Technical Data; Attachment And Operation - PrimAster TS2200 Translation Of Original Operating Manual

7. Technical Data

AC motor w
performance
operating mode
Idle speed
Hard-metal blade
Number of teeth
table size
Cutting height max. 90°
Cutting height max. 45°
height adjustment
saw blade swivel
weight
* operating mode S6 40%: Continuous opera-
tion with intermittent loading (playing time 10 min).
Engine protection of to hot warming up:
It´s allowed to run the engine with nominal power maxi-
mum 40% of playing time. After this the machine must run
60% of playing time steadily without load.
Noise values
The total noise values determined in accordance
with EN 61029.
sound pressure level L
pA
uncertainty K
pA
sound power level L
WA
uncertainty K
WA
Wear hearing protection.
The effects of noise can cause a loss of hearing.
Total vibration values (vector sum - three directions)
determined in accordance with EN 61029.

8. Attachment and operation

Before starting the equipment
• All covers and safety devices have to be properly
fitted before the equipment is switched on.
• It must be possible for the blade to run freely.
• When working with wood that has been processed
before, watch out for foreign bodies such as nails
or screws, etc.
• Before you press the ON/OFF switch check that the
saw blade is fitted correctly. Moving parts must run
smoothly.
• Before you connect the equipment to the power
supply make sure the data on the rating plate are
dentical to the mains data.
• Connect the machine to a properly installed pro-
tective contact socket, with at least 16A circuit
breaker.
230V~ 50Hz
2200 W
S6 40%*
2800 min
-1
ø 315 x ø 30 x 3 mm
24
800 x 550 (950) mm
83 mm
49 mm
0 - 83 mm
0 - 45°
44 kg
94,5 dB(A)
3 dB
105,2 dB(A)
3 dB
Attachment
Important. Pull out the power plug before carrying out
any maintenance, resetting or assembly work on the
circular saw!
Place all parts supplied on a flat surface. Grouping
equal parts.
Note: If compounds with a bolt (round head / or hexa-
gon), hex nuts and washers are backed up, the wash-
er must be fitted under the nut.
Insert screws each from outside to inside. Secure
connections with nuts on the inside.
Note: Tighten the nuts and bolts during assembly
only to the extent that they can not fall down.
If you tighten the nuts and bolts prior to final assem-
bly, final assembly can not be performed.
Fig. 1
Place the table top (1) onto a work bench after having
removed the packing pad a underneath the motor.
Fig. 1.1
Fasten the base leg (2) onto the table top using 2
hexagon bolts M6 x 16, 2 washers 6 and 2 nuts M6.
Tighten the bolts slightly by hand.
Fig. 2
Fasten the switch (6) to the table top using 2 hexagon
bolts M6 x 16, 2 washers 6, and 2 nuts M6.
Fig. 3
Fasten the base leg (3) to the table top using 2 hexa-
gon bolts M6 x 16, 2 washers 6, and 2 nuts M6.
Fig. 4
Fasten the base leg (4) to the table top using 2 hexa-
gon bolts M6 x 16, 2 washers 6, and 2 nuts M6.
Fig. 5
Fasten the base leg (5) and the hose holder to the
table top using 2 hexagon bolts M6 x 16, 2 washers
6, and 2 nuts M6.
Fig. 6 / 6.1
Fasten 2 longitudinal braces (10) and 2 cross braces
(9) onto the base legs (2, 3,4 and 5) using 12 hexa-
gon bolts M6 x 16, 12 washers 6, and 12 nuts M6.
Fig. 7 / 7.1 / 7.2 / 7.3
Fasten the table extension plate (8) with 2 braces
11 and cross brace to the table top using 6 hexagon
bolts M6 x 16, 6 washers 6, and 6 nuts M6.
Tighten the bolts slightly by hand. (The table length
extension (8) can also be used as table width exten-
sion by fitting it to the side with the shorter braces.)
Fig. 8
Fasten the suction piece (14) to the lower saw blade
guard (13) using 4 hexagon bolts M4 x 10.
27 І 48