Related Manuals for ABACO MACHINES AVL480
Summary of Contents for ABACO MACHINES AVL480
- Page 1 ABACO MACHINES OPERATION MANUAL ABACO GLASS VACUUM LIFTER (AVL480) ABACO MACHINES (USA) 14508 S. Garfield Ave., Paramount, CA 90723, USA Tel : 310-532-0366 Fax : 310-532-0499 Email : sales@abacomachines.com Website : www.abacomachines.com...
- Page 3 I.GENERAL: - Abaco Glass Vacuum Lifter is the equipment that is designed to use for lifting and moving large size glass. - This item has ability to rotate up to 90 degree vertically and horizontally. - There are two ways of suction cups positioning which fit well with various size of glass.
- Page 4 Specifications: AVL480 Model 1056 lbs (480 kg) Work Load Limit (W.L.L) 9 ¹³⁄₁₆ ” (250mm) Diameter of suction cup Number of suction cups ” ” 70 ⅞ x 39 ⅜ Minimum applicable size of glass sheet (1800x1000mm) Rotate angle Left 90 , Right 90...
-
Page 5: Structure Specifications
III. STRUCTURE SPECIFICATIONS: 1. Overall:... - Page 6 POS. CODE DESCRIPTION QTY. AVL480-01 Main frame AVL480-02 Hanger AVL480-03 Bushing AVL480-04 Washer Ø20 AVL480-05 Bolt M20x40 AVL480-06 Shaft 1 AVL480-07 Pad 1 AVL480-08 Traverse beam, left AVL480-09 Allen bolt M6x12 AVL480-10 Swivel plate AVL480-11 Pad 2 AVL480-12 Pad 3...
- Page 7 AVL480-29 Plastic plate AVL480-30 Motor AVL480-31 Bolt M6x25 AVL480-32 Plastic bushing AVL480-33 Rubber cap 1 AVL480-34 Bolt AVL480-35 Rubber cap 2 AVL480-36 Suction cup AVL480-37 Spring AVL480-38 Pad 5 AVL480-39 Turn-knob M10 AVL480-40 Traverse beam, right AVL480-41 Circlip Ø14 AVL480-42 Washer Ø14...
- Page 8 IV. INSTRUCTION FOR USE: 1. Before operating: - Ensure the equipment is connected to suitable voltage power (See section II) - Ensure the power is continuous supplied during the whole operate process. - Inspect the air tube system, ensure there is not sign of leaking or breaking.
- Page 9 Step 2: Place the glass vacuum lifter closely to the glass surface. Note: Ensure that the glass surface is well attracted by all the suction cups simultaneously. Step 3: Press “ VACUUM ” (green button) to activate attract...
- Page 10 Step 5: Place the glass in desired position. Note: - Gently operate when lifting the glass up and down. - Do not switch lever to adjust the angle to 90 degree and set the glass in vertical dimension while attracting. Step 6: Press “RELEASE”...
- Page 11 Note: Once press “VACUUM’’ button, the pressure gauge hand will move to the right. Please make sure that the hand is in the section from -0.8 bar -1 bar. Step 4: Starting lifting and moving the glass. While the system is in attract mode, we can rotate the glass to 90 degree.
- Page 12 B. When the glass is positioned in horizontal dimension. - Before activate attracting function , adjusting the lifter's inclination so that all the suction cups are in horizontal position. See Appendix 3.A Step 1: Moving the lifter to get closed to the glass. Note: -Adjusting the suction cups position to adapt to the glass size (See appendix 3.B)
- Page 13 Step 2: Place the lifter closely to the glass surface. Note: Make sure that all the suction cups need to be attracting to the glass surface. Step 3: Press “VACUUM” (green button) to activate attracting.
- Page 14 Note: Once press “VACUUM” button, the pressure gauge hand will move to the right. Please make sure that the hand is in the section from -0.8 bar -1 bar. Step 4: Starting lifting and moving the glass. While the system operate, we can rotate the glass to 90 degree direction.
- Page 15 Step 5: Place the glass in desired position. Note: Operate carefully when the glass up and down.
- Page 16 Step 6: Press “RELEASE” button and remove the lifter from the glass. Note: Ensure that the pressure gauge lower down to “0” before remove the lifter.
- Page 17 3. Appendix: A/ Adjusting the suction cups to horizontal dimension. Pull the handgrip lock (as shown in the picture) and rotate the frame to horizontal dimension.
- Page 18 - Loosen turn-knob (anticlockwise direction). - Move suction cup follow to requirement place, tighten turn-knob (clockwise direction)
- Page 19 C/ Rotating main frame manipulation. - Pull the handgrip lock (as shown in the picture) - Next, rotate the glass vacuum lifter follow to your requirement. Note: Pin-clock automatically install into hole position for angle adjustment.
-
Page 20: Inspection And Maintenance
INSPECTION & MAINTENANCE Schedule periodic maintenance of the lifter, especially the suction cups. Reserve expendable and/or necessary spare parts for maintenance or repair. - Check the electrical system, turn off the power after use. Regularly check the tightening conditions of all the bolts and nuts. -
Page 21: Warranty Certificate
WARRANTY CERTIFICATE You are kindly requested to read the following carefully. PERIOD The warranty starts from the date of purchase (date on distributors invoice). Warranty is valid for a period of twelve (12) months WARRANTY This warranty is limited only to provide replacements of the parts recognized by the Company as defective (excluding worn- outs and consumables.) The Company is not responsible for any misuse or abuse of the... - Page 22 THIS MANUAL SHALL BE REVISED WITHOUT PRIOR NOTICE FOR IMPROVEMENT PURPOSES Copyright: Abaco Machines. DO NOT COPY AND/OR QUOTE THE CONTENTS WITHOUT PRIOR WRITTEN CONSENTS OF ABACO MACHINES...