Related Manuals for SemaConnect 7 Series
Summary of Contents for SemaConnect 7 Series
- Page 1 Series 7 / 7 Plus EV Charging Station 1 — Last update: 05/19/2021 Installation Manuals Copyright ©2021 SemaConnect, Inc. All rights reserved.
-
Page 2: Table Of Contents
Table of Contents 1. Series 7/7 Plus EV Charging Station ..................... 1 1.1. Safety and Compliance ........................2 1.2. Series 7 Electrical Requirements / Wiring Diagram................4 1.3. Series 7 Plus Electrical Requirements / Wiring Diagram ..............6 1.4. Pedestal Mount ..........................9 1.4.1. -
Page 3: Series 7/7 Plus Ev Charging Station
Installation Manuals Series 7 / 7 Plus EV Charging Station - 1 1. Series 7/7 Plus EV Charging Station Copyright ©2021 SemaConnect, Inc. All rights reserved. Page 1 of 26... -
Page 4: Safety And Compliance
This document describes the most common installation and mounting methods. Contact SemaConnect Inc. where it is not possible to perform an installation using the procedures provided in this document. SemaConnect Inc. is not responsible for damages that may occur or result from installations that are not described in this document. - Page 5 DISTRIBUTORS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. The Series 7 and Series 7 Plus is a trademark of SemaConnect, Inc. All other products or services mentioned are the trademarks, service marks, registered trademarks, or registered service marks of their respective owners.
-
Page 6: Series 7 Electrical Requirements / Wiring Diagram
Connect the station to the side where ground is bonded (in figure 2.C, Line A and Line C). This allows voltages to remain constant regardless of other loads that may be using the lines. Please do not connect to other type of power sources shown below. Copyright ©2021 SemaConnect, Inc. All rights reserved. Page 4 of 26... - Page 7 Series 7 / 7 Plus EV Charging Station - 1 Wiring To System – Separate Power The figure below describes the wiring for installation of Series 7 Charging Station on a separate power circuit. Copyright ©2021 SemaConnect, Inc. All rights reserved. Page 5 of 26...
-
Page 8: Series 7 Plus Electrical Requirements / Wiring Diagram
Line C). This allows voltages to remain constant regardless of other loads that may be using the lines. Please do not connect to other type of power sources shown below. Copyright ©2021 SemaConnect, Inc. All rights reserved. Page 6 of 26... - Page 9 • All data communication is wireless, so there is no data cabling to install, but cellular communication is required. The figure below describes the wiring for installation of Series 7 Plus Charging Station on a separate power circuit. Copyright ©2021 SemaConnect, Inc. All rights reserved. Page 7 of 26...
- Page 10 Installation Manuals Series 7 / 7 Plus EV Charging Station - 1 Copyright ©2021 SemaConnect, Inc. All rights reserved. Page 8 of 26...
-
Page 11: Pedestal Mount
Installation Manuals Series 7 / 7 Plus EV Charging Station - 1 1.4. Pedestal Mount Parts List Anchor Plate Installation Pedestal Installation Station Head Installation Copyright ©2021 SemaConnect, Inc. All rights reserved. Page 9 of 26... -
Page 12: Parts List
1.4.1. Parts List Pedestal Installation Series 7/Series 7 Plus Charging Station Head Unit Pedestal Unit Left and Right Cable Holster Cable Rack Charging Station Anchor Plate Anchor J Bolts (4) Copyright ©2021 SemaConnect, Inc. All rights reserved. Page 10 of 26... - Page 13 Series 7 / 7 Plus EV Charging Station - 1 Pedestal Sacrificial Bolt CMS Sacrificial Bolt Head Unit Mounting Screws (4) Pedestal Mounting Screws (4) Holster Mounting Screws (4) Copyright ©2021 SemaConnect, Inc. All rights reserved. Page 11 of 26...
-
Page 14: Anchor Plate Installation
• Ensure that at least 40” of wire extends out of the conduit. • Insert the anchor plate into the concrete immediately after pouring the concrete. • It is recommended to vibrate the concrete to eliminate any air bubbles. Copyright ©2021 SemaConnect, Inc. All rights reserved. Page 12 of 26... - Page 15 • Anchor plate surface should be in level with the ground. Note: Continuously check for the anchor plate until concrete sets to make sure that anchor plate does not sink into the concrete Copyright ©2021 SemaConnect, Inc. All rights reserved. Page 13 of 26...
-
Page 16: Pedestal Installation
• Ensure that the electric wires can be easily accessed through the access panel provided in the Pedestal’s top section. • Please ensure that access panel is to your right, when seen from the front end. Anchor Bolts and Leveling Screws Copyright ©2021 SemaConnect, Inc. All rights reserved. Page 14 of 26... - Page 17 Loosen the cable rack mount screws. Now attach the Cable Rack to the Pedestal and tighten the screws. Check that the Cable Rack is secure and is firmly attached to the Pedestal. Copyright ©2021 SemaConnect, Inc. All rights reserved. Page 15 of 26...
-
Page 18: Charging Station Head Installation
• Carefully pull these wires a few inches outside of the access panel, to reveal 5 wires coming from the Charging station Head Unit, Figure 13 (for Level-2 charging stations the color codes are Red, Black, Copyright ©2021 SemaConnect, Inc. All rights reserved. Page 16 of 26... - Page 19 CAUTION: Refer to the wire color codes and strictly adhere to this convention while connecting the charging station and electrical supply wires. Incorrect wiring can lead to an electrical hazard. Copyright ©2021 SemaConnect, Inc. All rights reserved. Page 17 of 26...
- Page 20 Call (800) 663-5633 to complete installation. Please have the station serial number ready with you. If you do not have it, you can find it on left hand side of the station. Copyright ©2021 SemaConnect, Inc. All rights reserved. Page 18 of 26...
-
Page 21: Wall Mount
Installation Manuals Series 7 / 7 Plus EV Charging Station - 1 1.5. Wall Mount Parts List Wall Mount Installation Charging Station Head Installation Copyright ©2021 SemaConnect, Inc. All rights reserved. Page 19 of 26... -
Page 22: Parts List
Wall Mount Installation Series 7/Series 7 Plus Charging Station Head Unit Charging Station Wall Mount Unit Left and Right Holster Cable Rack Head Unit Mounting Screws (4) Holster Mounting Screws (4) Copyright ©2021 SemaConnect, Inc. All rights reserved. Page 20 of 26... - Page 23 Installation Manuals Series 7 / 7 Plus EV Charging Station - 1 Copyright ©2021 SemaConnect, Inc. All rights reserved. Page 21 of 26...
-
Page 24: Wall Mount Installation
Now, run conduit up to wire wall hole location previously marked on the wall. Run the wires through this conduit up to wire wall hole location with at least 18” (+wall thickness) free wire. See illustration for clarity. Copyright ©2021 SemaConnect, Inc. All rights reserved. Page 22 of 26... - Page 25 • Now attach the Cable Rack to the wall-mount and tighten the screws (Figure 19). • Check that the Cable Rack is secure and is firmly attached to the wall-mount. Copyright ©2021 SemaConnect, Inc. All rights reserved. Page 23 of 26...
-
Page 26: Charging Station Head Installation
• Also make sure that the striped wires are connected to the left side of the power source. • Once connected, slowly insert the wires into the device and replace the access panel cover using the screws previously removed. Copyright ©2021 SemaConnect, Inc. All rights reserved. Page 24 of 26... - Page 27 CAUTION: Refer to the wire color codes and strictly adhere to this convention while connecting the charging station and electrical supply wires. Incorrect wiring can lead to an electrical hazard. Copyright ©2021 SemaConnect, Inc. All rights reserved. Page 25 of 26...
- Page 28 Call (800) 663-5633 to complete installation. Please have the station serial number ready with you. If you do not have it, you can find it on left hand side of the station. Copyright ©2021 SemaConnect, Inc. All rights reserved. Page 26 of 26...