by smart picture)
Except YPbPr 720P above timing
(when Dynamic contrast Off)
(values different by AV,DTV,HDMI,YPbPr)
Front-End, because each source has the
same smart picture setting, for different
between each source
Brightness
Contrast
Color
Color
Range method of operation
press OK.
press OK.
press OK.
press OK. when autocolor, the OSD disappear,
when finished. OSD appear.
On/Off
On/Off
On/Off
On/Off
On/Off
On/Off
0~255 Press Left and Right to change value
0~255
0~255
0~127
0~127
0~127
0~255 Press Left and Right to change value
0~255
0~255
0~5 Press Left and Right to change value
0~255
0~255 Press Left and Right to change value
0~255
0~255
0~255
0~255
0~255
0~255
0~255
0~255
0~255
0~255
0~255
0~255
0~255
0~255
0~255
Status
Pass
Pass
Pass
Pass
Pass
Pass
Pass
Pass
Pass
Pass
Pass
Pass
Pass
Pass
Pass
Pass
Pass
Pass
Pass
Pass
Pass
Pass
Pass
Pass
Pass
Pass
Pass
Pass
Pass
Pass
Pass
Pass
Pass
Pass