Advertisement
Quick Links
FOR YOUR SAFETY INSTALL THIS PRODUCT ONLY WHEN THE ENGINE IS COLD. THIS WILL
PREVENT BURNING YOURSELF AND PREVENT THE HOLES IN THE ALUMINUM FROM
STRIPPING OR CROSS THREADING.
M7 Speed engineers and manufactures the highest quality and best fitting Mini Cooper accessories
and performance parts available anywhere on Planet Earth! Please inspect your parts when you
receive them to verify everything is included and no damage has happened during shipment. Read
these instructions completely BEFORE attempting to install this product. If you are not confident you
can do the work described or do not have the tools or skills necessary please contact a local M7
dealer (listed on or website www.m7tuning.com) or a local automotive accessory installation center to
perform this work. We acknowledge not everything is perfect but we work very hard every day to
improve our products and make installations easier. If you have any comments please contact M7
Customer Service directly at 704-663-0094. We encourage and welcome all criticism Good or Bad.
Thank you.
Tools & Supplies Required:
•
T-25 Torx
•
T-27 Torx
•
1/8" hex
•
3/8" combination wrench
•
10mm socket
•
5 mm Hex
Estimated Install Time (Actual time may vary):
30-60 minutes
Parts Checklist
1 AGS-R2 Airbox with cover
1 Pre-Oiled Foam Filter
1 Silicone Elbow
1 AGS-R2 Hardware & Installation Kit #90-1050
08-04-2016
M7 Speed AGS-R2 Ram Air Intake System
56-311701-Fiberglass Housing
56-311801-Carbon Fiber Housing
www.m7speed.com
Page 1 of 6
Mooresville, NC 28117
•
Flathead Screwdriver
•
Phillips Screwdriver
•
Foamy window cleaner or similar
product
•
MAF sensor cleaner (optional)
•
Anti-seize or copper slip
PO Box 3785
888-438-5767
Advertisement
Summary of Contents for M7 SPEED AGS-R2
- Page 1 PREVENT BURNING YOURSELF AND PREVENT THE HOLES IN THE ALUMINUM FROM STRIPPING OR CROSS THREADING. M7 Speed engineers and manufactures the highest quality and best fitting Mini Cooper accessories and performance parts available anywhere on Planet Earth! Please inspect your parts when you receive them to verify everything is included and no damage has happened during shipment.
- Page 2 Once the base is free, rotate it approximately 1/8 to 1/4 turn towards the rear of the car while at the same time pulling it apart from the factory fresh air hose. If the grommets come free from the intake manifold reinstall them now. They are need to mount the AGS-R2 MAF Sensor Clamp...
-
Page 3: Preparation For Installation
PREPARATION FOR INSTALLATION In order to keep the wiring harness safe from chaffing, the MAF sensor has to be slightly rotated before the M7 AGS-R2 is installed. Cut a similar MAF sensor notch in the hose about ¼ of an inch to the left of the original notch. -
Page 4: Installation
PO Box 3785 Mooresville, NC 28117 888-438-5767 2. (Optional) This is a good time to clean your MAF sensor using a specially formulated sensor cleaner you can buy at any local Autoparts store. INSTALLATION 1. Install the modified inlet hose onto the turbo. Do not tighten clamp at this time. 2. - Page 5 Torque to 30 in-lbs (3.4 Nm) 7. Mount the rear bracket onto the AGS-R2 Air Box. Place the rear bracket on the bottom of the air box with the bend and (2) mounting legs at the back. Use (2) #10-32x1/2” lg button head screws and flat washers.
- Page 6 PO Box 3785 Mooresville, NC 28117 888-438-5767 15. Install the supplied air filter. Before installation wipe the inside of the black rubber cuff to thoroughly clean the inside of the filter of any excess oil. Slip the filter cuff over the neck on the inside of the airbox until the grove in the filter and bead on the neck engage.