Table of Contents
Advertisement
Section 1: Assembly & Setup
Section 1: Assembly & Setup
Tractor Requirements
!
WARNING
To avoid serious injury or death:
Lightweight tractors with rear attached implements may need
weights added to the front to maintain steering control.
Consult your tractor Operator's Manual to determine proper
weight requirements and maximum weight limitations.
Tractor horsepower should be within the range noted
below. Tractors outside the horsepower range must not
be used.
Horsepower rating . . . . . . . 65-100 hp (48.5-74.6 kW)
Rear Power Take-Off shaft type . . . . . .1 3/8"-6 Spline
Rear Power Take-Off speed . . . . . . . . . . . . . 540 rpm
Hitch type . . . . . . . . . . . . . . . . . . . . . . . . . . . Draw bar
Hydraulic duplex outlets required:
Without optional hydraulic transport locks . . . . . . . 1
With optional hydraulic transport locks . . . . . . . . . 2
Electrical Hook-up (See Figure 1-1) . . . . . 7-Pin Outlet
Ballast requirements . . . . . . . . . . See warning above
Electrical Hook-up
Refer to Figure 1-14:
The LED wire harness is equipped with a 7-way round pin
connector for connecting to the tractor's 7-pin electrical
outlet shown in Figure 1-5.
11640
Tractor 7-Pin Electrical Outlet
Figure 1-1
Hardware Torque Information
When tightening hardware, refer to "Torque Values
Chart for Common Bolt Sizes" on page 52 to determine
standard torque values. Refer to "Additional Torque
Values" at the bottom of the chart for exceptions to the
standard torque values.
Dealer Preparations
This mower has been partially assembled at the factory.
some additional preparations will be necessary to finish
assembling the mower and to attach it to the customer's
tractor. Ensure that the intended tractor conforms to the
requirements stated under the heading
"Tractor Requirements".
11/18/21
Table of Contents
Pre-Assembly Checklist
Make sure miscellaneous assembly tools are on hand:
Hammer, tape measure, hacksaw, assortment of wrenches and
sockets, 3/8" drill, drill bits and spirit level.
Have a forklift or hoist with properly sized chains and safety
stands on hand capable of lifting 2500 lbs.
Have a minimum of two people available during assembly.
Check to see if auxiliary tractor weights are needed.
Make sure all major components and loose
parts are shipped with the machine.
Double check to make sure all fasteners and
pins are installed in the correct location. Refer
to the Parts Manual if unsure.
NOTE: All assembled hardware from the factory
has been installed in the correct location.
Remember location of a part or fastener if
removed during assembly. Keep parts
separated.
Make sure working parts move freely, bolts are
tight and cotter pins are spread.
Make sure all red and amber reflectors are
correctly located and visible when machine is in
transport position.
Make sure all safety labels are correctly located
and legible. Replace if damaged.
80-90 EP Gear Lube must be added to the
gearbox and motor as indicated in the
"Maintenance & Lubrication" Section.
Make sure all tires are inflated to the specified
psi air pressure.
Make sure all wheel bolts and axle nuts are
tightened to the specified torque.
Tractor Shutdown Procedure
The following are basic tractor shutdown procedures.
Follow these procedures and any additional shutdown
procedures provided in your tractor Operator's Manual
before leaving the operator's seat.
1.
Reduce engine speed and disengage power take-off
if engaged.
2. Park tractor and implement on level, solid ground.
3. Lower implement to ground or onto non-concrete
support blocks.
4. Put tractor in park or set park brake, turn off engine,
and remove switch key to prevent unauthorized
starting.
5. Relieve all hydraulic pressure to auxiliary hydraulic
lines.
6. Wait for all components to come to a complete stop
before leaving the operator's seat.
7.
Use steps, grab-handles and anti-slip surfaces when
stepping on and off the tractor.
Check
AFM4522 All-Flex Grooming Mower 315-360M
Ref.
Operator's
Manual
Operator's
Manual:
315-360M
Parts Manual:
315-360P
Operator's
Manual
Page 1
Page 6
Page 43
Page 52
Page 52
15
Advertisement
Table of Contents
