Advertisement
Quick Links
sauder.com
Side Table
Palladia Collection | Model 420519
Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-523-3987.
Share your journey!
Gets on your couch' s
good side.
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-23
Français pg 24-26
Español pg 27-29
Lot # 500889
12/14/16
Purchased: __________________
Be sure to give us a ring before
making any returns. 1-800-523-3987
Advertisement
Related Manuals for Sauder Palladia 420519
Summary of Contents for Sauder Palladia 420519
- Page 1 Palladia Collection | Model 420519 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. PLEASE READ AND KEEP FOR FUTURE REFERENCE. Prefer the phone? Call 1-800-523-3987.
- Page 2 Assembly Tools Required Part Identifi cation No. 2 Phillips Screwdriver Tip Shown Actual Size Hardware Identifi cation Assembly Steps 5-23 Hammer Not actual size Français 24-26 Español 27-29 Skip the power trip. Safety This time. Warranty Page 2 420519 www.sauder.com/services...
- Page 3 BACK SKIRT (1) SIDE SKIRT (2) TOP MOLDING (2) TOP SIDE MOLDING (2) UPPER PLINTH (2) EXTENSION BLOCK (2) COLUMN MOLDING (2) RIGHT VERTICAL MOLDING (1) LEFT VERTICAL MOLDING (1) HALF DISK (2) LOWER PLINTH (2) www.sauder.com/services 420519 Page 3...
- Page 4 SILVER 1-1/8" FLAT HEAD SCREW - 8 BLACK 1/2" FLAT HEAD SCREW - 4 12S BROWN 1" FLAT HEAD SCREW - 6 GOLD 1" MACHINE SCREW - 1 113S BLACK 1-15/16" FLAT HEAD SCREW - 6 Page 4 420519 www.sauder.com/services...
- Page 5 Assemble your unit on a carpeted fl oor or on the empty å carton to avoid scratching your unit or the fl oor. To begin assembly, push a SAUDER TWIST-LOCK® å FASTENER (7F) into the large holes in the ENDS (A and B). Repeat this step for the SHELF (E) and VERTICAL MOLDINGS (R and S).
- Page 6 Step 2 Fasten the VERTICAL MOLDINGS (R and S) to the å ® How to use the SAUDER TWIST-LOCK FASTENER ENDS (A and B). Tighten four TWIST-LOCK® FASTENERS. 1. Insert the dowel end of the FASTENER into the hole of the adjoining part.
- Page 7 Remember: Righty tighty. Lefty loosey. These edges must be even. BLACK 1-1/4" FLAT HEAD SCREW Curved edge (8 used in this step) These edges must be even. These edges will have 1/2" off set. Curved edge www.sauder.com/services 420519 Page 7...
- Page 8 Fasten the SHELF (E) to the ENDS (A and B). Tighten four å TWIST-LOCK® FASTENERS. Notch S u r f a c I S T i t h F A S - L O T E N ® E R S Page 8 420519 www.sauder.com/services...
- Page 9 WOOD DOWEL in the long edge inserts into the hole in the VERTICAL MOLDING (R). Repeat steps 1 and 2 fastening the remaining EXTENSION å BLOCK (P) to the SHELF (E) and VERTICAL MOLDING (S). Insert the WOOD DOWELS into the holes closest to the ENDS. www.sauder.com/services 420519 Page 9...
- Page 10 EXTENSION BLOCKS (P). Use six BLACK 1-15/16" FLAT HEAD SCREWS (113S). S u r f a c r e h i t h o l e 113S BLACK 1-15/16" FLAT HEAD SCREW (6 used in this step) Page 10 420519 www.sauder.com/services...
- Page 11 NOTE: Be sure the BRACKETS are even with the edges of å the BRACE and SKIRTS. NOTE: Use the exact holes shown. å BLACK 9/16" LARGE HEAD SCREW (12 used in this step) (12 used) Finished edge Finished edge www.sauder.com/services 420519 Page 11...
- Page 12 Fasten the SIDE SKIRTS (L) to the BOTTOM (D), BRACE (G), å and BACK SKIRT (K). Use eight BLACK 9/16" LARGE HEAD SCREWS (1S). BLACK 9/16" LARGE HEAD SCREW (12 used in this step) Finished edge Finished edge Page 12 420519 www.sauder.com/services...
- Page 13 Use two BROWN 1" FLAT HEAD SCREWS (12S). Fasten the BASE MOLDING (I) to the BRACE (G). Use two å BROWN 1" FLAT HEAD SCREWS (12S). These edges must be even. BROWN 1" FLAT HEAD SCREW (4 used in this step) www.sauder.com/services 420519 Page 13...
- Page 14 Step 10 Fasten the LOWER PLINTHS (U) to the BRACE (G). Use å four BLACK 1-1/4" FLAT HEAD SCREWS (7S). Rounded edge BLACK 1-1/4" FLAT HEAD SCREW (4 used in this step) Page 14 420519 www.sauder.com/services...
- Page 15 Step 11 Carefully stand your unit upright. å Now might be a Slide the BACK (F) into the grooves in the ENDS (A and B). å good time to refresh your drink. www.sauder.com/services 420519 Page 15...
- Page 16 Tap four MOLDING CONNECTORS (19F) into the notches å in the MOLDINGS (M and N). (19F) Use your hammer to tap the MOLDING CONNECTORS into the notches in the MOLDINGS. Flat end Flat end Flat end Page 16 420519 www.sauder.com/services...
- Page 17 Flip the MOLDINGS (M and N) over and fasten them to the å TOP (C). Use eight SILVER 1-1/8" FLAT HEAD SCREWS (10S). NOTE: Do not overtighten the SCREWS into the TOP. å SILVER 1-1/8" FLAT HEAD SCREW (8 used in this step) Rounded edge Rounded edge www.sauder.com/services 420519 Page 17...
- Page 18 Step 14 Fasten the TOP SIDE MOLDINGS (N) on the TOP (C) to the å ENDS (A and B). Tighten four TWIST-LOCK® FASTENERS. Rounded edge Rounded edge Page 18 420519 www.sauder.com/services...
- Page 19 Step 15 Fasten two HINGES (14H) to the DOOR (H). Use four å BLACK 1/2" FLAT HEAD SCREWS (11S). BLACK 1/2" FLAT HEAD SCREW (4 used in this step) www.sauder.com/services 420519 Page 19...
- Page 20 Step 16 You have the option to fasten the DOOR (H) to swing å open to the right or left of your SIDE TABLE as shown below. DOOR OPENS LEFT DOOR OPENS RIGHT Page 20 420519 www.sauder.com/services...
- Page 21 Push a DOOR STOP (4I) into the SHELF (E) as shown according to your door confi guration. å DOOR OPENS LEFT DOOR OPENS RIGHT Stop Stop Mounting Mounting screw screw Hinge Hinge GOLD 1" MACHINE SCREW (1 used for the KNOB) www.sauder.com/services 420519 Page 21...
- Page 22 DOORS in or out, as needed. Tighten the mounting screw after making adjustments. DOOR OPENS LEFT DOOR OPENS RIGHT Mounting screw (depth) Mounting screw (depth) Adjusting screw (horizontal) Adjusting screw (horizontal) (vertical adjustment) (vertical adjustment) Page 22 420519 www.sauder.com/services...
- Page 23 This completes assembly. Clean with your favorite furniture polish or a damp cloth. Wipe dry. å And to celebrate, why not share your success story? DOOR OPENS LEFT DOOR OPENS RIGHT (4 used) 50 lbs. 50 lbs. 15 lbs. 15 lbs. 30 lbs. 30 lbs. www.sauder.com/services 420519 Page 23...
- Page 24 élément et conserver le livret pour future référence. EXTRÉMITÉ DROITE ..........1 FIXATION TWIST-LOCK® ........12 Pour contacter Sauder EXTRÉMITÉ GAUCHE ..........1 15F CHEVILLE EN BOIS ...........4 en ce qui concerne cet DESSUS ................1 19F CONNECTEUR DE MOULURE......4 élément, faire référence...
- Page 25 Pour commencer l'assemblage, enfoncer une FIXATION TWIST-LOCK® ÉTAPE 7 SAUDER (7F) dans les gros trous des EXTRÉMITÉS (A et B). Répéter cette étape pour la TABLETTE (E) et les MOULURES VERTICALES (R et S). Fixer douze CONSOLES EN MÉTAL (4G) à l'ENTRETOISE (G), à la PLINTHE ARRIÈRE (K) et aux PLINTHES LATÉRALES (L).
- Page 26 Fixer un BOUTON (33K) à la PORTE (H). Utiliser une VIS À MÉTAUX 25 mm DORÉE (50S). Enfoncer un ARRÊT DE PORTE (4I) dans la TABLETTE (E) comme indiqué selon la confi guration de votre porte. Page 26 420519 www.sauder.com/services...
- Page 27 SUJETADOR TWIST-LOCK® ......12 et conserver le livret pour future référence. EXTREMO IZQUIERDO ..........1 15F PASADOR DE MADERA .........4 Pour contacter Sauder PANEL SUPERIOR ............1 19F CONECTOR DE MOLDURA ........4 en ce qui concerne cet FONDO .................1 SOPORTE DE METAL ..........12 élément, faire référence...
- Page 28 Para comenzar el ensamblaje, empuje un SUJETADOR TWIST-LOCK® PASO 7 SAUDER (7F) dentro de los agujeros grandes de los EXTREMOS (A y B). Repita este paso para el ESTANTE (E) y las MOLDURAS VERTICALES (R y S). Fije doce SOPORTES DE METAL (4G) a la RIOSTRA (G), al FALDÓN POSTERIOR (K) y a los FALDONES LATERALES (L).
- Page 29 Fije un POMO (33K) a la PUERTA (H). Utilice un TORNILLO DORADO PARA METAL de 25 mm (50S). Empuje un TOPE DE PUERTA (4I) en el ESTANTE (E) como se muestra de acuerdo con la confi guración de su puerta. www.sauder.com/services 420519 Page 29...
- Page 30 Además, el peso y la ubicación del tubo de imagen tienden a causar la inestabilidad de televisores y son propensos a inclinarse hacia adelante. Page 30 420519 www.sauder.com/services...
- Page 31 à compter de la date d'achat la première fois et qui sont signalés à Sauder dans les limites de couverture de la contre tout défaut de matériaux ou de fabrication des composantes de mobilier Sauder.
- Page 32 Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the Set a world record for speed? purchase and assembly process was a positive experience Feeling good about yourself? and you feel good about the furniture you just built. If you Nice.