Transport; Working Instructions - PrimAster TS2200 Translation Of Original Operating Manual

Fig. 9
Fasten the wheel assembly (16) to the rear base legs
(4 and 5) using 4 hexagon bolts M6 x 16, 4 washers
6, and 4 nuts M6.
Fig. 10
Place the machine on its feet and firmly tighten all
bolts of table, legs and braces (except those of the
wheel assembly).
Fig. 11
Firmly tighten the wheel assembly in the position
where the wheels slightly touch the ground.
Fig. 12 / 12.1
Fasten the riving knife in line with the saw blade as
described in the illustration. Slightly release the bolt
without removing it. Retighten it firmly after reset-
ting. For doing this, it is necessary to remove the saw
blade insert (19, Fig. 13).
Fig. 13
After setting the riving knife, refasten the saw blade
insert (19) with 4 countersunk bolts M6 x 16.
Fig. 14
Fasten the cover (20) to the riving knife (18) with
roundhead bolt M6 x 25, washer 6, and wing nut M6.
Fig. 15
Connect the suction hose (21) to the suction hood
(20) and the suction nozzle.
Fig. 16 / 16.1
Fasten the hooked bolt to the right-hand leg side us-
ing 2 washers 6 and 2 nuts M6. The hook serves for
storing the saw blade key and the push stick.
The 2 transport handles are attached at the left and
right leg at the front of the saw using 4 hexagon bolts
M6 x 16, 4 washers 6, and 4 nuts M6.
Assembly of the longitudinal fence, Fig.17 / 17.1
/ 17.2
1 Mount the guide rail (A) with two hexagon bolts M6
x 16 with nuts M6 (B) to the front side of the table.
2 Mount the two clamping levers (C) to the table and
the guide rail using two lock bolts M6 x 25.
3 Place the swinging part (D) into the guide rail, set the
scale to 0°, and firmly tighten the clamping handle (E).
Attention: For longitudinal cutting, the swinging part
must always be set to 0.
4 Depending on the type of job, push the guide rail
(G) into the guide bolts (F) with the high (Fig. 18.1)
or low surface (Fig. 18.2) and tighten them firmly.
5 Set the fence rail to the desired dimension and
tighten both clamping levers (C).
Assembly of the cross-cutting gauge, Fig. 18.1 /
18.2 / 18.3
1 Mount the guide rail with two hexagon bolts M6
x 16 and two nuts M6 to the left side of the table.
28 І 48
2 Place the swinging part (D) into the guide rail. The
swinging part must slide easily.
3 Depending on the type of job, push the guide rail
(G) into the guide bolts (F) with the high (1) or low
surface (2) and tighten them firmly.
4 Set the fence rail (G) to the desired degree between
+60° and -60° and tighten the clamping handle (E).
Changing the sawblade, Fig. 19
Caution! Pull out the main plug and wear safety
gloves.
Release the wing screw of the suction hood (20) and
remove the hood.
Fig. 20
Release the 4 Phillips screws of the table insert (19)
and remove the insert.
Fig. 21
Move the saw blade to the very top and release the
bolt with the saw blade key.
Attention: Left-handed thread.
Fig. 22
Remove the saw blade flange (31) and the saw blade
(32). Then change the saw blade.
When mounting the saw blade mind the recess.
After changing the saw blade, check the setting of
the riving knife and refit the table insert (19) and the
suction hood (20).

9. Transport

The machine may only be transported with suitable
lifting devices (crane or fork lift). The connection point
for the rope (crane) is on the upper band wheel cabi-
net. Never lift from the saw bench. If the machine is to
be moved frequently within the work area, use of the
wheel assembly special accessory is recommended.

10. Working instructions

After each new adjustment it is advisable to carry out
a trial cut in order to check the set dimensions. After
switching on the saw, wait for the blade to reach its
maximum speed of rotation before commencing with
the cut.
Secure long workpieces against falling off at the end
of the cut (e.g. with a roller stand etc.)
Take extra care when starting the cut!
Never use the equipment without the suction func-
tion.
Regularly check and clean the suction channels.
Make sure, that you select a saw blade that is appro-
priate for the material you intend to cut.
Connect the power tool to a dust reception facility
when cutting wood.
Do not use saw blades made out of high-speed steel
(HSS steel).
Use the push stick or the feed lever for sliding the
wood, to guide it safely past the saw blade.